- Home
- CheckPoint
- Check Point Certified Security Master - R80
- CheckPoint.156-115.80.v2018-11-27.q59
- Question 6
Valid 156-115.80 Dumps shared by ExamDiscuss.com for Helping Passing 156-115.80 Exam! ExamDiscuss.com now offer the newest 156-115.80 exam dumps, the ExamDiscuss.com 156-115.80 exam questions have been updated and answers have been corrected get the newest ExamDiscuss.com 156-115.80 dumps with Test Engine here:
Access 156-115.80 Dumps Premium Version
(160 Q&As Dumps, 35%OFF Special Discount Code: freecram)
<< Prev Question Next Question >>
Question 6/59
Which Check Point daemon, if it stops responding or goes down, results in connections from the SmartConsole to the Management Server failing?
Correct Answer: A
- Question List (59q)
- Question 1: Where does the translation occur with Hide NAT?...
- Question 2: The maximum number of critical devices or pnotes on a cluste...
- Question 3: The Security Gateway is installed on GAiA R80. The default p...
- 2 commentQuestion 4: A Firewall administrator is attempting to push a policy to a...
- Question 5: The pepd and pdpd daemons are used by which Software blade?...
- 1 commentQuestion 6: Which Check Point daemon, if it stops responding or goes dow...
- 1 commentQuestion 7: URL Filtering is an essential part of Web Security in the Ga...
- Question 8: Which command should be used to insert fw monitor before sec...
- Question 9: Which kernel table stores information about NAT connections?...
- Question 10: Of how many packets consists Main Mode in Phase 1?...
- Question 11: Which one of following commands should you run to display HT...
- Question 12: What does the command "vpn shell tunnels delete all ike" do?...
- Question 13: What is the name of the table that an administrator would re...
- Question 14: While using IPS, the network performance is being impacted o...
- Question 15: Which "fwm" command syntax will instruct the gateway to load...
- Question 16: How can you print the session UUID and the UUID of a connect...
- Question 17: When enabling hyper-threading on a Security Gateway, the adm...
- Question 18: What occurs when Bypass Under Load activated?...
- Question 19: Which command is used to enable IPv6 on Security Gateway?...
- Question 20: How can you ensure that a particular service does not use th...
- 1 commentQuestion 21: Which of the connections cannot be accelerated with SecureXL...
- 1 commentQuestion 22: Having a look at the output of the "fwaccel conns" command, ...
- Question 23: Fill in the blank. The tool ____________________ generates a...
- Question 24: You run "cat/proc/smt_status" on your security gateway and t...
- Question 25: Which is the correct "fw monitor" syntax for creating a capt...
- Question 26: Which one of the following does not belong to an initial sta...
- Question 27: What is the command to check the current status of hyper-thr...
- Question 28: What is the default setting and minimum value of the Sync ti...
- Question 29: Fill in the blank: The R80 feature _________________ permits...
- Question 30: In R80 spoofing is defined as a method of:...
- Question 31: What is enabled by the command "vpn debug mon"?...
- Question 32: How many layers are incorporated in IPS detection and what a...
- Question 33: What does CMI stand for in relation to the Access Control Po...
- Question 34: Fill in the blank: The R80 utility fw monitoris used to trou...
- Question 35: Which of the following is correct in a Threat Prevention pol...
- Question 36: Which Check Point utility should be used to assist in analyz...
- Question 37: Which type of SecureXL templates is enabled by default on Se...
- Question 38: What is the difference between disabling SecureXL by running...
- Question 39: Where will the command, "fw monitor -pi -vpn", be inserted i...
- Question 40: Which of the following statements is TRUE about R80 manageme...
- Question 41: You issued the command "set ipv6-state on" in order to enabl...
- Question 42: If cluster members are geographically separated and the time...
- Question 43: After determining that the IPS Blade is causing high resourc...
- Question 44: What process(es) should be checked if there is high I/O and ...
- Question 45: Which kernel debug flag should you use to troubleshoot NAT c...
- Question 46: You are working with multiple Security Gateways enforcing an...
- Question 47: Your customer is experiencing problems connecting to the Sec...
- Question 48: What is the difference between Client-Side and Server-Side N...
- 1 commentQuestion 49: For organizations with existing IPv4 networks who wish to mo...
- Question 50: Which of the following inputs is suitable for debugging HTTP...
- 1 commentQuestion 51: Joey's implementing a new R80.10 firewall cluster into the n...
- Question 52: Which daemon would you debug if you have issues acquiring id...
- Question 53: What effect would change the parameter of fwha_timer_cpha_re...
- Question 54: What is the correct command to turn off an IKE debug?...
- Question 55: If certain services should not use the Cluster Object IP Add...
- 1 commentQuestion 56: Which file would you need to make sure you collect when debu...
- Question 57: Which of the following ports are used for SIC?...
- Question 58: Which templates for SecureXL are not enabled by default?...
- Question 59: Which of the following is NOT a special consideration while ...
[×]
Download PDF File
Enter your email address to download CheckPoint.156-115.80.v2018-11-27.q59.pdf
Recent Comments (The most recent comments are at the top.)
None of the options are correct. As per sk97638, process fwm handles Communication between SmartConsole applications and Security Management Server.