300-101 Exam Dumps | OSPF is enabled on router A You execute the following command on router A and receive the accompanying

<< Prev Question Next Question >>

Question 227/231

OSPF is enabled on router A You execute the following command on router A and receive the accompanying output:
RouterA#ping 224.0.0.5 repeat 1
Type escape sequence to abort.
Sending 1, 100-byte ICMP Echos to 224.0.0.5, timeout is 2 seconds:
Reply to request 0 from 10.100.100.1, 4 ms
10.100.100.1 is the IP address of a loopback interface on router A.
What can you conclude about router A?

A. Only the router A loopback interface is participating in the OSPF routing process.

B. None of the router A interfaces are participating in the OSPF routing process.

C. Router A is using the loopback interface IP address as its OSPF router ID.

D. Router A does not have any reachable OSPF neighbors.

Question List (231q): Question 1: Your network consists of a large hub-and-spoke Frame Relay n...; Question 2: What does the default value of the EIGRP variance command of...; Question 3: A corporate policy requires PPPoE to be enabled and to maint...; Question 4: Which PPP authentication method sends authentication informa...; Question 5: Which two actions must you perform to enable and use window ...; Question 6: You have implemented mutual route redistribution between OSP...; Question 7: Which two statements about route redistribution when impleme...; Question 8: Refer to the exhibit. (Exhibit) Network administrators have ...; Question 9: A company has just opened two remote branch offices that nee...; Question 10: What is the purpose of configuring the router as a PPPoE cli...; Question 11: Refer to the exhibit. EIGRP is configured with the default c...; Question 12: After DUAL calculations, a router has identified a successor...; Question 13: A network engineer is configuring a routed interface to forw...; Question 14: Refer to the exhibit. (Exhibit) When you examine the routing...; Question 15: Refer to the exhibit. (Exhibit) BigBids Incorporated is a wo...; Question 16: When troubleshooting an EIGRP connectivity problem, you noti...; Question 17: A network engineer executes the ipv6 flowset command. What i...; Question 18: Refer to the exhibit. (Exhibit) Which three commands should ...; Question 19: Which three TCP enhancements can be used with TCP selective ...; Question 20: ACME Rocket Sleds is growing, and so is their network. They ...; Question 21: Which Cisco IOS VPN technology leverages IPsec, mGRE, dynami...; Question 22: Refer to the exhibits. What can be done to fix the problem? ...; Question 23: Drag drop Select and Place: (Exhibit)...; Question 24: Refer to the exhibit. (Exhibit) What is the effect of the OS...; Question 25: You have been asked to evaluate how EIGRP is functioning in ...; Question 26: By default, which statement is correct regarding the redistr...; Question 27: What are the three modes of Unicast Reverse Path Forwarding?...; Question 28: Refer to the exhibit. (Exhibit) Router B is performing bidir...; Question 29: A packet capture log indicates that several router solicitat...; Question 30: Prior to enabling PPPoE in a virtual private dialup network ...; Question 31: Which NetFlow component is applied to an interface and colle...; Question 32: Refer to the exhibit. ROUTE.com is planning to implement a n...; Question 33: What is the international standard for transmitting data ove...; Question 34: Refer to the exhibit. (Exhibit) Which statement is correct r...; Question 35: Which three statements about OSPF areas are true? (Choose th...; Question 36: Refer to the exhibit. (Exhibit) A partial routing configurat...; Question 37: Refer to exhibit. (Exhibit) The exhibit shows R1 topology ta...; Question 38: Based on the exhibited output, (Exhibit) Which three stateme...; Question 39: During a redistribution of routes from OSPF into EIGRP, an a...; Question 40: Refer to the exhibit. (Exhibit) On the basis of the configur...; Question 41: What are two possible causes for EIGRP Stuck-In-Active route...; Question 42: Which configuration command is used to enable EIGRP unequal-...; Question 43: Which prefix is matched by the command ip prefix-list name p...; Question 44: Refer to the exhibit. (Exhibit) What happens when the router...; Question 45: Refer to the exhibit. (Exhibit) The partial configuration fo...; Question 46: A network engineer is trying to implement broadcast-based NT...; Question 47: Which switching method is used when entries are present in t...; Question 48: When an EIGRP topology change is detected, what is the corre...; Question 49: Which address is used by the Unicast Reverse Path Forwarding...; Question 50: Which EIGRP packet statement is true?...; Question 51: Refer to the exhibit. (Exhibit) ROUTE.com has just implement...; Question 52: Refer to the exhibit. (Exhibit) A Boston company bought the ...; Question 53: Refer to the exhibit. (Exhibit) Looking at the topology diag...; Question 54: Refer to the exhibit. (Exhibit) Which command only announces...; Question 55: You have been asked to evaluate how EIGRP is functioning in ...; Question 56: Refer to the exhibit. (Exhibit) EIGRP had converged in AS 1 ...; Question 57: Which of the below mentioned conditions form a neighbor rela...; Question 58: Which two statements about the EIGRP DUAL process are correc...; Question 59: A network engineer has been asked to ensure that the PPPoE c...; Question 60: Refer to the exhibit. (Exhibit) On all routers in the networ...; Question 61: The maximum number of routers per OSPF area typically depend...; Question 62: An engineer has added the following configuration snippet to...; Question 63: Refer to the following output: Router#showipnhrp detail 10.1...; Question 64: You have implemented mutual route redistribution between OSP...; Question 65: After implementing EIGRP on your network, you issue the show...; Question 66: Which type of traffic does DHCP snooping drop?...; Question 67: You have been asked to evaluate how EIGRP is functioning in ...; Question 68: Refer to the exhibit. (Exhibit) Routers R1 and R2 are runnin...; Question 69: The Cisco SA 500 Series Security Appliances are built specif...; Question 70: A network engineer notices that transmission rates of sender...; Question 71: Refer to the exhibit. (Exhibit) R1 and R2 have been configur...; Question 72: What is the default OSPF hello interval on a Frame Relay poi...; Question 73: Refer to the exhibit. (Exhibit) All EIGRP load balancing par...; Question 74: ROUTE.com is a small IT corporation that has an existing ent...; Question 75: When implementing OSPFv3, which statement describes the conf...; Question 76: A company's corporate policy has been updated to require tha...; Question 77: Refer to the following access list. access-list 100 permit i...; Question 78: What does the following access list, which is applied on the...; Question 79: What is a function of NPTv6?; Question 80: After implementing EIGRP on your network, you issue the show...; Question 81: What is the purpose of the autonomous-system {autonomous-sys...; Question 82: Refer to the exhibit. Two routers are connected by Frame Rel...; Question 83: Which three statements are true about EIGRP operation? (Choo...; Question 84: Refer to the exhibit. (Exhibit) Which three statements are t...; Question 85: Scenario: You have been asked to evaluate an OSPF network se...; Question 86: A network engineer is notified that several employees are ex...; Question 87: Given the following partial configuration for Router A: inte...; Question 88: Refer to the exhibit. (Exhibit) You are the network administ...; Question 89: A network engineer executes the show crypto ipsecsa command....; Question 90: Refer to the exhibit. (Exhibit) A network administrator chec...; Question 91: Refer to the exhibits. Router B should advertise the network...; Question 92: Refer to the exhibit. OSPF is configured on all routers in t...; Question 93: When using SNMPv3 with NoAuthNoPriv, which string is matched...; Question 94: An organization decides to implement NetFlow on its network ...; Question 95: Under which condition does UDP dominance occur?...; Question 96: Which of the below mentioned conditions form a neighbor rela...; Question 97: Refer to the exhibit. ROUTE.com is planning to implement a s...; Question 98: A network administrator is managing a hub-and-spoke network ...; Question 99: After you review the output of the command show ipv6 interfa...; Question 100: The administrator wants to verify the current state of the O...; Question 101: Refer to the exhibit. (Exhibit) Routers R1 and R2 have estab...; Question 102: In which state do DR and BDR establish adjacency with each O...; Question 103: Which two types of routes will be advertised with the EIGRP ...; Question 104: IPv6 has just been deployed to all of the hosts within a net...; Question 105: Refer to the exhibit. (Exhibit) You are the network administ...; Question 106: A network engineer initiates the ipsla responder tcp-connect...; Question 107: Refer to the exhibit. (Exhibit) ROUTE Enterprises has many s...; Question 108: Refer to the exhibit. (Exhibit) The actual speed of the seri...; Question 109: Refer to the exhibit. (Exhibit) EIGRP is configured on all r...; Question 110: You are a network technician, study the exhibit carefully. (...; Question 111: Refer to the exhibit. You have completed an OSPF implementat...; Question 112: A network administrator executes the command clear ip route....; Question 113: You have completed an OSPF implementation, and you are verif...; Question 114: Which statement is true about OSPF Network LSAs?...; Question 115: During the redistribution process configured on RTA, some of...; Question 116: Refer to the exhibit. (Exhibit) Routers R1 and R2 have been ...; Question 117: Refer to the following. Router # sh ip route eigrp 13.0.0.0/...; Question 118: A network engineer is asked to configure a "site-to-site" IP...; Question 119: Identify three characteristics of EIGRP feasible successors?...; Question 120: Refer to the exhibit. (Exhibit) Which two statements are tru...; Question 121: Which of the following are methods EIGRP uses to initially p...; Question 122: Which protocol uses dynamic address mapping to request the n...; Question 123: What is a key benefit of using a GRE tunnel to provide conne...; Question 124: A network administrator is troubleshooting an EIGRP connecti...; Question 125: Refer to the exhibit. (Exhibit) Based on this FIB table, whi...; Question 126: For a GRE tunnel to be up between two routers, which of the ...; Question 127: When other routing protocol routes are being redistributed i...; Question 128: Refer to the Exhibit. (Exhibit) Routers in the Diagram are c...; Question 129: Which two functions are completely independent when implemen...; Question 130: Which of the following settings could prevent two potential ...; Question 131: A network engineer is configuring SNMP on network devices to...; Question 132: Which two statements are true about EIGRP manual summarizati...; Question 133: For troubleshooting purposes, which method can you use in co...; Question 134: You have been asked to evaluate how EIGRP is functioning in ...; Question 135: Refer to the exhibit. OSPF is running throughout the network...; Question 136: Refer to the exhibit and the partial configuration on router...; Question 137: Refer to the exhibit. (Exhibit) ROUTE.com is planning to imp...; Question 138: Which statement is true about the PPP Session Phase of PPPoE...; Question 139: Which statement about the use of tunneling to migrate to IPv...; Question 140: Which common issue causes intermittent DMVPN tunnel flaps?...; Question 141: Refer to the exhibit. (Exhibit) Router RTA is the hub router...; Question 142: Which encapsulation supports an interface that is configured...; Question 143: To make OSPF area 4 a totally stubby area, which two things ...; Question 144: When verifying the OSPF link state database, which type of L...; Question 145: Refer to the exhibit. (Exhibit) Which statement about the ou...; Question 146: When configuring EIGRP to run across a 56 Kbps serial PPP li...; Question 147: Refer to the exhibit. (Exhibit) R1 accesses the Internet usi...; Question 148: Refer to the exhibit. (Exhibit) A Boston company bought the ...; Question 149: After a recent DoS attack on a network, senior management as...; Question 150: Refer to the diagram. Which OSPF configuration command is re...; Question 151: Refer to the exhibit. Router B and router C are performing m...; Question 152: Which traffic does the following configuration allow? ipv6 a...; Question 153: Refer to the exhibit. (Exhibit) Examine the partial configur...; Question 154: A network engineer finds that a core router has crashed with...; Question 155: How is authentication handled with OSPFv3?...; Question 156: Refer to the output. (Exhibit) What IOS command produces thi...; Question 157: For security purposes, an IPv6 traffic filter was configured...; Question 158: Refer to exhibit. (Exhibit) RouterA (DR) failed, and after 1...; Question 159: What is the result of the command ip flow-export destination...; Question 160: If the primary path goes down, what will EIGRP use to reach ...; Question 161: Study the exhibit carefully. (Exhibit) Router R1 is connecte...; Question 162: Scenario: You have been asked to evaluate an OSPF network se...; Question 163: Which two routing interface parameters are supported in OSPF...; Question 164: Which method allows IPv4 and IPv6 to work together without r...; Question 165: A network administrator uses IP SLA to measure UDP performan...; Question 166: You have been asked to evaluate how EIGRP is functioning in ...; Question 167: When verifying OSPF virtual link problems, which is an impor...; Question 168: A network engineer is configuring a solution to allow failov...; Question 169: PPPoE is composed of which two phases?...; Question 170: Refer to the exhibit. (Exhibit) BigBids Incorporated is a wo...; Question 171: EIGRP has been configured to operate over Frame Relay multip...; Question 172: Exhibit: (Exhibit) Refer to the topology diagram R3 is redis...; Question 173: When an OSPF design is planned, which implementation can hel...; Question 174: Refer to the exhibit. EIGRP has been configured on routers R...; Question 175: Which command displays the number of times that the OSPF Sho...; Question 176: You are troubleshooting an OSPF problem where external route...; Question 177: Which two methods use IPsec to provide secure connectivity f...; Question 178: A network engineer executes the show ip flow export command....; Question 179: You want the redistributed EIGRP AS 10 routes to have an adm...; Question 180: Router R1, a branch router, connects to the Internet using D...; Question 181: Examine the exhibit carefully. (Exhibit) EIGRP is configured...; Question 182: Which DSL encapsulation method requires client software runn...; Question 183: Which three problems result from application mixing of UDP a...; Question 184: Which two methods of deployment can you use when implementin...; Question 185: Which two routing protocols require a metric to be configure...; Question 186: S Industries has expanded their business with the addition o...; Question 187: Refer to the exhibit. Router C was configured so that it cou...; Question 188: Refer to the exhibit. (Exhibit) The Route.com company is run...; Question 189: Refer to the exhibit. (Exhibit) A network administrator want...; Question 190: Refer to the exhibit. (Exhibit) A company would prefer all I...; Question 191: What administrative distance is given to EIGRP summary route...; Question 192: You have just completed an OSPF implementation. While execut...; Question 193: Given the accompanying output, which additional command is n...; Question 194: Router A and Router B are configured with IPv6 addressing an...; Question 195: Which three statements about the EIGRP routing protocol are ...; Question 196: The Dev-1 and Dev-3 routers are OSPF neighbors over the Ethe...; Question 197: Refer to the exhibit. (Exhibit) The routing protocols EIGRP ...; Question 198: A router with an interface that is configured with ipv6 addr...; Question 199: Refer to the exhibit. (Exhibit) In a redundant hub-and-spoke...; Question 200: What are three key concepts that apply when configuring the ...; Question 201: Route.com is a small IT corporation that is attempting to im...; Question 202: Refer to the exhibit. (Exhibit) EIGRP has been configured on...; Question 203: Which three characteristics are shared by subinterfaces and ...; Question 204: Based on the exhibited output, which three statements are tr...; Question 205: In EIGRP, when the IP default-network command is configured ...; Question 206: You are a network engineer with ROUTE.com, a small IT compan...; Question 207: You are a network engineer with ROUTE.com, a small IT compan...; Question 208: An engineer has configured a router to use EUI-64, and was a...; Question 209: Refer to the following command: router(config)# ip http secu...; Question 210: Which are three features of EIGRP? (Choose three)...; Question 211: Based on the need to limit processing and bandwidth utilizat...; Question 212: Refer to the exhibit. (Exhibit) Which statement about dynami...; Question 213: Your network has a mixture of Fast Ethernet and Gigabit Ethe...; Question 214: Refer to the exhibit. The network administrator is trying to...; Question 215: A stub area is typically created using what kind of topology...; Question 216: Which statement about a non-zero value for the load metric (...; Question 217: A user is having issues accessing file shares on a network. ...; Question 218: Refer to the exhibit. EIGRP has been configured on all route...; Question 219: Refer to the exhibit. Which two Cisco IOS commands on R2 wou...; Question 220: Refer to the exhibit. (Exhibit) Which router configuration c...; Question 221: Scenario: You have been asked to evaluate an OSPF network se...; Question 222: Refer to the exhibit. (Exhibit) Which one statement is true?...; Question 223: The following command was issued on R2 (Exhibit) Given the a...; Question 224: Which show command will display only the Type 5 LSAs in the ...; Question 225: RouterA# ~~~~~ ! router ospf 1 log-adjacency-changes network...; Question 226: Scenario: You have been asked to evaluate an OSPF network se...; Question 227: OSPF is enabled on router A You execute the following comman...; Question 228: A network engineer has left a NetFlow capture enabled over t...; Question 229: Refer to the exhibit. Why are the EIGRP neighbors for this r...; Question 230: Refer to the exhibit. (Exhibit) A new TAC engineer came to y...; Question 231: Refer to the exhibit. (Exhibit) EIGRP has been configured on...

Question 227/231

LEAVE A REPLY

Download PDF File