JN0-643 Exam Dumps | -- Exhibit -- {master:0}[edit] user@router# run show ospf interface vl-10.20.10.2 extensive Interface

<< Prev Question Next Question >>

Question 160/209

-- Exhibit --
{master:0}[edit]
user@router# run show ospf interface vl-10.20.10.2 extensive
Interface State Area DR ID BDR ID Nbrs
vl-10.20.10.2 Down 0.0.0.0 0.0.0.0 0.0.0.0 0
TypE. Virtual, Address: 0.0.0.0, Mask: 0.0.0.0, MTU: 0, Cost: 1
Transit AreA. 0.0.0.1
Adj count: 0
Hello: 10, DeaD. 40, ReXmit: 5, Not Stub
Auth typE. None
Protection typE. None, No eligible backup
Topology default (ID 0) -> Down, Cost: 0
-- Exhibit --
Click the Exhibit button.
Your company is integrating another OSPF area into your existing OSPF infrastructure. You created a virtual link that spans Area 2 and connects Area 3 to the backbone area.
Based on the exhibit, what is preventing the adjacency?

A. The wrong transit area is configured.

B. No designated router (DR) has been elected.

C. The interface configured for the virtual link is incorrect. It should be a vt and not a vl interface.

D. The backup route to Area 2 has not been configured.

Question List (209q): Question 1: -- Exhibit -- [edit] user@switch# commit error: Trunk interf...; Question 2: You are configuring port ge-0/0/0 on an EX Series switch con...; Question 3: Which connection method do OSPF routers use to communicate w...; Question 4: -- Exhibit -- user@router> show configuration routing-opt...; Question 5: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 6: Which two statements are correct about L2PT? (Choose two.)...; Question 7: On SRX Series devices, in which order does CoS process ingre...; Question 8: Which option is a valid IPv6 multicast address?...; Question 9: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 10: Which AS path regular expression matches only routes origina...; Question 11: What is the significance of the multicast address range 224....; Question 12: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 13: -- Exhibit -- user@switch-1> show spanning-tree bridge ST...; Question 14: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 15: Your company asks you to configure multicast routing on a Ju...; Question 16: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 17: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 18: Which two statements are true about the configuration shown ...; Question 19: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 20: A security camera is connected to an EX Series switch. You a...; Question 21: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 22: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 23: You want to control bursts of HTTP traffic entering your SRX...; Question 24: -- Exhibit -- user@switch> show spanning-tree bridge STP ...; Question 25: -- Exhibit -- [edit] user@router# run show ospf database ext...; Question 26: -- Exhibit -- user@router> show class-of-service schedule...; Question 27: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 28: -- Exhibit -- user@router# run show route receive-protocol b...; Question 29: In your 802.1X-enabled network, a RADIUS server fails to res...; Question 30: A coffee shop offering free Internet service to customers wa...; Question 31: -- Exhibit -- user@router> show bgp summary Groups: 3 Pee...; Question 32: You have been asked to implement 802.1X in your network and ...; Question 33: Voice traffic is coming in on UDP port 17689. This traffic m...; Question 34: Which statement is true about using an OSPF import policy?...; Question 35: You have been asked to implement a private VLAN with two com...; Question 36: You are a service provider and have multiple customers in a ...; Question 37: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 38: -- Exhibit -- (Exhibit) -- Exhibit -- Click the Exhibit butt...; Question 39: -- Exhibit -- user@RP> show pim join extensive InstancE. ...; Question 40: You are asked to create a BGP routing policy that will delet...; Question 41: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 42: Which statement regarding LLDP update messages is correct?...; Question 43: What are two benefits of configuring OSPF database protectio...; Question 44: When 802.1X, MAC-RADIUS, and Captive Portal are enabled on a...; Question 45: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 46: R1 has an OSPF adjacency with R2 over a point-to-point link....; Question 47: Which statement is true regarding the SPF algorithm?...; Question 48: What is an IP multicast routing protocol?...; Question 49: -- Exhibit -- user@switch# run show spanning-tree statistics...; Question 50: -- Exhibit -- [edit protocols ospf] user@R2# show area 0.0.0...; Question 51: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 52: -- Exhibit -- {master:0} user@switch> show dot1x interfac...; Question 53: When using PIM-SM in SSM mode, which event triggers the crea...; Question 54: Two PCs are attached to a hub, which is attached to port ge-...; Question 55: Which statement is true about MVRP?...; Question 56: -- Exhibit -- user@SwitchA# show protocols dot1x authenticat...; Question 57: -- Exhibit -- user@router> show configuration routing-opt...; Question 58: You are asked to implement MSTP on all devices in your Layer...; Question 59: Which two statements about the voice VLAN feature are correc...; Question 60: Which configuration parameter causes a router to ignore rout...; Question 61: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 62: -- Exhibit -- Controller Maximum Power Guard Management Stat...; Question 63: In MSTP, which two factors determine the root bridge in each...; Question 64: -- Exhibit -- user@router>show route advertising-protocol...; Question 65: Which two statements are true about MSDP mesh groups? (Choos...; Question 66: During the BGP route-resolution process, the Junos OS must c...; 1 commentQuestion 67: R1 and R2 are ASBRs in the same area, each with an equal cos...; Question 68: Which set of BGP attributes is preferred by the Junos OS?...; Question 69: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 70: Which two LSA types are only generated by an ABR router? (Ch...; Question 71: A user complains about connectivity problems from their IP a...; Question 72: -- Exhibit -- {master:0}[edit] user@router# show class-of-se...; Question 73: Area 1 is configured as an NSSA with no summaries. Which thr...; Question 74: -- Exhibit -- user@router> show bgp summary Groups: 1 Pee...; Question 75: You are troubleshooting an LLDP neighbor and cannot see the ...; Question 76: Which CoS component helps with TCP global synchronization pr...; Question 77: -- Exhibit -- Mar 16 17:54:51.930726 OSPF periodic xmit from...; Question 78: -- Exhibit -- user@router> show log ospf Sep 19 00:22:13....; Question 79: How does an administrator block IGMP reports for the 239.0.0...; Question 80: You are implementing MSTP in your network. Which three value...; Question 81: -- Exhibit -- {master:0}[edit] user@switch# show vlans v200 ...; Question 82: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 83: An emergency Class 3 IP phone is connected to an EX Series s...; Question 84: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 85: You are asked to set up 802.1X port authentication for all a...; Question 86: -- Exhibit -- [edit policy-options] user@router# show policy...; Question 87: -- Exhibit -- {master:0}[edit] user@switch# show vlans v1 { ...; Question 88: You notice that an interface receiving traffic from multiple...; Question 89: A non-802.1X printer is connected to ge-0/0/0 on an EX Serie...; Question 90: You are asked to implement a filter-based VLAN assignment. Y...; Question 91: -- Exhibit -- user@router> show ospf route Topology defau...; Question 92: A medium-sized enterprise has some devices that are 802.1X c...; Question 93: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 94: You are implementing PoE on your EX Series switch to provide...; Question 95: -- Exhibit -- user@R1> show configuration protocols pim r...; Question 96: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 97: You have implemented 802.1X authentication in your Layer 2 n...; Question 98: A company is deploying a new 802.1X port-based security infr...; Question 99: -- Exhibit -- user@SwitchA# show protocols mstp configuratio...; Question 100: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 101: Which protocol reachability is advertised by OSPFv2?...; Question 102: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 103: You must troubleshoot a CoS issue on an Ethernet interface w...; Question 104: An OSPF router is an ABR but not an ASBR. Which three types ...; Question 105: You must prioritize VoIP packets on your network. Which feat...; Question 106: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 107: You just configured an interface as an access port and it is...; Question 108: A Layer 2 forwarding loop occurred on your network during a ...; Question 109: When using PIM-SM in ASM mode, which two events trigger the ...; Question 110: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 111: -- Exhibit -- [edit protocols] user@switch# commit [edit pro...; Question 112: On your EX Series switch you must configure a delay buffer f...; Question 113: You are asked to configure graceful restart in your network....; Question 114: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 115: You are configuring CoS classifiers and want to use both BA ...; Question 116: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 117: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 118: -- Exhibit -- [edit protocols ospf] user@area-1-abr# show ar...; Question 119: Which CoS feature avoids congestion in a device by limiting ...; Question 120: Which two statements are correct about MSTP? (Choose two.)...; Question 121: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 122: You are asked to reconfigure a CoS scheduler to limit the as...; Question 123: You want to provide reachability to your data center by adve...; Question 124: Which statement is true about LLDP?...; Question 125: You are asked to configure a CoS weighted tail drop profile ...; Question 126: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 127: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 128: You are configuring PIM-SM for your network, and want to use...; Question 129: -- Exhibit -- user@SwitchA# show protocols mstp configuratio...; Question 130: -- Exhibit -- MSTP information Context identifier : 0 Region...; Question 131: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 132: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 133: A network administrator is configuring CoS on a switch and a...; Question 134: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 135: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 136: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 137: What are three types of PVLAN broadcast domains? (Choose thr...; Question 138: -- Exhibit -- {master:0}[edit protocols dot1x] user@switch# ...; Question 139: Which two statements are true about SSM implementations on J...; Question 140: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 141: Which two statements about MVRP on EX Series switches are tr...; Question 142: A network administrator is configuring CoS on a switch and a...; Question 143: -- Exhibit -- Mar 16 18:39:15.800390 BGP RECV 172.14.10.2+57...; Question 144: You are asked to configure an interface policer. You must en...; Question 145: If your WAN-edge router is multihomed to different ISPs, whi...; Question 146: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 147: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 148: You are asked to implement a captive portal on your EX Serie...; Question 149: You are asked to implement VSTP on all devices in your Layer...; Question 150: -- Exhibit -- [edit] user@R1# show routing-options router-id...; Question 151: You are configuring BGP peering with a neighboring AS. Multi...; Question 152: -- Exhibit -- {master:0}[edit] user@switch# show ethernet-sw...; Question 153: -- Exhibit -- user@R1> show pim join extensive InstancE. ...; Question 154: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 155: You have been asked to implement a private VLAN with two com...; Question 156: You are setting up a new switch in your network that is usin...; Question 157: Your company recently implemented Layer 2 authentication and...; Question 158: -- Exhibit -- OSPF database, Area 0.0.0.0 Type ID Adv Rtr Se...; Question 159: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 160: -- Exhibit -- {master:0}[edit] user@router# run show ospf in...; Question 161: You are troubleshooting a problem on interface ge-0/0/3. Whi...; Question 162: -- Exhibit -- Mar 16 17:48:06.145257 OSPF periodic xmit from...; Question 163: Which multicast group is used for all PIM routers?...; Question 164: What is a valid router ID configuration for OSPFv3 in the Ju...; Question 165: -- Exhibit -- 20.0.0.0/8 *[BGP/170] 01:10:38, localpref 100,...; Question 166: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 167: You have a requirement for a device to provide 20 W of power...; Question 168: Your company makes extensive use of VSTP in your network for...; Question 169: In a PIM-SM network, which type of node helps to build a tre...; Question 170: You notice that a number of IGMP leave group messages are pa...; Question 171: You are setting up a new switch in your network that is usin...; Question 172: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 173: Which three PoE power allocation methods are supported on EX...; Question 174: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 175: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 176: You are asked to implement CoS on an EX Series switch. You a...; Question 177: Which statement is true about default BGP route redistributi...; Question 178: -- Exhibit -- user@SwitchA> show dot1x interface detail g...; Question 179: When enabling MVRP for dynamic VLAN registration, which thre...; Question 180: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 181: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 182: Which statement is true regarding OSPF multi-area adjacencie...; Question 183: -- Exhibit -- {master:0}[edit] user@router# show class-of-se...; Question 184: You must configure your access switch with more than 3000 VL...; Question 185: You are asked to set up 802.1X port authentication for all a...; Question 186: Which three attributes must a BGP update contain? (Choose th...; Question 187: -- Exhibit -- [edit protocols bgp] user@router# show group e...; Question 188: A company's security policy does not allow outside computers...; Question 189: -- Exhibit -- [edit class-of-service] drop-profiles { test-d...; Question 190: -- Exhibit -- {master:0}[edit] user@switch# show protocols v...; Question 191: Your company uses 802.1X to authenticate your users. You wan...; Question 192: You are asked to establish a single EBGP peering across two ...; Question 193: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 194: -- Exhibit -- user@router> show route protocol bgp detail...; Question 195: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 196: -- Exhibit -- user@switch> show configuration access radi...; Question 197: -- Exhibit -- [edit protocols vstp] 'vlan all' Cannot config...; Question 198: -- Exhibit -- ar 16 19:12:58.291474 BGP RECV 172.14.10.2+512...; Question 199: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 200: A Layer 2 transparent firewall separates two OSPFv3 routers....; Question 201: NetBIOS snooping information is stored in which database on ...; Question 202: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 203: You must configure a multifield classifier on ge-1/0/0. This...; Question 204: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 205: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 206: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...; Question 207: -- Exhibit -- user@router> show interfaces ge-0/0/0 exten...; Question 208: -- Exhibit -- Interface State Area DR ID BDR ID Nbrs em2.0 D...; Question 209: -- Exhibit - (Exhibit) -- Exhibit -- Click the Exhibit butto...

Question 160/209

LEAVE A REPLY

Download PDF File