Valid DNDNS-200 Dumps shared by ExamDiscuss.com for Helping Passing DNDNS-200 Exam! ExamDiscuss.com now offer the newest DNDNS-200 exam dumps, the ExamDiscuss.com DNDNS-200 exam questions have been updated and answers have been corrected get the newest ExamDiscuss.com DNDNS-200 dumps with Test Engine here:
Access DNDNS-200 Dumps Premium Version
(92 Q&As Dumps, 35%OFF Special Discount Code: freecram)
<< Prev Question Next Question >>
Question 4/60
Refer to the exhibit.
A network engineer is called onsite to troubleshoot replication failure and traffic loss. Whenever replication occurs between SAN A and SAN B, users report traffic loss between sites, and replication ultimately fails due to traffic loss.
Based on the topology shown, what is the most likely cause of the traffic loss?
Correct Answer: C
Explanation/Reference:
Explanation:
In Quality of Service, DSCP value 46 is high-priority traffic.
Explanation:
In Quality of Service, DSCP value 46 is high-priority traffic.
- Question List (60q)
- Question 1: (Exhibit) Refer to the exhibit. Two S-Series switches have b...
- Question 2: Which component is required to deploy the N2000/N3000 Series...
- 1 commentQuestion 3: A network engineer is assigning any available switchport to ...
- Question 4: (Exhibit) Refer to the exhibit. A network engineer is called...
- Question 5: (Exhibit) Refer to the exhibit of the N-series switches. The...
- Question 6: The network engineer powers on a new S-Series switch. None o...
- Question 7: (Exhibit) Refer to the exhibit. Switch A needs to be able to...
- Question 8: (Exhibit) Refer to the exhibit. The trunk links are being ov...
- Question 9: An N-Series stack has been implemented. The network engineer...
- Question 10: (Exhibit) Refer to the exhibits. A networking engineer is un...
- Question 11: (Exhibit) Refer to the exhibit. Given the output from an N-S...
- Question 12: A network engineer is doing software updates on a C9010 chas...
- Question 13: Which two commands are required to configure OSPFv2 on N-Ser...
- Question 14: A network engineer has configured LACP on two connected S-Se...
- Question 15: A network engineer is configuring several trunk ports for VL...
- Question 16: A network engineer is verifying the configuration of a LAG c...
- Question 17: A network engineer needs to remove switch 2 from a stack of ...
- Question 18: A network engineer removes a new Dell Networking N-Series sw...
- Question 19: (Exhibit) Refer to the exhibits. A network engineer has work...
- Question 20: (Exhibit) Refer to the exhibit. The deployment engineer need...
- Question 21: Which three properties are required for two OSPF router inte...
- Question 22: In an OSPF network, a network engineer uses a loopback inter...
- Question 23: (Exhibit) Refer to the exhibits. An organization has a netwo...
- 1 commentQuestion 24: (Exhibit) Refer to the exhibit. On switch S4820-1, commands ...
- Question 25: (Exhibit) Refer to the exhibit. A customer has a C-Series ch...
- Question 26: (Exhibit) Refer to the exhibit. A customer plans to deploy a...
- Question 27: (Exhibit) Refer to the exhibits. A customer upgrades its C-S...
- Question 28: A networking engineer needs to configure several VLANs for S...
- Question 29: By default, how often are Bridge Protocol Data Units (BPDUs)...
- Question 30: A network engineer needs to install five Dell N-Series switc...
- Question 31: A network engineer needs to apply Layer 2 port security on a...
- Question 32: A network engineer needs to create an IEEE 802.3ad Port-Chan...
- Question 33: A network deployment engineer needs to deploy four Dell Netw...
- Question 34: When facing the front of a C-Series switch, in which directi...
- Question 35: A new switch is already configured with an IP address and is...
- Question 36: A network engineer configures a new S-Series switch. When th...
- Question 37: On an S-Series switch, what two events occur when a static n...
- Question 38: Which three cabling items should be considered when stacking...
- Question 39: (Exhibit) Refer to the exhibit. A network engineer is instal...
- Question 40: (Exhibit) Refer to the exhibit. Considering the network topo...
- Question 41: What are three characteristics of port-based VLANs on S-Seri...
- Question 42: A network engineer needs to make sure that the first 16 swit...
- Question 43: In an OSPF network, what happens if the OSPF Priority level ...
- Question 44: A customer has two locations that are six miles apart and co...
- Question 45: Refer to the output. (Exhibit) According to the partial conf...
- Question 46: The network engineer has two Dell Networking switches: an N-...
- Question 47: (Exhibit) Refer to the exhibit. A customer has a SAN deploym...
- Question 48: A network engineer has connected a Port Extender to a C-Seri...
- Question 49: The status LED is blinking RED for an N-Series switch. Which...
- Question 50: A customer needs to convert S-Series stacked switches to a V...
- Question 51: A network engineer is implementing MLAG using two N-Series s...
- Question 52: (Exhibit) Refer to the Exhibit. A network engineer receives ...
- Question 53: (Exhibit) Refer to the exhibit. On switch S4820-2, commands ...
- Question 54: Two Dell S-Series Switches are directly connected. (Exhibit)...
- Question 55: Which three components can be used to deploy 10GbE N-Series ...
- Question 56: A network engineer needs to summarize the IP range of addres...
- Question 57: (Exhibit) Refer to the exhibit. Two S-Series switches are co...
- Question 58: On an N-Series switch, which three outputs display when a ne...
- Question 59: (Exhibit) Refer to the exhibits of the S-Series switch. A ne...
- Question 60: Which two management protocols are most secure? (Choose two....
