300-101 Exam Dumps | If the total bandwidth is 64 kbps and the RTT is 3 seconds, what is the bandwidth delay product?

<< Prev Question Next Question >>

Question 412/477

If the total bandwidth is 64 kbps and the RTT is 3 seconds, what is the bandwidth delay product?

A. 8,000 bytes

B. 16,000 bytes

C. 24,000 bytes

D. 32,000 bytes

E. 62,000 bytes

Question List (477q): Question 1: Refer to the exhibit. (Exhibit) After configuring the rotes,...; Question 2: Refer to the exhibit. (Exhibit) Network users on the 10.1.2....; Question 3: A network administrator notices that the BGP state and logs ...; Question 4: A network engineer is trying to modify an existing active NA...; Question 5: What is the reasons of command: router(config)# snmp-server ...; Question 6: A network engineer is notified that several employees are ex...; Question 7: The network engineer types the follow commands in a router: ...; Question 8: Which two methods of deployment can you use when implementin...; Question 9: Which two technologies can encapsulate an IPv6 payload in an...; Question 10: Which condition must be met before two EVN devices can conne...; Question 11: Which two OSPF router types can perform summarization in an ...; Question 12: Which type of address does OSPFv3 use to form neighbor adjac...; Question 13: Which command will display all the EIGRP feasible successor ...; Question 14: Which feature can mitigate fragmentation issues within netwo...; Question 15: Which two protocols are required for DMVPN? (Choose two.)...; Question 16: A network engineer is disabling split horizon on a point-to-...; Question 17: How should a router that is being used in a Frame Relay netw...; Question 18: Which two options can you use to configure an EIGRP stub rou...; Question 19: In SNMP v3, which security level provides encryption of the ...; Question 20: Refer to the exhibit. (Exhibit) Which statement about this n...; Question 21: How is authentication handled with OSPFv3? Select the best r...; Question 22: A network engineer wants to implement an SNMP notification p...; Question 23: Refer to the exhibit. You want router r1 to perform unequal-...; Question 24: Which two statements about EVN are true? (Choose two.)...; Question 25: Which Cisco IOS VPN technology leverages Ipsec, mGRE, dynami...; Question 26: Instructions: - Enter IOS commands on the device to verify n...; Question 27: A corporate policy requires PPPoE to be enabled and to maint...; Question 28: What is the NHRP role in DMVPN? (Choose two.)...; Question 29: Refer to the exhibit. (Exhibit) The excerpt was taken from t...; Question 30: The Cisco SA 500 Series Security Appliances are built specif...; Question 31: Which method allows IPv4 and IPv6 to work together without r...; Question 32: OSPF chooses routes in which order, regardless of route's ad...; Question 33: Which statement about the NPTv6 protocol is true?...; Question 34: When a new PC is connected to the network, which step must i...; Question 35: Which of the following is a GRE Tunnel characteristic?...; Question 36: The Neighbor Discovery Protocol in IPv6 replaces which proto...; Question 37: A network access server using TACACS+ for AAA operations rec...; Question 38: Which two features are provided by EIGRP for IPv6? (Choose t...; Question 39: Prior to enabling PPPoE in a virtual private dialup network ...; Question 40: Which criterion does BGP evaluate first when determining the...; Question 41: After testing various dynamic IPv6 address assignment method...; Question 42: An engineer is asked to monitor the availability of the next...; Question 43: Which two tasks must you perform when you install SSH on a C...; Question 44: Which LAN feature enables a default gateway to inform its en...; Question 45: Scenario You have been asked to evaluate an OSPF network set...; Question 46: Which two packet types can an EIGRP router send when a route...; Question 47: Refer to the exhibit. EIGRP is configured on all routers in ...; Question 48: By default, which statement is correct regarding the redistr...; Question 49: What is the effect of the following two commands? (Choose tw...; Question 50: A router with an interface that is configured with ipv6 addr...; Question 51: (Exhibit) Refer to the exhibit. A network engineer has confi...; Question 52: A company's corporate policy has been updated to require tha...; Question 53: A router is configured for redistribution to advertise EIGRP...; Question 54: Which three statements are true when configuring redistribut...; Question 55: In a point-to-multipoint Frame Relay topology, which two met...; Question 56: Refer to the exhibit. (Exhibit) Which statement is correct r...; Question 57: Which condition prevents the establishment of a DMVPN tunnel...; Question 58: Refer to the exhibit. (Exhibit) Which statement about the co...; Question 59: Refer to the exhibit. The network setup is running the RIP r...; Question 60: (Exhibit) Refer to the exhibit. All interfaces on each route...; Question 61: Which two commands must you configure in the calling router ...; Question 62: Which of the following are characteristics of TACACS+? (Choo...; Question 63: Which two LSA types were introduced to support OSPF for IPv6...; Question 64: Which Cisco VPN technology uses AAA to implement group polic...; Question 65: Refer to the exhibit. Which three NTP features can be deduce...; Question 66: Refer to exhibit. What is indicated by the show ip cef comma...; Question 67: (Exhibit) Refer to the exhibit. A network engineer is troubl...; Question 68: Which two tasks does a DHCP relay agent perform? (Choose two...; Question 69: What are the four main steps in configuring a GRE tunnel ove...; Question 70: Which option is one way to mitigate symmetric routing on an ...; Question 71: Which keyword of the aaa authentication ppp command applies ...; Question 72: Which protocol does VRF-Lite support?...; Question 73: What is the default OSPF hello interval on a Frame Relay poi...; Question 74: When a tunnel interface is configured in the default mode, w...; Question 75: A customer asks its service provider for VPN support IPv4 an...; Question 76: Which two features does RADIUS combine? (Choose two.)...; Question 77: An IPv6 overlay tunnel is required to communicate with isola...; Question 78: Which protocol can you use to remotely install an IOS on a C...; Question 79: Refer to the exhibit. configure terminal ip flow-export dest...; Question 80: Which three items can you track when you use two time stamps...; Question 81: Which two debug commands can you use to view issues with CHA...; Question 82: Which two statements about route targets that are configured...; Question 83: Refer to the exhibit. (Exhibit) A network administrator chec...; Question 84: Which two authentication protocols does PPP support? (Choose...; Question 85: The company network is in the process of migrating the IP ad...; Question 86: Refer to the exhibit. (Exhibit) Which statement about redist...; Question 87: Refer to the exhibit. Based upon the configuration, you need...; Question 88: A network engineer has configured a tracking object to monit...; Question 89: Which address is used by the Unicast Reverse Path Forwarding...; Question 90: Which IPV6 address type does RIPng use for next-hop addresse...; Question 91: Which algorithm is used by EIGRP to determine the best path ...; Question 92: Which outbound access list, applied to the WAN interface of ...; Question 93: Which NAT Command do you enter to disable dynamic ARP learni...; Question 94: Which option is a prerequisite for stateful NAT64?...; Question 95: Which two statements indicate a valid association mode for N...; Question 96: What command would you use to set EIGRP routes to be priorit...; Question 97: Which command must be globally enabled on a Cisco router to ...; Question 98: Which protocols support DMVPN?; Question 99: Which three functionalities are specific to stateful NAT64? ...; Question 100: Which problem can be caused by latency on a UDP stream?...; Question 101: What is VRF-Lite?; Question 102: Which two among the following are used to indicate external ...; Question 103: Which two statements about NTP stratum are true? (Choose two...; Question 104: Refer to the exhibit. (Exhibit) A network engineer receives ...; Question 105: What is true about EIGRP's redistributed static routes and s...; Question 106: A network engineer initiates the ip sla responder tcp-connec...; Question 107: Which CLI command can you enter to permit or deny IPv6 traff...; Question 108: Which NetFlow component is applied to an interface and colle...; Question 109: Which two statements are benefits of BGP peer groups? (Choos...; Question 110: A user is having issues accessing file shares on a network. ...; Question 111: Scenario You have been asked to evaluate an OSPF network set...; Question 112: When a packet is denied by an IPv6 traffic filter, which add...; Question 113: (Exhibit) A senior network engineer tries to propagate a sum...; Question 114: Which two EIGRP metrics have nonzero K values by default? (C...; Question 115: A network engineer wants to ensure an optimal end-to-end del...; Question 116: What are two important differences between OSPFv2 and OSPFv3...; Question 117: Which SNMP model and level can provide DES encryption?...; Question 118: Which two causes of latency are true? (Choose two.)...; Question 119: How does an EVN provide end-to-end virtualization and separa...; Question 120: Which option describes why the EIGRP neighbors of this route...; Question 121: Which two statements about NetFlow version 9 are true? (Choo...; Question 122: What is the default authentication in RIPv2 when authenticat...; Question 123: Using new backup router in spite of faulty one in ospf domai...; Question 124: A network engineer notices that transmission rates of sender...; Question 125: Refer to the exhibit. Which statement about the configuratio...; Question 126: Which IPv6 address type is seen as the next-hop address in t...; Question 127: A network engineer is configuring a routed interface to forw...; Question 128: What two situations could require the use of multiple routin...; Question 129: Which IP SLA deployment cycle reduces the deployment time fo...; Question 130: Which two statements about AAA implementation in a Cisco rou...; Question 131: Which LSA type on OSPFv3 is used for link-local updates?...; Question 132: A Network engineer wants to configure logging to compile and...; Question 133: What would you configure on SNMPv3 to allow authentication a...; Question 134: Which three functionalities are specific to stateful NAT64? ...; Question 135: Which three characteristics are shared by subinterfaces and ...; Question 136: Refer to the exhibit. The command is executed while configur...; Question 137: A network engineer wants to verify the status of a recently ...; Question 138: Refer to the exhibit. (Exhibit) A network engineer is modify...; Question 139: Which two statements about PAP and CHAP authentication are t...; Question 140: Which statement about dual stack is true?...; Question 141: Which Cisco VPN technology can use multipoint tunnel, result...; Question 142: Which feature can filter information at the interface level?...; Question 143: A network administrator is attempting to configure IP SLA to...; Question 144: OSPF routers that communicate with other network routers lik...; Question 145: Observe the exhibit. (Exhibit) If the command variance 3 wer...; Question 146: Which of the following are features of Netflow version 9?...; Question 147: You need the IP address of the devices with which the router...; Question 148: Refer to the exhibit. Which statement about the command outp...; Question 149: Which alerts will be seen on the console when running the co...; Question 150: Device R1 has 1 Gigabit and 10 Gigabit Ethernet interfaces. ...; Question 151: Which protocol is used in a DMVPN network to map physical IP...; Question 152: Which action can you take to mitigate unicast flooding in a ...; Question 153: Which two options are requirements for EIGRP authentication?...; Question 154: Scenario You have been asked to evaluate an OSPF network set...; Question 155: (Exhibit) The configuration of R1 to R6 are posted below for...; Question 156: Which IP SLA operation can be used to measure round-trip del...; Question 157: Which two statements about NTP operation are true? (Choose t...; Question 158: Refer to the following: Logging Console 7 Which option is on...; Question 159: Which two statement about GRE tunnel interface are true? (Ch...; Question 160: Which routing protocol does DMVPN support? (Choose three.)...; Question 161: (Exhibit) Which of the following is true?...; Question 162: Which technology does Easy Virtual Network use?...; Question 163: Various employees in the same department report to the netwo...; Question 164: Which two protocols are used to deploy a single Hub-DMVPN su...; Question 165: Which type of IPv6 address is an identifier for a single int...; Question 166: Which routing protocol routers traffic through the best path...; Question 167: Refer to the exhibit. (Exhibit) If this configuration is app...; Question 168: Refer to the exhibit. When summarizing these routes, which r...; Question 169: When an IPv6 enabled host boots, it sends a router solicitat...; Question 170: What is a valid ipv6 multicast address?...; Question 171: If you run the command auto-cost reference-bandwidth 10000 o...; Question 172: Which two statements about configuring Frame Relay point-to-...; Question 173: (Exhibit) Refer to the exhibit. Which statement describes th...; Question 174: Choose the best IP SLA deployment cycle that reduce deployme...; Question 175: Which two configurations can a PPPoE client support? (Choose...; Question 176: Which two statements about 6to4 tunneling are accurate? (Cho...; Question 177: A network administrator is troubleshooting a redistribution ...; Question 178: (Exhibit) Refer to the exhibit. Based on Cisco best practice...; Question 179: Which statement is true about the command ipv6 ospf 1 area 0...; Question 180: An engineer executes the ip flow ingress command in interfac...; Question 181: What are two limitations when in use of NPTv6 for IPV6 vs IP...; Question 182: What does the command show ip vrf purple TOPOLOGY shows?...; Question 183: Which statement describes the difference between a manually ...; Question 184: What is the function of the snmp-server manager command?...; Question 185: How to set up IP SLA to monitor Bandwidth between the certai...; Question 186: Using the rules for IPv6 addressing, how can the address 203...; Question 187: Refer to the exhibit. Which command would verify if PBR reac...; Question 188: Your network consists of a large hub-and-spoke Frame Relay n...; Question 189: Which command do you enter to display log messages with a ti...; Question 190: Which command should be added to RTB under router bgp 100 to...; Question 191: Which IPv6 address correctly compresses the IPv6 unicast add...; Question 192: Which two routers can do OSPF route summarization? (Choose t...; Question 193: A network administrator recently redistributed RIP routes in...; Question 194: Refer to the exhibit. Which option prevents routing updates ...; Question 195: A network administrator is troubleshooting a DMVPN setup bet...; Question 196: Refer to the exhibit. What two statements are true? (Choose ...; Question 197: When the tunnel interface is configured in default mode, whi...; Question 198: Refer to the exhibit. In the network diagram, Area 1 is defi...; Question 199: Refer to the exhibit. Will redistributed RIP routes from OSP...; Question 200: Which three configuration parameters can a DHCPV6 pool conta...; Question 201: Frame Relay LMI autosense. Which statements are true? (Choos...; Question 202: Which two BGP neighbor states are valid? (Choose two.)...; Question 203: Which next hop is going to be used for 172.17.1.0/24 ? (Exhi...; Question 204: Which functions are included in the two-message rapid exchan...; Question 205: What are three reasons to control routing updates via route ...; Question 206: What from the following can cause an issue for uRPF?...; Question 207: Consider this scenario. TCP traffic is blocked on port 547 b...; Question 208: A network engineer executes the commands logging host 172.16...; Question 209: What number is a valid representation for the 200F:0000:AB00...; Question 210: Refer to the exhibit. (Exhibit) Based on this FIB table, whi...; Question 211: (Exhibit) Based on the configuration information shown above...; Question 212: If you want to migrate an IS-IS network to another routing p...; Question 213: Which two protocols can be affected by MPP? (Choose two.)...; Question 214: What is a key benefit of using a GRE tunnel to provide conne...; Question 215: Refer to the exhibit. Which effect of this configuration is ...; Question 216: Refer to the exhibit. A new TAC engineer came to you for adv...; Question 217: Which statement about the split-horizon rule for distance ve...; Question 218: What does the show ip route vrf CISCO command display?...; Question 219: What is the default value of TCP maximum segment size?...; Question 220: What command can you enter to configure an enable password t...; Question 221: Which three statements about SNMP are true? (Choose three.)...; Question 222: The following configuration is applied to a router at a bran...; Question 223: Router E is configured with the EIGRP variance 2 command. (E...; Question 224: Refer to the exhibit. (Exhibit) Why is the default route not...; Question 225: Which routing protocol will continue to receive and process ...; Question 226: Which location is traffic from IP SLAs?...; Question 227: For security purposes, an Ipv6 traffic filter was configured...; Question 228: Which PPP authentication method sends authentication informa...; Question 229: A network engineer wants an NTP client to be able to update ...; Question 230: A company is deploying a multicast application that must be ...; Question 231: Which Cisco Express Forwarding table or tables hold forwardi...; Question 232: A network engineer is configuring two dedicated Internet con...; Question 233: Which two options are components of a dual stack? (Choose tw...; Question 234: What does the following access list, which is applied on the...; Question 235: Which statement is true about 6to4 tunneling?...; Question 236: (Exhibit) Refer to the exhibit. A network engineer is workin...; Question 237: A customer requests policy-based routing. Packets arriving f...; Question 238: Which option is one way to mitigate asymmetric routing on an...; Question 239: Refer to Exhibit. (Exhibit) Which two reasons for IP SLA tra...; Question 240: To configure SNMPv3 implementation, a network engineer is us...; Question 241: Refer to the exhibit. (Exhibit) Which command is used to con...; Question 242: Which Technology supports overlapping IP address on a single...; Question 243: A network administrator uses GRE over IPSec to connect two b...; Question 244: Which three protocols are supported with EVN? (Choose three....; Question 245: (Exhibit) Refer to the exhibit. Which networking challenge i...; Question 246: Which traffic does the following configuration allow? Ipv6 a...; Question 247: Router R1, a branch router, connects to the Internet using D...; Question 248: Refer to the exhibit. (Exhibit) R1 and R2 belong to the RIP ...; Question 249: (Exhibit) Which interoperability technique implemented on th...; Question 250: You are configuring a Microsoft client to call a PPP server ...; Question 251: What configurations does PPPoE allow? (Choose two.)...; Question 252: During a recent OSPF election among three routers, RTA was e...; Question 253: What do we prioritize with LLQ?...; Question 254: Which two GRE features can you configure to prevent fragment...; Question 255: When ospf is forming an adjacency, in which state does the a...; Question 256: Which two statements about NHRP in a DMVPN environment are t...; Question 257: Which statement describes what this command accomplishes whe...; Question 258: Which two types of threshold can you configure for tracking ...; Question 259: Windows Server Syslog blocked by ACL and....?...; Question 260: You have a router that has some interfaces configured with 1...; Question 261: You are configuring a static route. Which action must you ta...; Question 262: Which two options for authenticating a user who is attemptin...; Question 263: Which Cisco Express Forwarding components maintains Layer 2 ...; Question 264: Study this exhibit below carefully. (Exhibit) What is the ef...; Question 265: Which feature is supported with the PPPoE client?...; Question 266: Which three problems result from application mixing of UDP a...; Question 267: Which of the following NSAP addresses is a private, locally ...; Question 268: What are the three modes of Unicast Reverse Path Forwarding?...; Question 269: Refer to the exhibit. Router 1 cannot ping router 2 via the ...; Question 270: A company has their headquarters located in a large city wit...; Question 271: A network engineer configures two connected routers to run O...; Question 272: For a GRE tunnel to be up between two routers, which of the ...; Question 273: Refer to the exhibit. Which effect of this configuration is ...; Question 274: Which SNMP security level is available across all versions o...; Question 275: A network engineer needs to verify IP SLA operations on an i...; Question 276: Case study. (Exhibit) Some notices from above configuration:...; Question 277: An EUl-64 bit address is formed by inserting which 16-bit va...; Question 278: A network engineer executes the show ip cache flow command. ...; Question 279: What show command is used here? TCB Local Address Foreign Ad...; Question 280: Which configuration is applied to a device so that it blocks...; Question 281: Which two OSPF area types filter type 4 and type 5 LSAs? (Ch...; Question 282: A network engineer recently deployed Easy Virtual Networking...; Question 283: Refer to the exhibit. Which BGP attribute can be used to inf...; Question 284: The Dev-1 and Dev-3 routers are OSPF neighbors over the Ethe...; Question 285: Congestion in the network. What is the effect on UDP?...; Question 286: A network engineer is troubleshooting connectivity issues wi...; Question 287: Which two statements about VRF-Lite configurations are true?...; Question 288: A network engineer is asked to create an SNMP-enabled proact...; Question 289: Refer to the exhibit. (Exhibit) How would you confirm on R1 ...; Question 290: Which statement about stateless and stateful IPv6 autoconfig...; Question 291: An administrator types in the command router ospf 1 and rece...; Question 292: Which technology uses the many-to-one method of mapping IP a...; Question 293: Which value determines the amount of traffic that a network ...; Question 294: Which statement is true?; Question 295: Which two statements about GRE tunnel interfaces are true? (...; Question 296: Which two effects of asymmetric routing are true? (Choose tw...; Question 297: Which type of traffic does DHCP snooping drop?...; Question 298: Which statement is true about an IPsec/GRE tunnel?...; Question 299: Which two address types are included in NAT? (Choose two.)...; Question 300: Which three methods can a network engineer use to fix a metr...; Question 301: Refer to the exhibit. After configuring GRE between two rout...; Question 302: NPTv6 restrictions? (Choose all that apply.)...; Question 303: What is the viable successor of NAT_PT?...; Question 304: OSPF chooses routes in which order, regardless of route's ad...; Question 305: If you configure one router in your network with the auto-co...; Question 306: In which two ways can split horizon issues be overcome in a ...; Question 307: Which adverse circumstance can the TTL feature prevent?...; Question 308: Which feature is an invalid redistribute command option for ...; Question 309: Which statement about the use of tunneling to migrate to IPv...; Question 310: Which access list used to filter upper layer protocol?...; Question 311: Refer to the exhibit. (Exhibit) Which two statements are tru...; Question 312: Which technology is required on an EVN trunk interface?...; Question 313: Which two statements about EVNs are true? (Choose two.)...; Question 314: A network engineer wants to notify a manager in the event th...; Question 315: An administrator needs to setup an NTP client to provide upd...; Question 316: (Exhibit) How many times was SPF alrogithm executed on R4 fo...; Question 317: Which two statements about AAA with the local database are t...; Question 318: The OSPF database of a router shows LSA types 1, 2, 3, and 7...; Question 319: What is the maximum number of hops on a router that RIPng ad...; Question 320: Which BGP option is required when load sharing over multiple...; Question 321: Refer to the exhibit. Why is the 140.140.0.0 network not use...; Question 322: Refer to the exhibit. (Exhibit) How can you change this conf...; Question 323: Which type of message does a device configured with the eigr...; Question 324: Into which two types of areas would an area border router (A...; Question 325: You want to configure a device to select an OSPF-learned rou...; Question 326: How does an IOS router process a packet that should be switc...; Question 327: Which set of actions does a network engineer perform to set ...; Question 328: What happens when a router receives a route with an administ...; Question 329: RIPng ____________.; Question 330: Which command instruct a PPPoE client to obtain its IP addre...; Question 331: Which SNMP verification command shows the encryption and aut...; Question 332: Redistributing BGP into OSPF what statement is correct? rout...; Question 333: To enable policy-based routing, which function specifies the...; Question 334: (Exhibit) Refer to the exhibit. Which effect of this configu...; Question 335: What is the minimum privilege level to enter all commands in...; Question 336: What is true about peer groups? (Choose two.)...; Question 337: Which value does a point-to-point GRE tunnel use to identity...; Question 338: Which two statements about EVN are true? (Choose two.)...; Question 339: The Neighbor Discovery Protocol in ipv6 is replaced with whi...; Question 340: A router was configured with the eigrp stub command. The rou...; Question 341: Which three causes of unicast flooding are true? (Choose thr...; Question 342: Refer to the exhibit. Based on the output from the show comm...; Question 343: Which type of handshake does CHAP authentication use to esta...; Question 344: Which two statements about OSPF E1 routes are true? (Choose ...; Question 345: Which the Valid range for BGP private ASNs?...; Question 346: Which purpose of the AAA accounting feature is true when you...; Question 347: Which two tasks must you perform to configure a BGP peer gro...; Question 348: Which two commands must you configure on a DMVPN hub to enab...; Question 349: Refer to the exhibit. Which three statements accurately desc...; Question 350: (Exhibit) A network engineer is working on the network topol...; Question 351: Which IP SLA operation requires Cisco endpoints?...; Question 352: Scenario You have been asked to evaluate how EIGRP is functi...; Question 353: IP CEF load-sharing options (Choose three.)...; Question 354: Which authentication methods are EIGRP uses?...; Question 355: What does the following access list, which is applied on the...; Question 356: PPPoE requires certain signals and information to establish,...; Question 357: Which values identifies VPNs in an EVN environment?...; Question 358: What attribute is used to influce traffic form AS200 and AS3...; Question 359: When policy-based routing (PBR) is being configured, which t...; Question 360: Which two commands do you need to implement on a router to s...; Question 361: Which three statements about configuring OSPF in a IPv6 netw...; Question 362: Refer to the exhibit. Which two effects of this configuratio...; Question 363: Which command is needed to get the ip address assigned from ...; Question 364: Which command enables NAT-PT on an IPv6 interface?...; Question 365: Which functionality is required within an IP router that is ...; Question 366: Which mode of uRPF causes a router interface to accept a pac...; Question 367: Which three statements about IPv6 EIGRP are true? (Choose th...; Question 368: Which two statements are true of the OSPF link-state routing...; Question 369: Refer to the exhibit. (Exhibit) Which two statements are cor...; Question 370: Your company uses Voice over IP (VoIP). The system sends UDP...; Question 371: Users were moved from the local DHCP server to the remote co...; Question 372: Which statement about local policy routing is true?...; Question 373: Refer to the exhibit. (Exhibit) For which reason is EIGRP fa...; Question 374: If routers in a single area are configured with the same pri...; Question 375: Which three steps are most helpful in verifying proper route...; Question 376: Which two statements about DMVPN are true? (Choose two.)...; Question 377: When does a Cisco router send an ICMP redirect?...; Question 378: On which two types of interface is Frame Relay switching sup...; Question 379: Technologies used in preparing Service Provider IPv6? (Choos...; Question 380: Which statement best describes the following two OSPF comman...; Question 381: Which two statements about NetFlow templates are true? (Choo...; Question 382: A policy needs to be implemented on Router B so that any tra...; Question 383: Refer to the exhibit. (Exhibit) Which option represents the ...; Question 384: Which task must you perform to enable a point-to-point Frame...; Question 385: Which two types of authentication does EIGRP offer? (Choose ...; Question 386: What is a function of NPTv6?; Question 387: Ipv6 has just been deployed to all of the hosts within a net...; Question 388: Which command do you enter on router R6 so that BGP supports...; Question 389: Refer to the exhibit. (Exhibit) After configuring the rotes,...; Question 390: What are three key concepts that apply when configuring the ...; Question 391: Which STP feature can reduce TCNs on ports that are connecte...; Question 392: Refer to the exhibit. (Exhibit) Which option prevents routin...; Question 393: A route map was configured and it was distributing OSPF exte...; Question 394: What are the default timers for RIPng?...; Question 395: Which option is the minimum privilege level that allows the ...; Question 396: To configure 6to4 on a dual-stack edge router. Which three o...; Question 397: Which command creates a manual summary on an interface when ...; Question 398: What is show on logging console 7?...; Question 399: What is EIGRP Summary Route Administrative Distance?...; Question 400: What type of IPv6 packet will indicate traffic from single h...; Question 401: A network engineer executes the show ip sla statistics comma...; Question 402: Based on the configuration command below, which statement is...; Question 403: Refer to the exhibit. The DHCP client is unable to receive a...; Question 404: Which item does EIGRP IPv6 require before it can start runni...; Question 405: Which two commands do you need to implement on the CALLING r...; Question 406: Which are new LSA types in OSPF for IPv6 (OSPFv3)? (Choose t...; Question 407: What following parameters for the EIGRP authentication need ...; Question 408: Refer to the exhibit. (Exhibit) An engineer is enabling VPN ...; Question 409: What are 2 protocols used for user with authentication on ne...; Question 410: What appears in the other router routing table? #loopback EI...; Question 411: Which location within the network is preferred when using a ...; Question 412: If the total bandwidth is 64 kbps and the RTT is 3 seconds, ...; Question 413: Which three TCP enhancements can be used with TCP selective ...; Question 414: Refer to the exhibit. (Exhibit) After configuring the routes...; Question 415: How does R1 handle the route to network 10.1.80.0.0/24? (Exh...; Question 416: Where the output will be shown of the command debug conditio...; Question 417: Which two statements about VRRP object tracking are true? (C...; Question 418: A router receives a routing advertisement for the same prefi...; Question 419: What is the administrative distance for EBGP?...; Question 420: Which option to the command service timestamps debug enables...; Question 421: Under which circumstance will a branch ISR router contain in...; Question 422: Which two statements about password-protecting device access...; Question 423: A network engineer is configuring a solution to allow failov...; Question 424: Which command do you enter to filter only routing updates th...; Question 425: Which keyword of the aaa authentication ppp command supports...; Question 426: Refer to the exhibit. (Exhibit) Which one statement is true?...; Question 427: Which feature eliminates the need for Cisco Express Forwardi...; Question 428: What is supported RADIUS server? (Choose two)...; Question 429: Which two functionalities are specific to stateless NAT64? (...; Question 430: (Exhibit) The configuration of R1 to R6 are posted below for...; Question 431: Which value does a Cisco router use as its default username ...; Question 432: Which condition can cause unicast reverse path forwarding to...; Question 433: When unicast reverse path forwarding is configured on an int...; Question 434: Refer to the exhibit. Which interoperability technique imple...; Question 435: Refer to the exhibit. (Exhibit) On the basis of the partial ...; Question 436: What is the purpose of the route-target command?...; Question 437: (Exhibit) Refer to exhibit. A network engineer is unable to ...; Question 438: Refer to exhibit. A user calls from another branch office wi...; Question 439: Which statement about NTP authentication is true?...; Question 440: You get a call from a network administrator who tells you th...; Question 441: (Exhibit) What is the correct configuration to enable router...; Question 442: Which command denies the default route?...; Question 443: In IPv6, the interfaces running OSPF can be configured with ...; Question 444: What are three IPv6 transition mechanisms? (Choose three)...; Question 445: Which Netflow version supports MPLS?...; Question 446: The following exhibit shows ipv6 route output. What would th...; Question 447: Which option is the best for protecting CPU utilization on a...; Question 448: What happens when a router receives a packet with a TTL of 0...; Question 449: Refer to the exhibit. (Exhibit) Which technology can be empl...; Question 450: Which two statements are true about 6to4 tunnels? (Choose tw...; Question 451: (Exhibit) The configuration of R1 to R6 are posted below for...; Question 452: Which three benefits does the Cisco Easy Virtual Network pro...; Question 453: Which IOS commands can you use to limit the CPU impact of lo...; Question 454: When implementing OSPFv3, which statement describes the conf...; Question 455: A network engineer configured an IOS router to send syslog m...; Question 456: Refer to the exhibit. You notice that traffic from R1 to the...; Question 457: Which IPv4-mapped IPv6 address is equivalent to IPv6 address...; Question 458: Which DSL encapsulation method requires client software runn...; Question 459: A network engineer executes the show ip flow interface comma...; Question 460: Refer to the Exhibit. (Exhibit) Which statement about the co...; Question 461: A network engineer wants to baseline the network to determin...; Question 462: Refer to the exhibit. (Exhibit) R1 is configured with VRF-Li...; Question 463: Which two reductions are the correct reductions if the IPv6 ...; Question 464: In a comparison of an IPv4 header with an IPv6 header, which...; Question 465: Which address is an IPv6 multicast address?...; Question 466: Your Company trainee asks you, in the context of IPv6 and OS...; Question 467: What is the minimum level that displays a log message when a...; Question 468: To enable BGP tunneling over an IPv4 backbone, the IPv4 addr...; Question 469: Which statement is true about IPv6? Choose the best response...; Question 470: In which two areas does OSPF send a summary route by default...; Question 471: Other than a working EIGRP configuration, which option must ...; Question 472: How can you mitigate fragmentation issues between endpoints ...; Question 473: What command allows permit or deny IPv6 traffic?...; Question 474: IP SLA network with a configuration snippet...; Question 475: Where can NetFlow export data for long term storage and anal...; Question 476: A network engineer executes the show ip flow export command....; Question 477: What happens when two EIGRP peers have mismatched K values?...

Question 412/477

LEAVE A REPLY

Download PDF File