Valid DNDNS-200 Dumps shared by ExamDiscuss.com for Helping Passing DNDNS-200 Exam! ExamDiscuss.com now offer the newest DNDNS-200 exam dumps, the ExamDiscuss.com DNDNS-200 exam questions have been updated and answers have been corrected get the newest ExamDiscuss.com DNDNS-200 dumps with Test Engine here:
Access DNDNS-200 Dumps Premium Version
(92 Q&As Dumps, 35%OFF Special Discount Code: freecram)
<< Prev Question Next Question >>
Question 24/60
Refer to the exhibit.
On switch S4820-1, commands are entered. The associated output is as shown.
What correctly defines the state of the Root Bridge for VLAN 2 and VLAN 3?
Correct Answer: C
- Question List (60q)
- Question 1: (Exhibit) Refer to the exhibit. Two S-Series switches have b...
- Question 2: Which component is required to deploy the N2000/N3000 Series...
- 1 commentQuestion 3: A network engineer is assigning any available switchport to ...
- Question 4: (Exhibit) Refer to the exhibit. A network engineer is called...
- Question 5: (Exhibit) Refer to the exhibit of the N-series switches. The...
- Question 6: The network engineer powers on a new S-Series switch. None o...
- Question 7: (Exhibit) Refer to the exhibit. Switch A needs to be able to...
- Question 8: (Exhibit) Refer to the exhibit. The trunk links are being ov...
- Question 9: An N-Series stack has been implemented. The network engineer...
- Question 10: (Exhibit) Refer to the exhibits. A networking engineer is un...
- Question 11: (Exhibit) Refer to the exhibit. Given the output from an N-S...
- Question 12: A network engineer is doing software updates on a C9010 chas...
- Question 13: Which two commands are required to configure OSPFv2 on N-Ser...
- Question 14: A network engineer has configured LACP on two connected S-Se...
- Question 15: A network engineer is configuring several trunk ports for VL...
- Question 16: A network engineer is verifying the configuration of a LAG c...
- Question 17: A network engineer needs to remove switch 2 from a stack of ...
- Question 18: A network engineer removes a new Dell Networking N-Series sw...
- Question 19: (Exhibit) Refer to the exhibits. A network engineer has work...
- Question 20: (Exhibit) Refer to the exhibit. The deployment engineer need...
- Question 21: Which three properties are required for two OSPF router inte...
- Question 22: In an OSPF network, a network engineer uses a loopback inter...
- Question 23: (Exhibit) Refer to the exhibits. An organization has a netwo...
- 1 commentQuestion 24: (Exhibit) Refer to the exhibit. On switch S4820-1, commands ...
- Question 25: (Exhibit) Refer to the exhibit. A customer has a C-Series ch...
- Question 26: (Exhibit) Refer to the exhibit. A customer plans to deploy a...
- Question 27: (Exhibit) Refer to the exhibits. A customer upgrades its C-S...
- Question 28: A networking engineer needs to configure several VLANs for S...
- Question 29: By default, how often are Bridge Protocol Data Units (BPDUs)...
- Question 30: A network engineer needs to install five Dell N-Series switc...
- Question 31: A network engineer needs to apply Layer 2 port security on a...
- Question 32: A network engineer needs to create an IEEE 802.3ad Port-Chan...
- Question 33: A network deployment engineer needs to deploy four Dell Netw...
- Question 34: When facing the front of a C-Series switch, in which directi...
- Question 35: A new switch is already configured with an IP address and is...
- Question 36: A network engineer configures a new S-Series switch. When th...
- Question 37: On an S-Series switch, what two events occur when a static n...
- Question 38: Which three cabling items should be considered when stacking...
- Question 39: (Exhibit) Refer to the exhibit. A network engineer is instal...
- Question 40: (Exhibit) Refer to the exhibit. Considering the network topo...
- Question 41: What are three characteristics of port-based VLANs on S-Seri...
- Question 42: A network engineer needs to make sure that the first 16 swit...
- Question 43: In an OSPF network, what happens if the OSPF Priority level ...
- Question 44: A customer has two locations that are six miles apart and co...
- Question 45: Refer to the output. (Exhibit) According to the partial conf...
- Question 46: The network engineer has two Dell Networking switches: an N-...
- Question 47: (Exhibit) Refer to the exhibit. A customer has a SAN deploym...
- Question 48: A network engineer has connected a Port Extender to a C-Seri...
- Question 49: The status LED is blinking RED for an N-Series switch. Which...
- Question 50: A customer needs to convert S-Series stacked switches to a V...
- Question 51: A network engineer is implementing MLAG using two N-Series s...
- Question 52: (Exhibit) Refer to the Exhibit. A network engineer receives ...
- Question 53: (Exhibit) Refer to the exhibit. On switch S4820-2, commands ...
- Question 54: Two Dell S-Series Switches are directly connected. (Exhibit)...
- Question 55: Which three components can be used to deploy 10GbE N-Series ...
- Question 56: A network engineer needs to summarize the IP range of addres...
- Question 57: (Exhibit) Refer to the exhibit. Two S-Series switches are co...
- Question 58: On an N-Series switch, which three outputs display when a ne...
- Question 59: (Exhibit) Refer to the exhibits of the S-Series switch. A ne...
- Question 60: Which two management protocols are most secure? (Choose two....
Recent Comments (The most recent comments are at the top.)
I think this answer is wrong because the commando was executed on switch S4820-1 and change the root bridge priority to 4096. This value is minor then 32768 that was in S4820-2