- Home
- CheckPoint
- Check Point Certified Security Master - R80
- CheckPoint.156-115.80.v2018-11-27.q59
- Question 21
Valid 156-115.80 Dumps shared by ExamDiscuss.com for Helping Passing 156-115.80 Exam! ExamDiscuss.com now offer the newest 156-115.80 exam dumps, the ExamDiscuss.com 156-115.80 exam questions have been updated and answers have been corrected get the newest ExamDiscuss.com 156-115.80 dumps with Test Engine here:
Access 156-115.80 Dumps Premium Version
(160 Q&As Dumps, 35%OFF Special Discount Code: freecram)
<< Prev Question Next Question >>
Question 21/59
Which of the connections cannot be accelerated with SecureXL?
Correct Answer: B
- Question List (59q)
- Question 1: Where does the translation occur with Hide NAT?...
- Question 2: The maximum number of critical devices or pnotes on a cluste...
- Question 3: The Security Gateway is installed on GAiA R80. The default p...
- 2 commentQuestion 4: A Firewall administrator is attempting to push a policy to a...
- Question 5: The pepd and pdpd daemons are used by which Software blade?...
- 1 commentQuestion 6: Which Check Point daemon, if it stops responding or goes dow...
- 1 commentQuestion 7: URL Filtering is an essential part of Web Security in the Ga...
- Question 8: Which command should be used to insert fw monitor before sec...
- Question 9: Which kernel table stores information about NAT connections?...
- Question 10: Of how many packets consists Main Mode in Phase 1?...
- Question 11: Which one of following commands should you run to display HT...
- Question 12: What does the command "vpn shell tunnels delete all ike" do?...
- Question 13: What is the name of the table that an administrator would re...
- Question 14: While using IPS, the network performance is being impacted o...
- Question 15: Which "fwm" command syntax will instruct the gateway to load...
- Question 16: How can you print the session UUID and the UUID of a connect...
- Question 17: When enabling hyper-threading on a Security Gateway, the adm...
- Question 18: What occurs when Bypass Under Load activated?...
- Question 19: Which command is used to enable IPv6 on Security Gateway?...
- Question 20: How can you ensure that a particular service does not use th...
- 1 commentQuestion 21: Which of the connections cannot be accelerated with SecureXL...
- 1 commentQuestion 22: Having a look at the output of the "fwaccel conns" command, ...
- Question 23: Fill in the blank. The tool ____________________ generates a...
- Question 24: You run "cat/proc/smt_status" on your security gateway and t...
- Question 25: Which is the correct "fw monitor" syntax for creating a capt...
- Question 26: Which one of the following does not belong to an initial sta...
- Question 27: What is the command to check the current status of hyper-thr...
- Question 28: What is the default setting and minimum value of the Sync ti...
- Question 29: Fill in the blank: The R80 feature _________________ permits...
- Question 30: In R80 spoofing is defined as a method of:...
- Question 31: What is enabled by the command "vpn debug mon"?...
- Question 32: How many layers are incorporated in IPS detection and what a...
- Question 33: What does CMI stand for in relation to the Access Control Po...
- Question 34: Fill in the blank: The R80 utility fw monitoris used to trou...
- Question 35: Which of the following is correct in a Threat Prevention pol...
- Question 36: Which Check Point utility should be used to assist in analyz...
- Question 37: Which type of SecureXL templates is enabled by default on Se...
- Question 38: What is the difference between disabling SecureXL by running...
- Question 39: Where will the command, "fw monitor -pi -vpn", be inserted i...
- Question 40: Which of the following statements is TRUE about R80 manageme...
- Question 41: You issued the command "set ipv6-state on" in order to enabl...
- Question 42: If cluster members are geographically separated and the time...
- Question 43: After determining that the IPS Blade is causing high resourc...
- Question 44: What process(es) should be checked if there is high I/O and ...
- Question 45: Which kernel debug flag should you use to troubleshoot NAT c...
- Question 46: You are working with multiple Security Gateways enforcing an...
- Question 47: Your customer is experiencing problems connecting to the Sec...
- Question 48: What is the difference between Client-Side and Server-Side N...
- 1 commentQuestion 49: For organizations with existing IPv4 networks who wish to mo...
- Question 50: Which of the following inputs is suitable for debugging HTTP...
- 1 commentQuestion 51: Joey's implementing a new R80.10 firewall cluster into the n...
- Question 52: Which daemon would you debug if you have issues acquiring id...
- Question 53: What effect would change the parameter of fwha_timer_cpha_re...
- Question 54: What is the correct command to turn off an IKE debug?...
- Question 55: If certain services should not use the Cluster Object IP Add...
- 1 commentQuestion 56: Which file would you need to make sure you collect when debu...
- Question 57: Which of the following ports are used for SIC?...
- Question 58: Which templates for SecureXL are not enabled by default?...
- Question 59: Which of the following is NOT a special consideration while ...
[×]
Download PDF File
Enter your email address to download CheckPoint.156-115.80.v2018-11-27.q59.pdf
Recent Comments (The most recent comments are at the top.)
Incorrect answer. As per sk32578 C is correct