200-105 Exam Dumps | Refer to the exhibit. A network associate has configured OSPF with the command: City(config-router)#

<< Prev Question Next Question >>

Question 12/383

Refer to the exhibit.
A network associate has configured OSPF with the command:
City(config-router)# network 192.168.12.64 0.0.0.63 area 0
After completing the configuration, the associate discovers that not all the interfaces are participating in OSPF. Which three of the interfaces shown in the exhibit will participate in OSPF according to this configuration statement? (Choose three.)

A. FastEthernet0 /0

B. FastEthernet0 /1

C. Serial0/0

D. Serial0/1.102

E. Serial0/1.103

F. Serial0/1.104

Question List (383q): Question 1: Which feature can you implement to reserve bandwidth for voi...; Question 2: Which BGP command do you enter to allow a device to exchange...; Question 3: Which command can you enter in a network switch configuratio...; Question 4: Which two pieces of information are provided by the show con...; Question 5: Which statement about using the keepalive command on a tunne...; Question 6: What is the default administrative distance of OSPF?...; Question 7: What is the minimum command to turn on encryption on SNMP?...; Question 8: Refer to the exhibit. Router4 can ping Router5 (172.16.6.5),...; Question 9: Which two actions must you take to configure a static EtherC...; Question 10: Which option is the benefit of implementing an intelligent D...; Question 11: Which two statements about LACP are true? (Choose two.)...; Question 12: Refer to the exhibit. A network associate has configured OSP...; Question 13: A network administrator enters the following command on a ro...; Question 14: Which command do you enter to determine the root priority?...; Question 15: What information does a router running a link-state protocol...; Question 16: Which statement describes VRRP object tracking?...; Question 17: Which two of these statements are true of IPv6 address repre...; Question 18: Which two features are compatible with SPAN sessions? (Choos...; Question 19: Refer to the exhibit. What is the most appropriate summariza...; Question 20: Which protocol authenticates connected devices before allowi...; Question 21: Which interface counter can you use to diagnose a duplex mis...; Question 22: Which command can you enter on a switch to determine the cur...; Question 23: Refer to the graphic. Users on the Holyoke router are unable...; Question 24: Which two statements about interior gateway routing protocol...; Question 25: How does using the service password-encryption command on a ...; Question 26: An administrator is troubleshooting a problem between router...; Question 27: Which statement about GRE tunnels is true?...; Question 28: Refer to the exhibit. Host A has tested connectivity to a re...; Question 29: Which two statements describe the process identifier that is...; Question 30: Which configuration can you apply to enable encapsulation on...; Question 31: Scenario Refer to the topology. Your company has decided to ...; Question 32: Which result occurs when you configure the switchport mode d...; Question 33: Which mode is compatible with Trunk, Access, and desirable p...; Question 34: Which value can you modify to configure a specific interface...; Question 35: Which command must you enter to prepare an interface to carr...; Question 36: What command is used to verify the DLCI destination address ...; Question 37: Which technology can prevent client devices from arbitrarily...; Question 38: Which QoS feature can change the value of the IPv4 Type of S...; Question 39: Which purpose of the network command in the BGP configuratio...; Question 40: Which statement about slow inter-VLAN forwarding is true?...; Question 41: Scenario Refer to the topology. Your company has decided to ...; Question 42: Refer to the exhibit. A technician pastes the configurations...; Question 43: If primary and secondary root switches with priority 16384 b...; Question 44: Refer to the exhibit. How should Switch1 and Switch2 be conn...; Question 45: Refer to the exhibit. Assuming that the entire network topol...; Question 46: Which command helps a network administrator to manage memory...; Question 47: Which two options are valid WAN connectivity methods? (Choos...; Question 48: Refer to the exhibit. Which statement describes DLCI 17? (Ex...; Question 49: Which command can you enter to assign an interface to the de...; Question 50: Which three options are the HSRP states for a router? (Choos...; Question 51: Which two privileged mode Cisco IOS commands can be used to ...; Question 52: Refer to the exhibit. Hosts in network 192.168.2.0 are unabl...; Question 53: Which option is the industry-standard protocol for Etherchan...; Question 54: Which three options are types of Layer 2 network attack? (Ch...; Question 55: Which two switch states are valid for 802.1w? (Choose two.)...; Question 56: Which three components must you configure to establish a GRE...; Question 57: Which command should you enter to allow carrying voice?...; Question 58: It has become necessary to configure an existing serial inte...; Question 59: When are packets processed by an inbound access list?...; Question 60: Which command do you enter to protect a PortFast-enabled por...; Question 61: Which two types of cloud services may require you to alter t...; Question 62: The ROUTE company has a small network. The network consists ...; Question 63: Which command do you enter to verify that a VLAN has been re...; Question 64: When troubleshooting Ethernet connectivity issues how can yo...; Question 65: Which Layer 2 protocol encapsulation type supports synchrono...; Question 66: What Cisco IOS feature can be enabled to pinpoint an applica...; Question 67: A network administrator needs to allow only one Telnet conne...; Question 68: In a GLBP network, who is responsible for the arp request?...; Question 69: What is the default Syslog facility level?...; Question 70: When is the most appropriate time to escalate an issue that ...; Question 71: In which two ways can you isolate the location of a connecti...; Question 72: After you notice that the SNMP manager is failing to receive...; Question 73: Which Cisco IOS feature can you use to dynamically identify ...; Question 74: Which technology supports fast provisioning for cloud resour...; Question 75: Which command do you enter to enable local authentication fo...; Question 76: Which protocol provides a method of sharing VLAN configurati...; Question 77: To which two categories of routing protocols does BGP belong...; Question 78: Refer to the exhibit. Which switch provides the spanning-tre...; Question 79: Refer to the exhibit. At the end of an RSTP election process...; Question 80: Which three options are types of slow VLAN connectivity? (Ch...; Question 81: Which result occurs when you configure the standby preempt c...; Question 82: What are three factors a network administrator must consider...; Question 83: What do SNMPv1 and SNMPv2 have in common?...; Question 84: A router has been configured to provide the nine users on th...; Question 85: Refer to the exhibit. (Exhibit) Router edge-1 is unable to e...; Question 86: What is the minimum level of SNMP that provides encryption?...; Question 87: Identify the four valid IPv6 addresses. (Choose four.)...; Question 88: Refer to the exhibit. How should the FastEthernet0/1 ports o...; Question 89: What is true about Ethernet? (Choose two.)...; 2 commentQuestion 90: Instructions Enter Cisco IOS commands on device to verify ne...; 1 commentQuestion 91: While troubleshooting the failure of an OSPFv3 Ethernet conn...; Question 92: Which command can be used from a PC to verify the connectivi...; Question 93: Disadvantages of using proxy ARP?...; Question 94: What are three advantages of vlans? (Choose three.)...; Question 95: Which two characteristics of stacked switches are true? (Cho...; Question 96: Which statement about STP root bridges is true?...; Question 97: Scenario Refer to the topology. Your company has decided to ...; Question 98: What are two enhancements that OSPFv3 supports over OSPFv2? ...; Question 99: The network administrator of the Oregon router adds the foll...; Question 100: Which IEEE standard does PVST+ use to tunnel information?...; Question 101: Which two statements about traffic shaping are true? (Choose...; Question 102: Which command do you enter to allow a new VLAN across a trun...; Question 103: Refer to the exhibit. If the router Cisco returns the given ...; Question 104: How does a router handle an incoming packet whose destinatio...; 1 commentQuestion 105: Instructions: Enter IOS commands on the Dubai router to veri...; Question 106: Refer to the exhibit. Which of these correctly describes the...; Question 107: Which three statements about the features of SNMPv2 and SNMP...; Question 108: In an HSRP failover environment, which two tasks must you pe...; Question 109: Which three statements are benefits of using a shadow router...; Question 110: At which layer of the OSI model does PPP perform?...; 1 commentQuestion 111: Which configuration enables OSPF for network 192.168.1.0/24?...; Question 112: Which two of these statements regarding RSTP are correct? (C...; Question 113: Refer to the exhibit. HostA cannot ping HostB. Assuming rout...; Question 114: What is a valid HSRP virtual MAC address?...; Question 115: Which WAN topology is most appropriate for a centrally locat...; Question 116: Refer to the exhibit. If the router R1 returns the given out...; Question 117: Refer to the exhibit. Some 2950 series switches are connecte...; Question 118: Which protocol supports sharing the VLAN configuration betwe...; Question 119: You are working in a data center environment and are assigne...; Question 120: Which statement about access lists that are applied to an in...; Question 121: Which statement about OSPFv3 configuration is true?...; Question 122: Refer to the exhibit. On R1 which routing protocol is in use...; 1 commentQuestion 123: Under normal operations, Cisco recommends that you configure...; Question 124: Refer to the exhibit. A frame on VLAN 1 on switch S1 is sent...; Question 125: Which type of topology is required by DMVPN?...; Question 126: What is the first step you perform to configure an SNMPv3 us...; Question 127: Which encapsulation type is a Frame Relay encapsulation type...; Question 128: Refer to the exhibit. What is the meaning of the term dynami...; Question 129: Which switch port mode prevents DTP frames from being sent?...; Question 130: A router has learned three possible routes that could be use...; Question 131: Refer to the exhibit. All three PCs on the network are in di...; Question 132: Instructions This item contains several questions that you m...; Question 133: Refer to the output from the show running-config command in ...; Question 134: Which two statements about using the CHAP authentication mec...; Question 135: In the Software-Defined Networking model, where is the inter...; Question 136: What does the "Inside Global" address represent in the confi...; Question 137: Refer to the topology and partial router configurations show...; Question 138: Which type of IPv6 ACL is applied first in the order of prec...; Question 139: Which commands are required to properly configure a router t...; Question 140: What are three valid reasons to assign ports to VLANs on a s...; Question 141: Which three statements about VTP features are true? (Choose ...; Question 142: Which two functions of the APIC-EM Path Trace ACL Analysis t...; Question 143: Which two protocols can detect native vlan mismatch errors? ...; Question 144: Which function does traffic shaping perform?...; Question 145: Which two Cisco IOS commands, used in troubleshooting, can e...; Question 146: What 8-bit field exists in IP packet for QoS?...; Question 147: Which statement about VLAN configuration is true?...; Question 148: Which role is used by VLAN 1 by default?...; Question 149: Which port type is used in a stacked deployment?...; Question 150: What OSPF command, when configured, will include all interfa...; Question 151: Which QoS prioritization method is most appropriate for inte...; Question 152: Which statement about MPLS is true?...; Question 153: Which command do you enter to configure client authenticatio...; Question 154: Which option is the main function of congestion management?...; Question 155: Which three elements must be used when you configure a route...; Question 156: You attempt to execute the APIC-EM ACL path trace feature wi...; Question 157: Refer to the exhibit. What does STATUS=ACTIVE refer to in th...; Question 158: A router receives information about network 192.168.10.0/24 ...; Question 159: When you deploy multilink PPP on your network, where must yo...; Question 160: Which networking function occurs on the data plane?...; Question 161: Which effect of the monitor session 16 source interface giga...; Question 162: For which type of connection is broadband PPPoE most appropr...; Question 163: Which device classes are used over serial links? (Choose two...; Question 164: What can cause two OSPF neighbors to be stuck in the EXSTART...; Question 165: Which three features are added in SNMPv3 over SNMPv2? (Choos...; Question 166: If host Z needs to send data through router R1 to a storage ...; Question 167: Which two features are supported only in named access lists?...; Question 168: Which three checks must you perform when troubleshooting EIG...; Question 169: Refer to the exhibit. What can be concluded from the output ...; Question 170: Which protocol can be used between administrative domains?...; Question 171: By default, which two K values does EIGRP for IPv6 use to ca...; Question 172: Refer to the exhibit. A packet with a source IP address of 1...; Question 173: Refer to the graphic and routing table for router R1. Based ...; Question 174: Workstation A has been assigned an IP address of 192.0.2.24/...; Question 175: Which two statements about static NAT translations are true?...; Question 176: A network administrator needs to configure a serial link bet...; Question 177: Instructions: Enter IOS commands on the Dubai router to veri...; Question 178: Which tool or utility can report whether traffic matching sp...; Question 179: Which command do you enter to verify an SVI?...; Question 180: In which configuration can a PPPoE client operate normally?...; Question 181: What does it take for BGP to establish connection? (Choose t...; Question 182: Refer to the exhibit. Which statement is true? (Exhibit)...; 1 commentQuestion 183: Refer to the exhibit. Which command do you enter so that R1 ...; Question 184: Refer to the exhibit. Which two statements are true about th...; Question 185: Refer to the exhibit. The output that is shown is generated ...; Question 186: VLAN 3 is not yet configured on your switch. What happens if...; Question 187: Which state does a port with BPDU guard enabled enter when i...; Question 188: Which VLAN bridge priority value will make a switch as root ...; Question 189: Which three features are supported when you use TACACS+ for ...; Question 190: Which programming language do you use to script interactions...; Question 191: In which three circumstances may your organization require a...; Question 192: Which command do you enter to configure local authentication...; Question 193: Which two actions must you take to configure a PAgP Ethernet...; Question 194: While you were troubleshooting a connection issue, a ping fr...; Question 195: What does split horizon prevent?...; Question 196: Refer to the exhibit. After you apply the give configuration...; Question 197: Which utility do you use to view IP traffic that is switched...; Question 198: The output of the show frame-relay pvc command shows "PVC ST...; Question 199: Which command do you enter to enable an interface to support...; Question 200: What is the best way to verify that a host has a path to oth...; Question 201: Instructions Enter Cisco IOS commands on device to verify ne...; Question 202: Which protocol is a Cisco proprietary implementation of STP?...; Question 203: Which two statements identify differences between single-hom...; Question 204: Which three describe the reasons large OSPF networks use a h...; Question 205: Refer to the exhibit. A junior network engineer has prepared...; Question 206: What is one benefit of PVST+?; Question 207: When you configure a new switch interface, to which VLAN it ...; Question 208: Which option describes a difference between EIGRP for IPv4 a...; Question 209: What is the default VLAN on an access port?...; Question 210: Which interior routing protocol reduces the size of route ta...; Question 211: Which two statements about switch stacking are true? (Choose...; Question 212: Scenario Refer to the topology. Your company has connected t...; Question 213: Refer to the exhibit. Which route will be found in the routi...; Question 214: Which WAN topology has the highest degree of reliability?...; Question 215: In which solution is a router ACL used?...; Question 216: Refer to the exhibit. Which subnet mask will place all hosts...; Question 217: Refer to the exhibit. How many interfaces on R1 should be co...; Question 218: Which channel mode is available to static EhterChannels?...; Question 219: Which switch architecture is scalable, flexible, resilient, ...; Question 220: Which command enables IPv6 forwarding on a Cisco router?...; Question 221: Refer to the exhibit. What command sequence will enable PAT ...; Question 222: What occurs on a Frame Relay network when the CIR is exceede...; Question 223: Which pairing reflects a correct protocol-and-metric relatio...; Question 224: What is the default DTP mode on a switch port?...; Question 225: Which two protocols can support trunking? (Choose two.)...; Question 226: Refer to the exhibit. Which address range efficiently summar...; Question 227: Which three protocols does APIC-EM support with Path Trace? ...; Question 228: Which technology supports multiple dynamic secure connection...; Question 229: How can you manually configure a switch so that it is select...; Question 230: Host is able to ping a web server but it is not able to do H...; Question 231: When you enable PortFast on a switch port, the port immediat...; Question 232: Which statements are true about EIGRP successor routes? (Cho...; Question 233: Which two data link layers are supported by Cisco IOS Softwa...; Question 234: Which statement about switch access ports is true?...; Question 235: Refer to the exhibit. Which two statements about the configu...; Question 236: The command frame-relay map ip 10.121.16.8 102 broadcast was...; Question 237: Which two steps must you perform on each device that is conf...; Question 238: Which set of commands is recommended to prevent the use of a...; Question 239: Which three effects of using local SPAN are true? (Choose th...; Question 240: Refer to the exhibit. The network shown in the exhibit has j...; Question 241: Which Layer 2 attack is specifically mitigated by changing t...; Question 242: Refer to the exhibit. To what does the 128 refer in the rout...; Question 243: Which protocol can cause overload on a CPU of a managed devi...; Question 244: What type of attack is when trusted source replace mac table...; Question 245: Which information is provided by the output of the show snmp...; Question 246: Instructions This item contains several questions that you m...; Question 247: Which options are the two differences between HSRP versions ...; Question 248: Which term describes a spanning-tree network that has all sw...; Question 249: For which reason can OSPFv3 fail to start between two router...; Question 250: Which type does a port become when it receives the best BPDU...; Question 251: Refer to the exhibit. The network is converged. After link-s...; Question 252: The internetwork infrastructure of company XYZ consists of a...; Question 253: Which protocol provides a method of sharing VLAN configurati...; Question 254: Which combination of values is valid for a router-on-a-stick...; Question 255: What is the alert message generated by SNMP agents called? (...; Question 256: Which feature does PPP use to encapsulate multiple protocols...; Question 257: Which two statements about exterior gateway routing protocol...; Question 258: Refer to the exhibit. Host A pings interface S0/0 on router ...; Question 259: Which two statements about the spanning-tree bridge ID are t...; Question 260: Refer to the exhibit. Assume that all of the router interfac...; Question 261: Which feature would prevent a workstation from receiving a D...; Question 262: Which command do you enter to determine the status of the SV...; Question 263: Which two statements about VLAN port assignment are true? (C...; Question 264: Which command reveals the last method used to powercycle a r...; Question 265: Which configuration do you apply to an HSRP router so that i...; Question 266: What are OSPF's default hello and dead timers? (Choose two)...; Question 267: What are three reasons that an organization with multiple br...; Question 268: Refer to the exhibit. Based on the exhibited routing table, ...; Question 269: Which three statements about DTP are true? (Choose three.)...; Question 270: Refer to the exhibit. Why has this switch not been elected t...; Question 271: Which function is performed by a TACACS+ server?...; Question 272: Refer to the exhibit. Each of these four switches has been c...; Question 273: Which type of routing protocol uses the Bellman-Ford algorit...; Question 274: The network administrator is asked to configure 113 point-to...; Question 275: Which option describes a benefit of a point-to-point leased ...; Question 276: Which command is used to enable CHAP authentication, with PA...; Question 277: Which two services can the ICMP Echo IP SLA provide? (Choose...; Question 278: How does an IP SLA ICMP Echo operation measure response time...; Question 279: Refer to the exhibit. Assume that all router interfaces are ...; Question 280: Refer to the exhibit. What statement is true of the configur...; Question 281: Which IPv6 address is the equivalent of the IPv4 interface l...; Question 282: What are three reasons to collect Netflow data on a company ...; Question 283: What are the benefit of using Netflow? (Choose three.)...; Question 284: Which statement is true, as relates to classful or classless...; Question 285: Select the action that results from executing these commands...; Question 286: Which component of an IPv6 OSPFv3 connection must be configu...; Question 287: Which two components are used to identify a neighbor in a BG...; Question 288: Which value is used to determine the active router in an HSR...; Question 289: What is the default encapsulation type for Cisco WAN serial ...; Question 290: Refer to the exhibit. What address is a feasible successor? ...; Question 291: Which two statements about the OSPF Router ID are true? (Cho...; Question 292: Which HSRP Feature was new in HSRPv2?...; Question 293: Which two steps must occur before two routers can become BGP...; Question 294: What are three characteristics of the OSPF routing protocol?...; Question 295: On which layer tcp/ip is ACL Apic-EM path?...; Question 296: Which two tasks use OSPFv3 hello packets? (Choose two.)...; Question 297: On which port type is the spanning-tree portfast command sup...; Question 298: Which statement about spanning-tree root-bridge election is ...; Question 299: To troubleshoot a network connection, you execute the ping u...; Question 300: Which address is the IPv6 all-RIP-routers multicast group ad...; Question 301: Which two characteristics of extended access lists are true?...; Question 302: From which PPPoE server configuration does a PPPoE client ge...; Question 303: Which protocol is incompatible with CGMP leave processing?...; Question 304: Which of the port is not part of STP protocol?...; Question 305: Refer to the exhibit. (Exhibit) While you troubleshoot a con...; Question 306: Which router command can be used to verify the type of cable...; Question 307: Which HSRP feature do you configure so that the device with ...; Question 308: In which LACP channel mode can the port initiate negotiation...; Question 309: Which three features are QoS congestion-management tools? (C...; Question 310: Which three statements about the ACEs that are matched by a ...; Question 311: Which three statements about inform-request options are true...; Question 312: A department decides to replace its hub with a Catalyst 2950...; Question 313: Which two statements describe characteristics of IPv6 unicas...; Question 314: Which command is used to display the collection of OSPF link...; Question 315: At which layer of the OSI model is RSTP used to prevent loop...; Question 316: Which three fields can be marked with QoS? (Choose three.)...; Question 317: Which four options are the HSRP states for a router? (Choose...; Question 318: Scenario Refer to the topology. Your company has decided to ...; Question 319: Which two EtherChannel PAgP modes can you configure? (Choose...; Question 320: Which routing protocol is most appropriate for sending and r...; Question 321: Which command do you enter so that a port enters the forward...; Question 322: For which reason can a GRE tunnel have an Up/DOWN status?...; Question 323: In which two models can control-plane functionality be imple...; Question 324: Which feature or value must be configured to enable EIGRPv6?...; Question 325: Refer to the exhibit. What commands must be configured on th...; Question 326: When a router undergoes the exchange protocol within OSPF, i...; Question 327: Syslog was configured with a level 3 trap. Which 3 types of ...; Question 328: Which two requirements must be met to allow two routers runn...; Question 329: Which purpose of the network command in OSPF configuration m...; Question 330: Unauthorized users have used Telnet to gain access to a comp...; Question 331: What can be done to secure the virtual terminal interfaces o...; Question 332: Which VLAN bridge priority value is assigned by the set span...; Question 333: Which utility can you use to identify redundant or shadow ru...; Question 334: Which command do use we to see SNMP version?...; Question 335: Which statement describes the process ID that is used to run...; Question 336: Instructions Enter Cisco IOS commands on device to verify ne...; Question 337: What two options are causes of network slowness that can res...; Question 338: Instructions This item contains several questions that you m...; Question 339: Which six-byte field in a basic Ethernet frame must be an in...; Question 340: What is a difference between TACACS+ and RADIUS in AAA?...; Question 341: How can you disable DTP on a switch port?...; Question 342: Refer to the exhibit. Given the output from the show ip eigr...; Question 343: Refer to the exhibit. From R1, a network administrator is ab...; Question 344: What is the Cisco recommended DSCP value for voice traffic?...; Question 345: Given an IP address 172.16.28.252 with a subnet mask of 255....; Question 346: Which purpose of the network command in the BGP configuratio...; Question 347: In order to comply with new auditing standards, a security a...; Question 348: Which command can you enter to determine whether a voice VLA...; Question 349: Which process is associated with spanning-tree convergence?...; Question 350: Which WAN topology provides a direct connection from each si...; Question 351: Which command do you enter to determine whether LACP is in u...; Question 352: In the Frame Relay network, which IP addresses would be assi...; Question 353: Which form of NAT maps multiple private IP addresses to a si...; Question 354: Refer to the exhibit. A network technician enters the follow...; Question 355: Where must you configure switch-level global features on a s...; Question 356: Which functionality does an SVI provide?...; Question 357: Which name describes an IPv6 host-enabled tunneling techniqu...; Question 358: Refer to the exhibit. If RTR01 is configured as shown, which...; Question 359: Which command allows you to verify the encapsulation type (C...; Question 360: Which feature can you use to restrict SNMP queries to a spec...; Question 361: The following configuration is applied to a Layer 2 Switch: ...; Question 362: Scenario Refer to the topology. Your company has connected t...; Question 363: Which encryption method does CHAP authentication use for the...; Question 364: After you configure a new router to connect to a host throug...; Question 365: Which two are features of IPv6? (Choose two.)...; Question 366: Which RPVST+ port state is excluded from all STP operations?...; Question 367: Which three are the components of SNMP? (Choose three.)...; Question 368: Which version of SNMP first allowed user-based access?...; Question 369: A network engineer wants to allow a temporary entry for a re...; Question 370: Refer to the exhibit. Which problem is indicated by this err...; Question 371: Which part of the PPPoE server configuration contains the in...; Question 372: Which port state is introduced by Rapid-PVST?...; Question 373: Instructions This item contains several questions that you m...; Question 374: Scenario Refer to the topology. Your company has connected t...; Question 375: In GLBP, which router will respond to client ARP requests?...; Question 376: Which statement about the default VLAN is true?...; Question 377: Which two benefits of using MPLS for WAN access are true? (C...; Question 378: Which WAN technology is secure and encrypted by default?...; Question 379: Which two statements are characteristics of a distance vecto...; Question 380: What are two drawbacks of implementing a link-state routing ...; Question 381: Which IPv6 address is valid?; Question 382: A network administrator has configured access list 173 to pr...; Question 383: Which two traffic types must always be transmitted on VLAN 1...

Question 12/383

LEAVE A REPLY

Download PDF File