<< Prev Question Next Question >>

Question 17/44

Click the Exhibit.

Your network is experiencing congestion across the link between R2 and R3. You must make changes to alleviate traffic congestion from R3 to R2.
Referring to the exhibit, which two commands would accomplish this task? (Choose two.) A:

B:

C:

D:

LEAVE A REPLY

Your email address will not be published. Required fields are marked *

Question List (44q)
Question 1: Click the Exhibit. (Exhibit) You have deployed the access co...
Question 2: Which protocol is used for port-level access control and aut...
Question 3: Which three statements are true about strict-high priority q...
Question 4: Click the Exhibit. (Exhibit) You have deployed Sparse Mode m...
Question 5: In a Layer 2 environment where 802.1X is deployed with its d...
Question 6: Click the Exhibit. (Exhibit) You are troubleshooting an OSPF...
Question 7: Click the Exhibit. (Exhibit) You are adding a Junos Fusion s...
Question 8: Click the Exhibit. (Exhibit) You have three switches, each w...
Question 9: Click the Exhibit. (Exhibit) The Receiver is attempting to j...
Question 10: Click the Exhibit. (Exhibit) Router1, in peer AS 65001, adve...
Question 11: Click the Exhibit. (Exhibit) Referring to the exhibit, traff...
Question 12: Which statement is correct about CoS policers on Junos devic...
Question 13: A new PoE+VoIP handset was added to an EX Series device. The...
Question 14: Which statement is correct about MSTP?...
Question 15: Click the Exhibit. (Exhibit) You have a workstation and VoIP...
Question 16: Click the Exhibit. (Exhibit) A customer is concerned that th...
Question 17: Click the Exhibit. (Exhibit) Your network is experiencing co...
Question 18: Click the Exhibit. (Exhibit) Referring to the exhibit, you a...
Question 19: Which protocol is a multicast routing protocol?...
Question 20: When configuring class of service, what would you use to all...
Question 21: Click the Exhibit. (Exhibit) Referring to the exhibit, which...
Question 22: Click the Exhibit. (Exhibit) You are configuring dynamic ren...
Question 23: Click the Exhibit. (Exhibit) Router R1, in peer AS 65001, ad...
Question 24: You want to implement an RP in your PIM sparse mode environm...
Question 25: Click the Exhibit. (Exhibit) You have just configured on an ...
Question 26: Click the Exhibit. (Exhibit) Referring to the exhibit, you h...
Question 27: You configured static mode power management on an EX4300 to ...
Question 28: Click the Exhibit. (Exhibit) Which AS path matches the AS pa...
Question 29: Click the Exhibit. (Exhibit) Referring to the exhibit, Area ...
Question 30: You are configuring a scheduler map on an EX9200 Series devi...
Question 31: Click the Exhibit. (Exhibit) Referring to the exhibit which ...
Question 32: Which two statements are true about 802.1Z dynamic filters b...
Question 33: Click the Exhibit. (Exhibit) Switch 4 is rebooted as shown i...
Question 34: OSFP is stuck in the ExStart state. What is a common cause o...
Question 35: Which two statements are true about OSPFv3? (Choose two.)...
Question 36: You are enabling 802.1X authentication on an EX Series devic...
Question 37: You created a firewall rule to protect the Routing Engine. A...
Question 38: Click the exhibit. (Exhibit) Where is the policy shown in th...
Question 39: What information must you gather from the satellite device t...
Question 40: Computers on the network are assigned IP addresses from DHCP...
Question 41: Click the Exhibit. (Exhibit) The ping command shows that con...
Question 42: You are asked to merge a RIP network with your OSPF network....
Question 43: Click the Exhibit. (Exhibit) You have configured 802.1X sing...
Question 44: Click the Exhibit. (Exhibit) All of the clients attached to ...