Valid 300-165 Dumps shared by ExamDiscuss.com for Helping Passing 300-165 Exam! ExamDiscuss.com now offer the newest 300-165 exam dumps, the ExamDiscuss.com 300-165 exam questions have been updated and answers have been corrected get the newest ExamDiscuss.com 300-165 dumps with Test Engine here:
Access 300-165 Dumps Premium Version
(326 Q&As Dumps, 35%OFF Special Discount Code: freecram)
Online Access Free 300-165 Exam Questions
| Exam Code: | 300-165 |
| Exam Name: | Implementing Cisco Data Center Infrastructure |
| Certification Provider: | Cisco |
| Free Question Number: | 53 |
| Version: | v2018-06-05 |
| Rating: | |
| # of views: | 980 |
| # of Questions views: | 19426 |
| Go To 300-165 Questions | |
Recent Comments (The most recent comments are at the top.)
No.# Should be A. OTV "Site vlan" is used to detect OTV edge devices within the site.
https://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Data_Center/DCI/whitepaper/DCI3_OTV_Intro/DCI_1.html
No.# Question asking for two answers and it gives three... this should be B. and D.
Fiber Channel domain IDs are used within a VSAN. They are the same for every switch within this VSAN.
Domain IDs need to be unique across the fabric (outside the vSAN).
No.# The only correct answer should be B. global configuration.
How do you even configure without entering global config mode?
https://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/4_1/nx-os/security/configuration/guide/sec_nx-os-cfg/sec_keychain.html
No.# aging-time is in seconds so 3000 would be 50 minutes. to be fair, either the question is wrong or the answer is.
If the question is corrected to 50 minutes or the answer is 30000 seconds, then i would go for C.
https://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/nx-os/layer2/configuration/guide/b_Cisco_Nexus_7000_Series_NX-OS_Layer_2_Switching_Configuration_Guide/b_Cisco_Nexus_7000_Series_NX-OS_Layer_2_Switching_Configuration_Guide_chapter_011.html#task_1126206
No.# This should be B and D. Its not necessary to manually activate a SAN zone set manually on all fabric nodes. They actually give you the option to manually do this, but not a requirement. And when you activate a zone set it automatically enables it on all fabric nodes.
No.# This should actually be C. MP-BGP EVPN acts as an control plane for VXLAN to overcome the flood-and-learn limitations.
https://www.cisco.com/c/en/us/products/collateral/switches/nexus-7000-series-switches/white-paper-c11-735015.pdf
No.# This depends on the outcome of the show command config.
You can check this with show license usage and show fcoe. Depending on the outcome of the output you can see if the FCoE license is installed and enabled. Even though FCoE feature is licensed part of the ENTERPRISE_PKG, This license still needs to be installed.
https://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/nx-os/licensing/guide/b_Cisco_NX-OS_Licensing_Guide/licensing_cisco_nx_os_software_features.html
https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/fcoe/b_Cisco_Nexus_5000_Series_NX-OS_Fibre_Channel_over_Ethernet_Configuration_Guide_/Cisco_Nexus_5000_Series_NX-OS_Fibre_Channel_over_Ethernet_Configuration_Guide__chapter3.html
No.# In policy-based routing config the next hop is the first in line to be processed. So for example if the next hop is 192.168.1.1 with metric 32, and the default next hop is 172.16.1.1 with metric 24. Normally based on the routing table the lower metric is more preferred. In case of policy-based routing it still goes to next hop 192.168.1.1 as this is first in line to be processed. And will take an extra hop which is in this case undesired. So for me it would be A and D.
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_pi/configuration/15-mt/iri-15-mt-book/iri-pbr-default-nexthop-route.pdf