300-101 Exam Dumps | A customer requests policy-based routing. Packets arriving from source 209.165.200.225 should be sent

<< Prev Question Next Question >>

Question 237/477

A customer requests policy-based routing. Packets arriving from source 209.165.200.225 should be sent to the next hop at 209.165.200.227, with the precedence bit set to priority. Packets arriving from source
209.165.200.226 should be sent to the next hop at 209.165.200.228, with the precedence bit set to critical.
Which configuration completes these requirements?

A. access-list 1 permit 209.165.200.227
access-list 2 permit 209.165.200.228
!
route-map Texas permit 10
match ip address 1
set ip precedence priority
set ip next -hop 209.165.200.225
!

B. access-list 1 permit 209.165.200.228
access-list 2 permit 209.165.200.227
!
route-map Texas permit 10
match ip address 1
set ip precedence priority
set ip next -hop 209.165.200.226
!
route-map Texas permit 20
match ip address 2
set ip precedence critical
set ip next-hop 209.165.200.225
!
interface ethernet 1
ip policy route-map Texas

C. access-list 1 permit 209.165.200.225
access-list 2 permit 209.165.200.226
!
route-map Texas permit 10
match ip address 1
set ip precedence critical
set ip next -hop 209.165.200.227
!
route-map Texas permit 20
match ip address 2
set ip precedence priority
set ip next-hop 209.165.200.228
!
interface ethernet 1
ip policy route-map Texas

D. access-list 1 permit 209.165.200.225
access-list 2 permit 209.165.200.226
!
route-map Texas permit 10
match ip address 1
set ip precedence priority
set ip next -hop 209.165.200.227
!
route-map Texas permit 20
match ip address 2
set ip precedence critical
set ip next-hop 209.165.200.228
!
interface ethernet 1
ip policy route-map Texas

Question List (477q): Question 1: Refer to the exhibit. (Exhibit) After configuring the rotes,...; Question 2: Refer to the exhibit. (Exhibit) Network users on the 10.1.2....; Question 3: A network administrator notices that the BGP state and logs ...; Question 4: A network engineer is trying to modify an existing active NA...; Question 5: What is the reasons of command: router(config)# snmp-server ...; Question 6: A network engineer is notified that several employees are ex...; Question 7: The network engineer types the follow commands in a router: ...; Question 8: Which two methods of deployment can you use when implementin...; Question 9: Which two technologies can encapsulate an IPv6 payload in an...; Question 10: Which condition must be met before two EVN devices can conne...; Question 11: Which two OSPF router types can perform summarization in an ...; Question 12: Which type of address does OSPFv3 use to form neighbor adjac...; Question 13: Which command will display all the EIGRP feasible successor ...; Question 14: Which feature can mitigate fragmentation issues within netwo...; Question 15: Which two protocols are required for DMVPN? (Choose two.)...; Question 16: A network engineer is disabling split horizon on a point-to-...; Question 17: How should a router that is being used in a Frame Relay netw...; Question 18: Which two options can you use to configure an EIGRP stub rou...; Question 19: In SNMP v3, which security level provides encryption of the ...; Question 20: Refer to the exhibit. (Exhibit) Which statement about this n...; Question 21: How is authentication handled with OSPFv3? Select the best r...; Question 22: A network engineer wants to implement an SNMP notification p...; Question 23: Refer to the exhibit. You want router r1 to perform unequal-...; Question 24: Which two statements about EVN are true? (Choose two.)...; Question 25: Which Cisco IOS VPN technology leverages Ipsec, mGRE, dynami...; Question 26: Instructions: - Enter IOS commands on the device to verify n...; Question 27: A corporate policy requires PPPoE to be enabled and to maint...; Question 28: What is the NHRP role in DMVPN? (Choose two.)...; Question 29: Refer to the exhibit. (Exhibit) The excerpt was taken from t...; Question 30: The Cisco SA 500 Series Security Appliances are built specif...; Question 31: Which method allows IPv4 and IPv6 to work together without r...; Question 32: OSPF chooses routes in which order, regardless of route's ad...; Question 33: Which statement about the NPTv6 protocol is true?...; Question 34: When a new PC is connected to the network, which step must i...; Question 35: Which of the following is a GRE Tunnel characteristic?...; Question 36: The Neighbor Discovery Protocol in IPv6 replaces which proto...; Question 37: A network access server using TACACS+ for AAA operations rec...; Question 38: Which two features are provided by EIGRP for IPv6? (Choose t...; Question 39: Prior to enabling PPPoE in a virtual private dialup network ...; Question 40: Which criterion does BGP evaluate first when determining the...; Question 41: After testing various dynamic IPv6 address assignment method...; Question 42: An engineer is asked to monitor the availability of the next...; Question 43: Which two tasks must you perform when you install SSH on a C...; Question 44: Which LAN feature enables a default gateway to inform its en...; Question 45: Scenario You have been asked to evaluate an OSPF network set...; Question 46: Which two packet types can an EIGRP router send when a route...; Question 47: Refer to the exhibit. EIGRP is configured on all routers in ...; Question 48: By default, which statement is correct regarding the redistr...; Question 49: What is the effect of the following two commands? (Choose tw...; Question 50: A router with an interface that is configured with ipv6 addr...; Question 51: (Exhibit) Refer to the exhibit. A network engineer has confi...; Question 52: A company's corporate policy has been updated to require tha...; Question 53: A router is configured for redistribution to advertise EIGRP...; Question 54: Which three statements are true when configuring redistribut...; Question 55: In a point-to-multipoint Frame Relay topology, which two met...; Question 56: Refer to the exhibit. (Exhibit) Which statement is correct r...; Question 57: Which condition prevents the establishment of a DMVPN tunnel...; Question 58: Refer to the exhibit. (Exhibit) Which statement about the co...; Question 59: Refer to the exhibit. The network setup is running the RIP r...; Question 60: (Exhibit) Refer to the exhibit. All interfaces on each route...; Question 61: Which two commands must you configure in the calling router ...; Question 62: Which of the following are characteristics of TACACS+? (Choo...; Question 63: Which two LSA types were introduced to support OSPF for IPv6...; Question 64: Which Cisco VPN technology uses AAA to implement group polic...; Question 65: Refer to the exhibit. Which three NTP features can be deduce...; Question 66: Refer to exhibit. What is indicated by the show ip cef comma...; Question 67: (Exhibit) Refer to the exhibit. A network engineer is troubl...; Question 68: Which two tasks does a DHCP relay agent perform? (Choose two...; Question 69: What are the four main steps in configuring a GRE tunnel ove...; Question 70: Which option is one way to mitigate symmetric routing on an ...; Question 71: Which keyword of the aaa authentication ppp command applies ...; Question 72: Which protocol does VRF-Lite support?...; Question 73: What is the default OSPF hello interval on a Frame Relay poi...; Question 74: When a tunnel interface is configured in the default mode, w...; Question 75: A customer asks its service provider for VPN support IPv4 an...; Question 76: Which two features does RADIUS combine? (Choose two.)...; Question 77: An IPv6 overlay tunnel is required to communicate with isola...; Question 78: Which protocol can you use to remotely install an IOS on a C...; Question 79: Refer to the exhibit. configure terminal ip flow-export dest...; Question 80: Which three items can you track when you use two time stamps...; Question 81: Which two debug commands can you use to view issues with CHA...; Question 82: Which two statements about route targets that are configured...; Question 83: Refer to the exhibit. (Exhibit) A network administrator chec...; Question 84: Which two authentication protocols does PPP support? (Choose...; Question 85: The company network is in the process of migrating the IP ad...; Question 86: Refer to the exhibit. (Exhibit) Which statement about redist...; Question 87: Refer to the exhibit. Based upon the configuration, you need...; Question 88: A network engineer has configured a tracking object to monit...; Question 89: Which address is used by the Unicast Reverse Path Forwarding...; Question 90: Which IPV6 address type does RIPng use for next-hop addresse...; Question 91: Which algorithm is used by EIGRP to determine the best path ...; Question 92: Which outbound access list, applied to the WAN interface of ...; Question 93: Which NAT Command do you enter to disable dynamic ARP learni...; Question 94: Which option is a prerequisite for stateful NAT64?...; Question 95: Which two statements indicate a valid association mode for N...; Question 96: What command would you use to set EIGRP routes to be priorit...; Question 97: Which command must be globally enabled on a Cisco router to ...; Question 98: Which protocols support DMVPN?; Question 99: Which three functionalities are specific to stateful NAT64? ...; Question 100: Which problem can be caused by latency on a UDP stream?...; Question 101: What is VRF-Lite?; Question 102: Which two among the following are used to indicate external ...; Question 103: Which two statements about NTP stratum are true? (Choose two...; Question 104: Refer to the exhibit. (Exhibit) A network engineer receives ...; Question 105: What is true about EIGRP's redistributed static routes and s...; Question 106: A network engineer initiates the ip sla responder tcp-connec...; Question 107: Which CLI command can you enter to permit or deny IPv6 traff...; Question 108: Which NetFlow component is applied to an interface and colle...; Question 109: Which two statements are benefits of BGP peer groups? (Choos...; Question 110: A user is having issues accessing file shares on a network. ...; Question 111: Scenario You have been asked to evaluate an OSPF network set...; Question 112: When a packet is denied by an IPv6 traffic filter, which add...; Question 113: (Exhibit) A senior network engineer tries to propagate a sum...; Question 114: Which two EIGRP metrics have nonzero K values by default? (C...; Question 115: A network engineer wants to ensure an optimal end-to-end del...; Question 116: What are two important differences between OSPFv2 and OSPFv3...; Question 117: Which SNMP model and level can provide DES encryption?...; Question 118: Which two causes of latency are true? (Choose two.)...; Question 119: How does an EVN provide end-to-end virtualization and separa...; Question 120: Which option describes why the EIGRP neighbors of this route...; Question 121: Which two statements about NetFlow version 9 are true? (Choo...; Question 122: What is the default authentication in RIPv2 when authenticat...; Question 123: Using new backup router in spite of faulty one in ospf domai...; Question 124: A network engineer notices that transmission rates of sender...; Question 125: Refer to the exhibit. Which statement about the configuratio...; Question 126: Which IPv6 address type is seen as the next-hop address in t...; Question 127: A network engineer is configuring a routed interface to forw...; Question 128: What two situations could require the use of multiple routin...; Question 129: Which IP SLA deployment cycle reduces the deployment time fo...; Question 130: Which two statements about AAA implementation in a Cisco rou...; Question 131: Which LSA type on OSPFv3 is used for link-local updates?...; Question 132: A Network engineer wants to configure logging to compile and...; Question 133: What would you configure on SNMPv3 to allow authentication a...; Question 134: Which three functionalities are specific to stateful NAT64? ...; Question 135: Which three characteristics are shared by subinterfaces and ...; Question 136: Refer to the exhibit. The command is executed while configur...; Question 137: A network engineer wants to verify the status of a recently ...; Question 138: Refer to the exhibit. (Exhibit) A network engineer is modify...; Question 139: Which two statements about PAP and CHAP authentication are t...; Question 140: Which statement about dual stack is true?...; Question 141: Which Cisco VPN technology can use multipoint tunnel, result...; Question 142: Which feature can filter information at the interface level?...; Question 143: A network administrator is attempting to configure IP SLA to...; Question 144: OSPF routers that communicate with other network routers lik...; Question 145: Observe the exhibit. (Exhibit) If the command variance 3 wer...; Question 146: Which of the following are features of Netflow version 9?...; Question 147: You need the IP address of the devices with which the router...; Question 148: Refer to the exhibit. Which statement about the command outp...; Question 149: Which alerts will be seen on the console when running the co...; Question 150: Device R1 has 1 Gigabit and 10 Gigabit Ethernet interfaces. ...; Question 151: Which protocol is used in a DMVPN network to map physical IP...; Question 152: Which action can you take to mitigate unicast flooding in a ...; Question 153: Which two options are requirements for EIGRP authentication?...; Question 154: Scenario You have been asked to evaluate an OSPF network set...; Question 155: (Exhibit) The configuration of R1 to R6 are posted below for...; Question 156: Which IP SLA operation can be used to measure round-trip del...; Question 157: Which two statements about NTP operation are true? (Choose t...; Question 158: Refer to the following: Logging Console 7 Which option is on...; Question 159: Which two statement about GRE tunnel interface are true? (Ch...; Question 160: Which routing protocol does DMVPN support? (Choose three.)...; Question 161: (Exhibit) Which of the following is true?...; Question 162: Which technology does Easy Virtual Network use?...; Question 163: Various employees in the same department report to the netwo...; Question 164: Which two protocols are used to deploy a single Hub-DMVPN su...; Question 165: Which type of IPv6 address is an identifier for a single int...; Question 166: Which routing protocol routers traffic through the best path...; Question 167: Refer to the exhibit. (Exhibit) If this configuration is app...; Question 168: Refer to the exhibit. When summarizing these routes, which r...; Question 169: When an IPv6 enabled host boots, it sends a router solicitat...; Question 170: What is a valid ipv6 multicast address?...; Question 171: If you run the command auto-cost reference-bandwidth 10000 o...; Question 172: Which two statements about configuring Frame Relay point-to-...; Question 173: (Exhibit) Refer to the exhibit. Which statement describes th...; Question 174: Choose the best IP SLA deployment cycle that reduce deployme...; Question 175: Which two configurations can a PPPoE client support? (Choose...; Question 176: Which two statements about 6to4 tunneling are accurate? (Cho...; Question 177: A network administrator is troubleshooting a redistribution ...; Question 178: (Exhibit) Refer to the exhibit. Based on Cisco best practice...; Question 179: Which statement is true about the command ipv6 ospf 1 area 0...; Question 180: An engineer executes the ip flow ingress command in interfac...; Question 181: What are two limitations when in use of NPTv6 for IPV6 vs IP...; Question 182: What does the command show ip vrf purple TOPOLOGY shows?...; Question 183: Which statement describes the difference between a manually ...; Question 184: What is the function of the snmp-server manager command?...; Question 185: How to set up IP SLA to monitor Bandwidth between the certai...; Question 186: Using the rules for IPv6 addressing, how can the address 203...; Question 187: Refer to the exhibit. Which command would verify if PBR reac...; Question 188: Your network consists of a large hub-and-spoke Frame Relay n...; Question 189: Which command do you enter to display log messages with a ti...; Question 190: Which command should be added to RTB under router bgp 100 to...; Question 191: Which IPv6 address correctly compresses the IPv6 unicast add...; Question 192: Which two routers can do OSPF route summarization? (Choose t...; Question 193: A network administrator recently redistributed RIP routes in...; Question 194: Refer to the exhibit. Which option prevents routing updates ...; Question 195: A network administrator is troubleshooting a DMVPN setup bet...; Question 196: Refer to the exhibit. What two statements are true? (Choose ...; Question 197: When the tunnel interface is configured in default mode, whi...; Question 198: Refer to the exhibit. In the network diagram, Area 1 is defi...; Question 199: Refer to the exhibit. Will redistributed RIP routes from OSP...; Question 200: Which three configuration parameters can a DHCPV6 pool conta...; Question 201: Frame Relay LMI autosense. Which statements are true? (Choos...; Question 202: Which two BGP neighbor states are valid? (Choose two.)...; Question 203: Which next hop is going to be used for 172.17.1.0/24 ? (Exhi...; Question 204: Which functions are included in the two-message rapid exchan...; Question 205: What are three reasons to control routing updates via route ...; Question 206: What from the following can cause an issue for uRPF?...; Question 207: Consider this scenario. TCP traffic is blocked on port 547 b...; Question 208: A network engineer executes the commands logging host 172.16...; Question 209: What number is a valid representation for the 200F:0000:AB00...; Question 210: Refer to the exhibit. (Exhibit) Based on this FIB table, whi...; Question 211: (Exhibit) Based on the configuration information shown above...; Question 212: If you want to migrate an IS-IS network to another routing p...; Question 213: Which two protocols can be affected by MPP? (Choose two.)...; Question 214: What is a key benefit of using a GRE tunnel to provide conne...; Question 215: Refer to the exhibit. Which effect of this configuration is ...; Question 216: Refer to the exhibit. A new TAC engineer came to you for adv...; Question 217: Which statement about the split-horizon rule for distance ve...; Question 218: What does the show ip route vrf CISCO command display?...; Question 219: What is the default value of TCP maximum segment size?...; Question 220: What command can you enter to configure an enable password t...; Question 221: Which three statements about SNMP are true? (Choose three.)...; Question 222: The following configuration is applied to a router at a bran...; Question 223: Router E is configured with the EIGRP variance 2 command. (E...; Question 224: Refer to the exhibit. (Exhibit) Why is the default route not...; Question 225: Which routing protocol will continue to receive and process ...; Question 226: Which location is traffic from IP SLAs?...; Question 227: For security purposes, an Ipv6 traffic filter was configured...; Question 228: Which PPP authentication method sends authentication informa...; Question 229: A network engineer wants an NTP client to be able to update ...; Question 230: A company is deploying a multicast application that must be ...; Question 231: Which Cisco Express Forwarding table or tables hold forwardi...; Question 232: A network engineer is configuring two dedicated Internet con...; Question 233: Which two options are components of a dual stack? (Choose tw...; Question 234: What does the following access list, which is applied on the...; Question 235: Which statement is true about 6to4 tunneling?...; Question 236: (Exhibit) Refer to the exhibit. A network engineer is workin...; Question 237: A customer requests policy-based routing. Packets arriving f...; Question 238: Which option is one way to mitigate asymmetric routing on an...; Question 239: Refer to Exhibit. (Exhibit) Which two reasons for IP SLA tra...; Question 240: To configure SNMPv3 implementation, a network engineer is us...; Question 241: Refer to the exhibit. (Exhibit) Which command is used to con...; Question 242: Which Technology supports overlapping IP address on a single...; Question 243: A network administrator uses GRE over IPSec to connect two b...; Question 244: Which three protocols are supported with EVN? (Choose three....; Question 245: (Exhibit) Refer to the exhibit. Which networking challenge i...; Question 246: Which traffic does the following configuration allow? Ipv6 a...; Question 247: Router R1, a branch router, connects to the Internet using D...; Question 248: Refer to the exhibit. (Exhibit) R1 and R2 belong to the RIP ...; Question 249: (Exhibit) Which interoperability technique implemented on th...; Question 250: You are configuring a Microsoft client to call a PPP server ...; Question 251: What configurations does PPPoE allow? (Choose two.)...; Question 252: During a recent OSPF election among three routers, RTA was e...; Question 253: What do we prioritize with LLQ?...; Question 254: Which two GRE features can you configure to prevent fragment...; Question 255: When ospf is forming an adjacency, in which state does the a...; Question 256: Which two statements about NHRP in a DMVPN environment are t...; Question 257: Which statement describes what this command accomplishes whe...; Question 258: Which two types of threshold can you configure for tracking ...; Question 259: Windows Server Syslog blocked by ACL and....?...; Question 260: You have a router that has some interfaces configured with 1...; Question 261: You are configuring a static route. Which action must you ta...; Question 262: Which two options for authenticating a user who is attemptin...; Question 263: Which Cisco Express Forwarding components maintains Layer 2 ...; Question 264: Study this exhibit below carefully. (Exhibit) What is the ef...; Question 265: Which feature is supported with the PPPoE client?...; Question 266: Which three problems result from application mixing of UDP a...; Question 267: Which of the following NSAP addresses is a private, locally ...; Question 268: What are the three modes of Unicast Reverse Path Forwarding?...; Question 269: Refer to the exhibit. Router 1 cannot ping router 2 via the ...; Question 270: A company has their headquarters located in a large city wit...; Question 271: A network engineer configures two connected routers to run O...; Question 272: For a GRE tunnel to be up between two routers, which of the ...; Question 273: Refer to the exhibit. Which effect of this configuration is ...; Question 274: Which SNMP security level is available across all versions o...; Question 275: A network engineer needs to verify IP SLA operations on an i...; Question 276: Case study. (Exhibit) Some notices from above configuration:...; Question 277: An EUl-64 bit address is formed by inserting which 16-bit va...; Question 278: A network engineer executes the show ip cache flow command. ...; Question 279: What show command is used here? TCB Local Address Foreign Ad...; Question 280: Which configuration is applied to a device so that it blocks...; Question 281: Which two OSPF area types filter type 4 and type 5 LSAs? (Ch...; Question 282: A network engineer recently deployed Easy Virtual Networking...; Question 283: Refer to the exhibit. Which BGP attribute can be used to inf...; Question 284: The Dev-1 and Dev-3 routers are OSPF neighbors over the Ethe...; Question 285: Congestion in the network. What is the effect on UDP?...; Question 286: A network engineer is troubleshooting connectivity issues wi...; Question 287: Which two statements about VRF-Lite configurations are true?...; Question 288: A network engineer is asked to create an SNMP-enabled proact...; Question 289: Refer to the exhibit. (Exhibit) How would you confirm on R1 ...; Question 290: Which statement about stateless and stateful IPv6 autoconfig...; Question 291: An administrator types in the command router ospf 1 and rece...; Question 292: Which technology uses the many-to-one method of mapping IP a...; Question 293: Which value determines the amount of traffic that a network ...; Question 294: Which statement is true?; Question 295: Which two statements about GRE tunnel interfaces are true? (...; Question 296: Which two effects of asymmetric routing are true? (Choose tw...; Question 297: Which type of traffic does DHCP snooping drop?...; Question 298: Which statement is true about an IPsec/GRE tunnel?...; Question 299: Which two address types are included in NAT? (Choose two.)...; Question 300: Which three methods can a network engineer use to fix a metr...; Question 301: Refer to the exhibit. After configuring GRE between two rout...; Question 302: NPTv6 restrictions? (Choose all that apply.)...; Question 303: What is the viable successor of NAT_PT?...; Question 304: OSPF chooses routes in which order, regardless of route's ad...; Question 305: If you configure one router in your network with the auto-co...; Question 306: In which two ways can split horizon issues be overcome in a ...; Question 307: Which adverse circumstance can the TTL feature prevent?...; Question 308: Which feature is an invalid redistribute command option for ...; Question 309: Which statement about the use of tunneling to migrate to IPv...; Question 310: Which access list used to filter upper layer protocol?...; Question 311: Refer to the exhibit. (Exhibit) Which two statements are tru...; Question 312: Which technology is required on an EVN trunk interface?...; Question 313: Which two statements about EVNs are true? (Choose two.)...; Question 314: A network engineer wants to notify a manager in the event th...; Question 315: An administrator needs to setup an NTP client to provide upd...; Question 316: (Exhibit) How many times was SPF alrogithm executed on R4 fo...; Question 317: Which two statements about AAA with the local database are t...; Question 318: The OSPF database of a router shows LSA types 1, 2, 3, and 7...; Question 319: What is the maximum number of hops on a router that RIPng ad...; Question 320: Which BGP option is required when load sharing over multiple...; Question 321: Refer to the exhibit. Why is the 140.140.0.0 network not use...; Question 322: Refer to the exhibit. (Exhibit) How can you change this conf...; Question 323: Which type of message does a device configured with the eigr...; Question 324: Into which two types of areas would an area border router (A...; Question 325: You want to configure a device to select an OSPF-learned rou...; Question 326: How does an IOS router process a packet that should be switc...; Question 327: Which set of actions does a network engineer perform to set ...; Question 328: What happens when a router receives a route with an administ...; Question 329: RIPng ____________.; Question 330: Which command instruct a PPPoE client to obtain its IP addre...; Question 331: Which SNMP verification command shows the encryption and aut...; Question 332: Redistributing BGP into OSPF what statement is correct? rout...; Question 333: To enable policy-based routing, which function specifies the...; Question 334: (Exhibit) Refer to the exhibit. Which effect of this configu...; Question 335: What is the minimum privilege level to enter all commands in...; Question 336: What is true about peer groups? (Choose two.)...; Question 337: Which value does a point-to-point GRE tunnel use to identity...; Question 338: Which two statements about EVN are true? (Choose two.)...; Question 339: The Neighbor Discovery Protocol in ipv6 is replaced with whi...; Question 340: A router was configured with the eigrp stub command. The rou...; Question 341: Which three causes of unicast flooding are true? (Choose thr...; Question 342: Refer to the exhibit. Based on the output from the show comm...; Question 343: Which type of handshake does CHAP authentication use to esta...; Question 344: Which two statements about OSPF E1 routes are true? (Choose ...; Question 345: Which the Valid range for BGP private ASNs?...; Question 346: Which purpose of the AAA accounting feature is true when you...; Question 347: Which two tasks must you perform to configure a BGP peer gro...; Question 348: Which two commands must you configure on a DMVPN hub to enab...; Question 349: Refer to the exhibit. Which three statements accurately desc...; Question 350: (Exhibit) A network engineer is working on the network topol...; Question 351: Which IP SLA operation requires Cisco endpoints?...; Question 352: Scenario You have been asked to evaluate how EIGRP is functi...; Question 353: IP CEF load-sharing options (Choose three.)...; Question 354: Which authentication methods are EIGRP uses?...; Question 355: What does the following access list, which is applied on the...; Question 356: PPPoE requires certain signals and information to establish,...; Question 357: Which values identifies VPNs in an EVN environment?...; Question 358: What attribute is used to influce traffic form AS200 and AS3...; Question 359: When policy-based routing (PBR) is being configured, which t...; Question 360: Which two commands do you need to implement on a router to s...; Question 361: Which three statements about configuring OSPF in a IPv6 netw...; Question 362: Refer to the exhibit. Which two effects of this configuratio...; Question 363: Which command is needed to get the ip address assigned from ...; Question 364: Which command enables NAT-PT on an IPv6 interface?...; Question 365: Which functionality is required within an IP router that is ...; Question 366: Which mode of uRPF causes a router interface to accept a pac...; Question 367: Which three statements about IPv6 EIGRP are true? (Choose th...; Question 368: Which two statements are true of the OSPF link-state routing...; Question 369: Refer to the exhibit. (Exhibit) Which two statements are cor...; Question 370: Your company uses Voice over IP (VoIP). The system sends UDP...; Question 371: Users were moved from the local DHCP server to the remote co...; Question 372: Which statement about local policy routing is true?...; Question 373: Refer to the exhibit. (Exhibit) For which reason is EIGRP fa...; Question 374: If routers in a single area are configured with the same pri...; Question 375: Which three steps are most helpful in verifying proper route...; Question 376: Which two statements about DMVPN are true? (Choose two.)...; Question 377: When does a Cisco router send an ICMP redirect?...; Question 378: On which two types of interface is Frame Relay switching sup...; Question 379: Technologies used in preparing Service Provider IPv6? (Choos...; Question 380: Which statement best describes the following two OSPF comman...; Question 381: Which two statements about NetFlow templates are true? (Choo...; Question 382: A policy needs to be implemented on Router B so that any tra...; Question 383: Refer to the exhibit. (Exhibit) Which option represents the ...; Question 384: Which task must you perform to enable a point-to-point Frame...; Question 385: Which two types of authentication does EIGRP offer? (Choose ...; Question 386: What is a function of NPTv6?; Question 387: Ipv6 has just been deployed to all of the hosts within a net...; Question 388: Which command do you enter on router R6 so that BGP supports...; Question 389: Refer to the exhibit. (Exhibit) After configuring the rotes,...; Question 390: What are three key concepts that apply when configuring the ...; Question 391: Which STP feature can reduce TCNs on ports that are connecte...; Question 392: Refer to the exhibit. (Exhibit) Which option prevents routin...; Question 393: A route map was configured and it was distributing OSPF exte...; Question 394: What are the default timers for RIPng?...; Question 395: Which option is the minimum privilege level that allows the ...; Question 396: To configure 6to4 on a dual-stack edge router. Which three o...; Question 397: Which command creates a manual summary on an interface when ...; Question 398: What is show on logging console 7?...; Question 399: What is EIGRP Summary Route Administrative Distance?...; Question 400: What type of IPv6 packet will indicate traffic from single h...; Question 401: A network engineer executes the show ip sla statistics comma...; Question 402: Based on the configuration command below, which statement is...; Question 403: Refer to the exhibit. The DHCP client is unable to receive a...; Question 404: Which item does EIGRP IPv6 require before it can start runni...; Question 405: Which two commands do you need to implement on the CALLING r...; Question 406: Which are new LSA types in OSPF for IPv6 (OSPFv3)? (Choose t...; Question 407: What following parameters for the EIGRP authentication need ...; Question 408: Refer to the exhibit. (Exhibit) An engineer is enabling VPN ...; Question 409: What are 2 protocols used for user with authentication on ne...; Question 410: What appears in the other router routing table? #loopback EI...; Question 411: Which location within the network is preferred when using a ...; Question 412: If the total bandwidth is 64 kbps and the RTT is 3 seconds, ...; Question 413: Which three TCP enhancements can be used with TCP selective ...; Question 414: Refer to the exhibit. (Exhibit) After configuring the routes...; Question 415: How does R1 handle the route to network 10.1.80.0.0/24? (Exh...; Question 416: Where the output will be shown of the command debug conditio...; Question 417: Which two statements about VRRP object tracking are true? (C...; Question 418: A router receives a routing advertisement for the same prefi...; Question 419: What is the administrative distance for EBGP?...; Question 420: Which option to the command service timestamps debug enables...; Question 421: Under which circumstance will a branch ISR router contain in...; Question 422: Which two statements about password-protecting device access...; Question 423: A network engineer is configuring a solution to allow failov...; Question 424: Which command do you enter to filter only routing updates th...; Question 425: Which keyword of the aaa authentication ppp command supports...; Question 426: Refer to the exhibit. (Exhibit) Which one statement is true?...; Question 427: Which feature eliminates the need for Cisco Express Forwardi...; Question 428: What is supported RADIUS server? (Choose two)...; Question 429: Which two functionalities are specific to stateless NAT64? (...; Question 430: (Exhibit) The configuration of R1 to R6 are posted below for...; Question 431: Which value does a Cisco router use as its default username ...; Question 432: Which condition can cause unicast reverse path forwarding to...; Question 433: When unicast reverse path forwarding is configured on an int...; Question 434: Refer to the exhibit. Which interoperability technique imple...; Question 435: Refer to the exhibit. (Exhibit) On the basis of the partial ...; Question 436: What is the purpose of the route-target command?...; Question 437: (Exhibit) Refer to exhibit. A network engineer is unable to ...; Question 438: Refer to exhibit. A user calls from another branch office wi...; Question 439: Which statement about NTP authentication is true?...; Question 440: You get a call from a network administrator who tells you th...; Question 441: (Exhibit) What is the correct configuration to enable router...; Question 442: Which command denies the default route?...; Question 443: In IPv6, the interfaces running OSPF can be configured with ...; Question 444: What are three IPv6 transition mechanisms? (Choose three)...; Question 445: Which Netflow version supports MPLS?...; Question 446: The following exhibit shows ipv6 route output. What would th...; Question 447: Which option is the best for protecting CPU utilization on a...; Question 448: What happens when a router receives a packet with a TTL of 0...; Question 449: Refer to the exhibit. (Exhibit) Which technology can be empl...; Question 450: Which two statements are true about 6to4 tunnels? (Choose tw...; Question 451: (Exhibit) The configuration of R1 to R6 are posted below for...; Question 452: Which three benefits does the Cisco Easy Virtual Network pro...; Question 453: Which IOS commands can you use to limit the CPU impact of lo...; Question 454: When implementing OSPFv3, which statement describes the conf...; Question 455: A network engineer configured an IOS router to send syslog m...; Question 456: Refer to the exhibit. You notice that traffic from R1 to the...; Question 457: Which IPv4-mapped IPv6 address is equivalent to IPv6 address...; Question 458: Which DSL encapsulation method requires client software runn...; Question 459: A network engineer executes the show ip flow interface comma...; Question 460: Refer to the Exhibit. (Exhibit) Which statement about the co...; Question 461: A network engineer wants to baseline the network to determin...; Question 462: Refer to the exhibit. (Exhibit) R1 is configured with VRF-Li...; Question 463: Which two reductions are the correct reductions if the IPv6 ...; Question 464: In a comparison of an IPv4 header with an IPv6 header, which...; Question 465: Which address is an IPv6 multicast address?...; Question 466: Your Company trainee asks you, in the context of IPv6 and OS...; Question 467: What is the minimum level that displays a log message when a...; Question 468: To enable BGP tunneling over an IPv4 backbone, the IPv4 addr...; Question 469: Which statement is true about IPv6? Choose the best response...; Question 470: In which two areas does OSPF send a summary route by default...; Question 471: Other than a working EIGRP configuration, which option must ...; Question 472: How can you mitigate fragmentation issues between endpoints ...; Question 473: What command allows permit or deny IPv6 traffic?...; Question 474: IP SLA network with a configuration snippet...; Question 475: Where can NetFlow export data for long term storage and anal...; Question 476: A network engineer executes the show ip flow export command....; Question 477: What happens when two EIGRP peers have mismatched K values?...

Question 237/477

LEAVE A REPLY

Download PDF File