Valid 300-165 Dumps shared by ExamDiscuss.com for Helping Passing 300-165 Exam! ExamDiscuss.com now offer the newest 300-165 exam dumps, the ExamDiscuss.com 300-165 exam questions have been updated and answers have been corrected get the newest ExamDiscuss.com 300-165 dumps with Test Engine here:
Access 300-165 Dumps Premium Version
(326 Q&As Dumps, 35%OFF Special Discount Code: freecram)
<< Prev Question Next Question >>
Question 16/53
Which two issues explain why a packet is not being routed as desired in a policy-based routing configuration? (Choose two.)
Correct Answer: D,E
- Question List (53q)
- Question 1: Which technology is required in the underlay to facilitate r...
- Question 2: Instructions * This task does not require device configurati...
- Question 3: Which statement accurately describes the implementation of F...
- Question 4: Which option must be configured when you implement a vPC?...
- 1 commentQuestion 5: Instructions * This task does not require device configurati...
- Question 6: Which two Nexus family linecards allow the configuration of ...
- Question 7: What are two requirements for configuring SAN device aliases...
- Question 8: Which two statements are true when performing a SPAN capture...
- Question 9: A Cisco Nexus 2000 Series Fabric Extender is connected to tw...
- Question 10: Which command should you run to enforce SNMP message encrypt...
- Question 11: What can be identified by running the switch# show install a...
- Question 12: When you configure LISP, which two components must be config...
- Question 13: Which two options can be used for link aggregation when you ...
- Question 14: Which two items are services that are provided by Cisco Fabr...
- 1 commentQuestion 15: Which statement accurately describes MP-BGP EVPN?...
- 1 commentQuestion 16: Which two issues explain why a packet is not being routed as...
- Question 17: Which protocol is used to exchange MAC address reachability ...
- 1 commentQuestion 18: Which two options should you consider when you configure a S...
- Question 19: Which option must be enabled to implement manual MACsec?...
- Question 20: ipv6 access-list MY_ACL permit tcp 2001:cc1e:aaaa::/64 2001:...
- Question 21: Which Cisco MDS feature needs to be enabled for Cisco TrustS...
- 1 commentQuestion 22: Which command configures the aging for VLAN 100 to 500 minut...
- Question 23: After enabling strong, reversible 128-bit Advanced Encryptio...
- 1 commentQuestion 24: You plan to configure authentication for OSPF. In which mode...
- Question 25: You experience an issue on a Cisco Nexus 7700 Series switch....
- Question 26: In policy-based routing, which action is taken for packets t...
- 1 commentQuestion 27: Which two options accurately describe the implementation of ...
- Question 28: What are two ways to configure the switch ID for Cisco Fabri...
- 1 commentQuestion 29: What is the Overlay Transport Virtualization site VLAN used ...
- Question 30: You are configuring QoS on a Cisco Nexus 5000 Series switch....
- Question 31: Instructions * This task does not require device configurati...
- Question 32: You have two Fibre Channel switches that are connected via E...
- Question 33: On a Cisco Nexus 7000 Series router, witch statement about H...
- Question 34: Which two protocols can be used to back up the configuration...
- Question 35: You create a checkpoint on a Cisco Nexus 7700 Series switch....
- Question 36: You have a Cisco Nexus 5000 Series switch. Port security is ...
- Question 37: Which statement about SNMP support on Cisco Nexus switches i...
- Question 38: What is an Overlay Transport Virtualization extended VLAN?...
- Question 39: Which statement about electronic programmable logic device i...
- Question 40: Which two features are required to implement a Layer 3 VXLAN...
- Question 41: You have two Cisco Nexus 7700 Series switches named SwitchA ...
- Question 42: Which GLBL load-balancing method ensures that a client is al...
- Question 43: Which implicit rules are applied to all IPv6 ACLs?...
- Question 44: switch# configure terminal switch (config) # interface ether...
- Question 45: N7K-1(config)# feature vpc N7K-1(config)# vpc domain 113 N7K...
- Question 46: Which statement about enhanced zoning on Cisco Multilayer Di...
- Question 47: Which action limits the maximum number of routes that are al...
- Question 48: You plan to implement the OSPF protocol whithin the data cen...
- Question 49: Which LISP component provides connectivity between LISP and ...
- Question 50: Which security feature is only supported on the Cisco Nexus ...
- Question 51: Which command should you ran to distribute NTP configuration...
- Question 52: You are connecting a Cisco Nexus 2300 Series FEX to a Cisco ...
- Question 53: Instructions * This task does not require device configurati...
Recent Comments (The most recent comments are at the top.)
In policy-based routing config the next hop is the first in line to be processed. So for example if the next hop is 192.168.1.1 with metric 32, and the default next hop is 172.16.1.1 with metric 24. Normally based on the routing table the lower metric is more preferred. In case of policy-based routing it still goes to next hop 192.168.1.1 as this is first in line to be processed. And will take an extra hop which is in this case undesired. So for me it would be A and D.
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_pi/configuration/15-mt/iri-15-mt-book/iri-pbr-default-nexthop-route.pdf