200-105 Exam Dumps | What command is used to verify the DLCI destination address in a Frame Relay static configuration?

<< Prev Question Next Question >>

Question 36/383

What command is used to verify the DLCI destination address in a Frame Relay static configuration?

A. show frame-relay pvc

B. show frame-relay lmi

C. show frame-relay map

D. show frame relay end-to-end

Question List (383q): Question 1: Which feature can you implement to reserve bandwidth for voi...; Question 2: Which BGP command do you enter to allow a device to exchange...; Question 3: Which command can you enter in a network switch configuratio...; Question 4: Which two pieces of information are provided by the show con...; Question 5: Which statement about using the keepalive command on a tunne...; Question 6: What is the default administrative distance of OSPF?...; Question 7: What is the minimum command to turn on encryption on SNMP?...; Question 8: Refer to the exhibit. Router4 can ping Router5 (172.16.6.5),...; Question 9: Which two actions must you take to configure a static EtherC...; Question 10: Which option is the benefit of implementing an intelligent D...; Question 11: Which two statements about LACP are true? (Choose two.)...; Question 12: Refer to the exhibit. A network associate has configured OSP...; Question 13: A network administrator enters the following command on a ro...; Question 14: Which command do you enter to determine the root priority?...; Question 15: What information does a router running a link-state protocol...; Question 16: Which statement describes VRRP object tracking?...; Question 17: Which two of these statements are true of IPv6 address repre...; Question 18: Which two features are compatible with SPAN sessions? (Choos...; Question 19: Refer to the exhibit. What is the most appropriate summariza...; Question 20: Which protocol authenticates connected devices before allowi...; Question 21: Which interface counter can you use to diagnose a duplex mis...; Question 22: Which command can you enter on a switch to determine the cur...; Question 23: Refer to the graphic. Users on the Holyoke router are unable...; Question 24: Which two statements about interior gateway routing protocol...; Question 25: How does using the service password-encryption command on a ...; Question 26: An administrator is troubleshooting a problem between router...; Question 27: Which statement about GRE tunnels is true?...; Question 28: Refer to the exhibit. Host A has tested connectivity to a re...; Question 29: Which two statements describe the process identifier that is...; Question 30: Which configuration can you apply to enable encapsulation on...; Question 31: Scenario Refer to the topology. Your company has decided to ...; Question 32: Which result occurs when you configure the switchport mode d...; Question 33: Which mode is compatible with Trunk, Access, and desirable p...; Question 34: Which value can you modify to configure a specific interface...; Question 35: Which command must you enter to prepare an interface to carr...; Question 36: What command is used to verify the DLCI destination address ...; Question 37: Which technology can prevent client devices from arbitrarily...; Question 38: Which QoS feature can change the value of the IPv4 Type of S...; Question 39: Which purpose of the network command in the BGP configuratio...; Question 40: Which statement about slow inter-VLAN forwarding is true?...; Question 41: Scenario Refer to the topology. Your company has decided to ...; Question 42: Refer to the exhibit. A technician pastes the configurations...; Question 43: If primary and secondary root switches with priority 16384 b...; Question 44: Refer to the exhibit. How should Switch1 and Switch2 be conn...; Question 45: Refer to the exhibit. Assuming that the entire network topol...; Question 46: Which command helps a network administrator to manage memory...; Question 47: Which two options are valid WAN connectivity methods? (Choos...; Question 48: Refer to the exhibit. Which statement describes DLCI 17? (Ex...; Question 49: Which command can you enter to assign an interface to the de...; Question 50: Which three options are the HSRP states for a router? (Choos...; Question 51: Which two privileged mode Cisco IOS commands can be used to ...; Question 52: Refer to the exhibit. Hosts in network 192.168.2.0 are unabl...; Question 53: Which option is the industry-standard protocol for Etherchan...; Question 54: Which three options are types of Layer 2 network attack? (Ch...; Question 55: Which two switch states are valid for 802.1w? (Choose two.)...; Question 56: Which three components must you configure to establish a GRE...; Question 57: Which command should you enter to allow carrying voice?...; Question 58: It has become necessary to configure an existing serial inte...; Question 59: When are packets processed by an inbound access list?...; Question 60: Which command do you enter to protect a PortFast-enabled por...; Question 61: Which two types of cloud services may require you to alter t...; Question 62: The ROUTE company has a small network. The network consists ...; Question 63: Which command do you enter to verify that a VLAN has been re...; Question 64: When troubleshooting Ethernet connectivity issues how can yo...; Question 65: Which Layer 2 protocol encapsulation type supports synchrono...; Question 66: What Cisco IOS feature can be enabled to pinpoint an applica...; Question 67: A network administrator needs to allow only one Telnet conne...; Question 68: In a GLBP network, who is responsible for the arp request?...; Question 69: What is the default Syslog facility level?...; Question 70: When is the most appropriate time to escalate an issue that ...; Question 71: In which two ways can you isolate the location of a connecti...; Question 72: After you notice that the SNMP manager is failing to receive...; Question 73: Which Cisco IOS feature can you use to dynamically identify ...; Question 74: Which technology supports fast provisioning for cloud resour...; Question 75: Which command do you enter to enable local authentication fo...; Question 76: Which protocol provides a method of sharing VLAN configurati...; Question 77: To which two categories of routing protocols does BGP belong...; Question 78: Refer to the exhibit. Which switch provides the spanning-tre...; Question 79: Refer to the exhibit. At the end of an RSTP election process...; Question 80: Which three options are types of slow VLAN connectivity? (Ch...; Question 81: Which result occurs when you configure the standby preempt c...; Question 82: What are three factors a network administrator must consider...; Question 83: What do SNMPv1 and SNMPv2 have in common?...; Question 84: A router has been configured to provide the nine users on th...; Question 85: Refer to the exhibit. (Exhibit) Router edge-1 is unable to e...; Question 86: What is the minimum level of SNMP that provides encryption?...; Question 87: Identify the four valid IPv6 addresses. (Choose four.)...; Question 88: Refer to the exhibit. How should the FastEthernet0/1 ports o...; Question 89: What is true about Ethernet? (Choose two.)...; 2 commentQuestion 90: Instructions Enter Cisco IOS commands on device to verify ne...; 1 commentQuestion 91: While troubleshooting the failure of an OSPFv3 Ethernet conn...; Question 92: Which command can be used from a PC to verify the connectivi...; Question 93: Disadvantages of using proxy ARP?...; Question 94: What are three advantages of vlans? (Choose three.)...; Question 95: Which two characteristics of stacked switches are true? (Cho...; Question 96: Which statement about STP root bridges is true?...; Question 97: Scenario Refer to the topology. Your company has decided to ...; Question 98: What are two enhancements that OSPFv3 supports over OSPFv2? ...; Question 99: The network administrator of the Oregon router adds the foll...; Question 100: Which IEEE standard does PVST+ use to tunnel information?...; Question 101: Which two statements about traffic shaping are true? (Choose...; Question 102: Which command do you enter to allow a new VLAN across a trun...; Question 103: Refer to the exhibit. If the router Cisco returns the given ...; Question 104: How does a router handle an incoming packet whose destinatio...; 1 commentQuestion 105: Instructions: Enter IOS commands on the Dubai router to veri...; Question 106: Refer to the exhibit. Which of these correctly describes the...; Question 107: Which three statements about the features of SNMPv2 and SNMP...; Question 108: In an HSRP failover environment, which two tasks must you pe...; Question 109: Which three statements are benefits of using a shadow router...; Question 110: At which layer of the OSI model does PPP perform?...; 1 commentQuestion 111: Which configuration enables OSPF for network 192.168.1.0/24?...; Question 112: Which two of these statements regarding RSTP are correct? (C...; Question 113: Refer to the exhibit. HostA cannot ping HostB. Assuming rout...; Question 114: What is a valid HSRP virtual MAC address?...; Question 115: Which WAN topology is most appropriate for a centrally locat...; Question 116: Refer to the exhibit. If the router R1 returns the given out...; Question 117: Refer to the exhibit. Some 2950 series switches are connecte...; Question 118: Which protocol supports sharing the VLAN configuration betwe...; Question 119: You are working in a data center environment and are assigne...; Question 120: Which statement about access lists that are applied to an in...; Question 121: Which statement about OSPFv3 configuration is true?...; Question 122: Refer to the exhibit. On R1 which routing protocol is in use...; 1 commentQuestion 123: Under normal operations, Cisco recommends that you configure...; Question 124: Refer to the exhibit. A frame on VLAN 1 on switch S1 is sent...; Question 125: Which type of topology is required by DMVPN?...; Question 126: What is the first step you perform to configure an SNMPv3 us...; Question 127: Which encapsulation type is a Frame Relay encapsulation type...; Question 128: Refer to the exhibit. What is the meaning of the term dynami...; Question 129: Which switch port mode prevents DTP frames from being sent?...; Question 130: A router has learned three possible routes that could be use...; Question 131: Refer to the exhibit. All three PCs on the network are in di...; Question 132: Instructions This item contains several questions that you m...; Question 133: Refer to the output from the show running-config command in ...; Question 134: Which two statements about using the CHAP authentication mec...; Question 135: In the Software-Defined Networking model, where is the inter...; Question 136: What does the "Inside Global" address represent in the confi...; Question 137: Refer to the topology and partial router configurations show...; Question 138: Which type of IPv6 ACL is applied first in the order of prec...; Question 139: Which commands are required to properly configure a router t...; Question 140: What are three valid reasons to assign ports to VLANs on a s...; Question 141: Which three statements about VTP features are true? (Choose ...; Question 142: Which two functions of the APIC-EM Path Trace ACL Analysis t...; Question 143: Which two protocols can detect native vlan mismatch errors? ...; Question 144: Which function does traffic shaping perform?...; Question 145: Which two Cisco IOS commands, used in troubleshooting, can e...; Question 146: What 8-bit field exists in IP packet for QoS?...; Question 147: Which statement about VLAN configuration is true?...; Question 148: Which role is used by VLAN 1 by default?...; Question 149: Which port type is used in a stacked deployment?...; Question 150: What OSPF command, when configured, will include all interfa...; Question 151: Which QoS prioritization method is most appropriate for inte...; Question 152: Which statement about MPLS is true?...; Question 153: Which command do you enter to configure client authenticatio...; Question 154: Which option is the main function of congestion management?...; Question 155: Which three elements must be used when you configure a route...; Question 156: You attempt to execute the APIC-EM ACL path trace feature wi...; Question 157: Refer to the exhibit. What does STATUS=ACTIVE refer to in th...; Question 158: A router receives information about network 192.168.10.0/24 ...; Question 159: When you deploy multilink PPP on your network, where must yo...; Question 160: Which networking function occurs on the data plane?...; Question 161: Which effect of the monitor session 16 source interface giga...; Question 162: For which type of connection is broadband PPPoE most appropr...; Question 163: Which device classes are used over serial links? (Choose two...; Question 164: What can cause two OSPF neighbors to be stuck in the EXSTART...; Question 165: Which three features are added in SNMPv3 over SNMPv2? (Choos...; Question 166: If host Z needs to send data through router R1 to a storage ...; Question 167: Which two features are supported only in named access lists?...; Question 168: Which three checks must you perform when troubleshooting EIG...; Question 169: Refer to the exhibit. What can be concluded from the output ...; Question 170: Which protocol can be used between administrative domains?...; Question 171: By default, which two K values does EIGRP for IPv6 use to ca...; Question 172: Refer to the exhibit. A packet with a source IP address of 1...; Question 173: Refer to the graphic and routing table for router R1. Based ...; Question 174: Workstation A has been assigned an IP address of 192.0.2.24/...; Question 175: Which two statements about static NAT translations are true?...; Question 176: A network administrator needs to configure a serial link bet...; Question 177: Instructions: Enter IOS commands on the Dubai router to veri...; Question 178: Which tool or utility can report whether traffic matching sp...; Question 179: Which command do you enter to verify an SVI?...; Question 180: In which configuration can a PPPoE client operate normally?...; Question 181: What does it take for BGP to establish connection? (Choose t...; Question 182: Refer to the exhibit. Which statement is true? (Exhibit)...; 1 commentQuestion 183: Refer to the exhibit. Which command do you enter so that R1 ...; Question 184: Refer to the exhibit. Which two statements are true about th...; Question 185: Refer to the exhibit. The output that is shown is generated ...; Question 186: VLAN 3 is not yet configured on your switch. What happens if...; Question 187: Which state does a port with BPDU guard enabled enter when i...; Question 188: Which VLAN bridge priority value will make a switch as root ...; Question 189: Which three features are supported when you use TACACS+ for ...; Question 190: Which programming language do you use to script interactions...; Question 191: In which three circumstances may your organization require a...; Question 192: Which command do you enter to configure local authentication...; Question 193: Which two actions must you take to configure a PAgP Ethernet...; Question 194: While you were troubleshooting a connection issue, a ping fr...; Question 195: What does split horizon prevent?...; Question 196: Refer to the exhibit. After you apply the give configuration...; Question 197: Which utility do you use to view IP traffic that is switched...; Question 198: The output of the show frame-relay pvc command shows "PVC ST...; Question 199: Which command do you enter to enable an interface to support...; Question 200: What is the best way to verify that a host has a path to oth...; Question 201: Instructions Enter Cisco IOS commands on device to verify ne...; Question 202: Which protocol is a Cisco proprietary implementation of STP?...; Question 203: Which two statements identify differences between single-hom...; Question 204: Which three describe the reasons large OSPF networks use a h...; Question 205: Refer to the exhibit. A junior network engineer has prepared...; Question 206: What is one benefit of PVST+?; Question 207: When you configure a new switch interface, to which VLAN it ...; Question 208: Which option describes a difference between EIGRP for IPv4 a...; Question 209: What is the default VLAN on an access port?...; Question 210: Which interior routing protocol reduces the size of route ta...; Question 211: Which two statements about switch stacking are true? (Choose...; Question 212: Scenario Refer to the topology. Your company has connected t...; Question 213: Refer to the exhibit. Which route will be found in the routi...; Question 214: Which WAN topology has the highest degree of reliability?...; Question 215: In which solution is a router ACL used?...; Question 216: Refer to the exhibit. Which subnet mask will place all hosts...; Question 217: Refer to the exhibit. How many interfaces on R1 should be co...; Question 218: Which channel mode is available to static EhterChannels?...; Question 219: Which switch architecture is scalable, flexible, resilient, ...; Question 220: Which command enables IPv6 forwarding on a Cisco router?...; Question 221: Refer to the exhibit. What command sequence will enable PAT ...; Question 222: What occurs on a Frame Relay network when the CIR is exceede...; Question 223: Which pairing reflects a correct protocol-and-metric relatio...; Question 224: What is the default DTP mode on a switch port?...; Question 225: Which two protocols can support trunking? (Choose two.)...; Question 226: Refer to the exhibit. Which address range efficiently summar...; Question 227: Which three protocols does APIC-EM support with Path Trace? ...; Question 228: Which technology supports multiple dynamic secure connection...; Question 229: How can you manually configure a switch so that it is select...; Question 230: Host is able to ping a web server but it is not able to do H...; Question 231: When you enable PortFast on a switch port, the port immediat...; Question 232: Which statements are true about EIGRP successor routes? (Cho...; Question 233: Which two data link layers are supported by Cisco IOS Softwa...; Question 234: Which statement about switch access ports is true?...; Question 235: Refer to the exhibit. Which two statements about the configu...; Question 236: The command frame-relay map ip 10.121.16.8 102 broadcast was...; Question 237: Which two steps must you perform on each device that is conf...; Question 238: Which set of commands is recommended to prevent the use of a...; Question 239: Which three effects of using local SPAN are true? (Choose th...; Question 240: Refer to the exhibit. The network shown in the exhibit has j...; Question 241: Which Layer 2 attack is specifically mitigated by changing t...; Question 242: Refer to the exhibit. To what does the 128 refer in the rout...; Question 243: Which protocol can cause overload on a CPU of a managed devi...; Question 244: What type of attack is when trusted source replace mac table...; Question 245: Which information is provided by the output of the show snmp...; Question 246: Instructions This item contains several questions that you m...; Question 247: Which options are the two differences between HSRP versions ...; Question 248: Which term describes a spanning-tree network that has all sw...; Question 249: For which reason can OSPFv3 fail to start between two router...; Question 250: Which type does a port become when it receives the best BPDU...; Question 251: Refer to the exhibit. The network is converged. After link-s...; Question 252: The internetwork infrastructure of company XYZ consists of a...; Question 253: Which protocol provides a method of sharing VLAN configurati...; Question 254: Which combination of values is valid for a router-on-a-stick...; Question 255: What is the alert message generated by SNMP agents called? (...; Question 256: Which feature does PPP use to encapsulate multiple protocols...; Question 257: Which two statements about exterior gateway routing protocol...; Question 258: Refer to the exhibit. Host A pings interface S0/0 on router ...; Question 259: Which two statements about the spanning-tree bridge ID are t...; Question 260: Refer to the exhibit. Assume that all of the router interfac...; Question 261: Which feature would prevent a workstation from receiving a D...; Question 262: Which command do you enter to determine the status of the SV...; Question 263: Which two statements about VLAN port assignment are true? (C...; Question 264: Which command reveals the last method used to powercycle a r...; Question 265: Which configuration do you apply to an HSRP router so that i...; Question 266: What are OSPF's default hello and dead timers? (Choose two)...; Question 267: What are three reasons that an organization with multiple br...; Question 268: Refer to the exhibit. Based on the exhibited routing table, ...; Question 269: Which three statements about DTP are true? (Choose three.)...; Question 270: Refer to the exhibit. Why has this switch not been elected t...; Question 271: Which function is performed by a TACACS+ server?...; Question 272: Refer to the exhibit. Each of these four switches has been c...; Question 273: Which type of routing protocol uses the Bellman-Ford algorit...; Question 274: The network administrator is asked to configure 113 point-to...; Question 275: Which option describes a benefit of a point-to-point leased ...; Question 276: Which command is used to enable CHAP authentication, with PA...; Question 277: Which two services can the ICMP Echo IP SLA provide? (Choose...; Question 278: How does an IP SLA ICMP Echo operation measure response time...; Question 279: Refer to the exhibit. Assume that all router interfaces are ...; Question 280: Refer to the exhibit. What statement is true of the configur...; Question 281: Which IPv6 address is the equivalent of the IPv4 interface l...; Question 282: What are three reasons to collect Netflow data on a company ...; Question 283: What are the benefit of using Netflow? (Choose three.)...; Question 284: Which statement is true, as relates to classful or classless...; Question 285: Select the action that results from executing these commands...; Question 286: Which component of an IPv6 OSPFv3 connection must be configu...; Question 287: Which two components are used to identify a neighbor in a BG...; Question 288: Which value is used to determine the active router in an HSR...; Question 289: What is the default encapsulation type for Cisco WAN serial ...; Question 290: Refer to the exhibit. What address is a feasible successor? ...; Question 291: Which two statements about the OSPF Router ID are true? (Cho...; Question 292: Which HSRP Feature was new in HSRPv2?...; Question 293: Which two steps must occur before two routers can become BGP...; Question 294: What are three characteristics of the OSPF routing protocol?...; Question 295: On which layer tcp/ip is ACL Apic-EM path?...; Question 296: Which two tasks use OSPFv3 hello packets? (Choose two.)...; Question 297: On which port type is the spanning-tree portfast command sup...; Question 298: Which statement about spanning-tree root-bridge election is ...; Question 299: To troubleshoot a network connection, you execute the ping u...; Question 300: Which address is the IPv6 all-RIP-routers multicast group ad...; Question 301: Which two characteristics of extended access lists are true?...; Question 302: From which PPPoE server configuration does a PPPoE client ge...; Question 303: Which protocol is incompatible with CGMP leave processing?...; Question 304: Which of the port is not part of STP protocol?...; Question 305: Refer to the exhibit. (Exhibit) While you troubleshoot a con...; Question 306: Which router command can be used to verify the type of cable...; Question 307: Which HSRP feature do you configure so that the device with ...; Question 308: In which LACP channel mode can the port initiate negotiation...; Question 309: Which three features are QoS congestion-management tools? (C...; Question 310: Which three statements about the ACEs that are matched by a ...; Question 311: Which three statements about inform-request options are true...; Question 312: A department decides to replace its hub with a Catalyst 2950...; Question 313: Which two statements describe characteristics of IPv6 unicas...; Question 314: Which command is used to display the collection of OSPF link...; Question 315: At which layer of the OSI model is RSTP used to prevent loop...; Question 316: Which three fields can be marked with QoS? (Choose three.)...; Question 317: Which four options are the HSRP states for a router? (Choose...; Question 318: Scenario Refer to the topology. Your company has decided to ...; Question 319: Which two EtherChannel PAgP modes can you configure? (Choose...; Question 320: Which routing protocol is most appropriate for sending and r...; Question 321: Which command do you enter so that a port enters the forward...; Question 322: For which reason can a GRE tunnel have an Up/DOWN status?...; Question 323: In which two models can control-plane functionality be imple...; Question 324: Which feature or value must be configured to enable EIGRPv6?...; Question 325: Refer to the exhibit. What commands must be configured on th...; Question 326: When a router undergoes the exchange protocol within OSPF, i...; Question 327: Syslog was configured with a level 3 trap. Which 3 types of ...; Question 328: Which two requirements must be met to allow two routers runn...; Question 329: Which purpose of the network command in OSPF configuration m...; Question 330: Unauthorized users have used Telnet to gain access to a comp...; Question 331: What can be done to secure the virtual terminal interfaces o...; Question 332: Which VLAN bridge priority value is assigned by the set span...; Question 333: Which utility can you use to identify redundant or shadow ru...; Question 334: Which command do use we to see SNMP version?...; Question 335: Which statement describes the process ID that is used to run...; Question 336: Instructions Enter Cisco IOS commands on device to verify ne...; Question 337: What two options are causes of network slowness that can res...; Question 338: Instructions This item contains several questions that you m...; Question 339: Which six-byte field in a basic Ethernet frame must be an in...; Question 340: What is a difference between TACACS+ and RADIUS in AAA?...; Question 341: How can you disable DTP on a switch port?...; Question 342: Refer to the exhibit. Given the output from the show ip eigr...; Question 343: Refer to the exhibit. From R1, a network administrator is ab...; Question 344: What is the Cisco recommended DSCP value for voice traffic?...; Question 345: Given an IP address 172.16.28.252 with a subnet mask of 255....; Question 346: Which purpose of the network command in the BGP configuratio...; Question 347: In order to comply with new auditing standards, a security a...; Question 348: Which command can you enter to determine whether a voice VLA...; Question 349: Which process is associated with spanning-tree convergence?...; Question 350: Which WAN topology provides a direct connection from each si...; Question 351: Which command do you enter to determine whether LACP is in u...; Question 352: In the Frame Relay network, which IP addresses would be assi...; Question 353: Which form of NAT maps multiple private IP addresses to a si...; Question 354: Refer to the exhibit. A network technician enters the follow...; Question 355: Where must you configure switch-level global features on a s...; Question 356: Which functionality does an SVI provide?...; Question 357: Which name describes an IPv6 host-enabled tunneling techniqu...; Question 358: Refer to the exhibit. If RTR01 is configured as shown, which...; Question 359: Which command allows you to verify the encapsulation type (C...; Question 360: Which feature can you use to restrict SNMP queries to a spec...; Question 361: The following configuration is applied to a Layer 2 Switch: ...; Question 362: Scenario Refer to the topology. Your company has connected t...; Question 363: Which encryption method does CHAP authentication use for the...; Question 364: After you configure a new router to connect to a host throug...; Question 365: Which two are features of IPv6? (Choose two.)...; Question 366: Which RPVST+ port state is excluded from all STP operations?...; Question 367: Which three are the components of SNMP? (Choose three.)...; Question 368: Which version of SNMP first allowed user-based access?...; Question 369: A network engineer wants to allow a temporary entry for a re...; Question 370: Refer to the exhibit. Which problem is indicated by this err...; Question 371: Which part of the PPPoE server configuration contains the in...; Question 372: Which port state is introduced by Rapid-PVST?...; Question 373: Instructions This item contains several questions that you m...; Question 374: Scenario Refer to the topology. Your company has connected t...; Question 375: In GLBP, which router will respond to client ARP requests?...; Question 376: Which statement about the default VLAN is true?...; Question 377: Which two benefits of using MPLS for WAN access are true? (C...; Question 378: Which WAN technology is secure and encrypted by default?...; Question 379: Which two statements are characteristics of a distance vecto...; Question 380: What are two drawbacks of implementing a link-state routing ...; Question 381: Which IPv6 address is valid?; Question 382: A network administrator has configured access list 173 to pr...; Question 383: Which two traffic types must always be transmitted on VLAN 1...

Question 36/383

LEAVE A REPLY

Download PDF File