<< Prev Question Next Question >>

Question 49/75

The OTN circuit board (such as ND2) of OSN 1800V can respond to the status of the indicator light on the panel to reflect the optical power of the local end too high or too low.

LEAVE A REPLY

Your email address will not be published. Required fields are marked *

Question List (75q)
Question 1: Which of the following paths are not related to the business...
Question 2: The following basic principles for fault location in WDM sys...
Question 3: Which of the following description of the process for optimi...
Question 4: In WDM systems, when using less than () wavelength, it is id...
Question 5: The following limitations of alarm and performance analysis ...
Question 6: The OSN 8800 device is protected by fan redundancy. When any...
Question 7: In the ROADM, which of the following layer of OTN paths do n...
Question 8: The following description of discrete services, which are co...
Question 9: Which of the following description of the extended ECC is co...
Question 10: The lower the noise figure of the amplifier, the less noise ...
Question 11: MG-SDH digital single core can be expanded by software upgra...
Question 12: For the relay type OTU, the alarms of all SM segments are te...
Question 13: Which of the following options can reduce the effects of non...
Question 14: During the process of maintaining the OSN device, it is ofte...
Question 15: The collection and storage of on-site data includes periodic...
Question 16: The wave division system complement to chromatic dispersion ...
Question 17: Which of the following technologies is the main difference b...
Question 18: Which of the following features does the EX40 add than X40?...
Question 19: Which particles can be cross-scheduled for the cross-board o...
Question 20: Before creating an optical cross-connection, you need to man...
Question 21: ODUk SNCP protection cannot be automatically switched. The p...
Question 22: Which of the following reasons does not cause optical power ...
Question 23: Which of the following IP addresses are not part of the priv...
Question 24: Which of the following reasons may cause a business error? (...
Question 25: The optical monitoring channel wavelength used by the ST2 bo...
Question 26: What common methods for MSTP device fault location can be su...
Question 27: Which of the following ROADN nodes are configured correct? (...
Question 28: The single-fiber bidirectional WDM system uses only one fibe...
Question 29: The reasons for the discrete business are? (Multiple choice)...
Question 30: Which of the following meters/boards can be used to test the...
Question 31: The OCh path is created using the single station method. Aft...
Question 32: What are the ways that NG WDM devices create fibers? (Multip...
Question 33: Which of the following description of the principle of autom...
Question 34: When 10-minute error-free test is performed on a certain wav...
Question 35: Which of the following description of ODUflex are correct? (...
Question 36: MPLS-TP is a subset of MIPLS that removes connectionless IP-...
Question 37: For a 10G OTU board, the receiving end optical module uses P...
Question 38: The following description of the PM_BIP8 related alarm, whic...
Question 39: The length range of the DATA field in the Ethernet frame str...
Question 40: FOADM includes parallel FOAD and serial FOADM, both supporti...
Question 41: Which of the following methods does the networking and appli...
Question 42: Which of the following operating modes does the AT8 board su...
Question 43: When using the OSN8800 T32, if you want to set the ID number...
Question 44: In general, which of the following operations will cause a s...
Question 45: The following is the client-side logical port of the board i...
Question 46: When the working channel of the optical line protection fail...
Question 47: When the OSN 8800 needs to access GE signals, the boards tha...
Question 48: Which of the following ROADM boards have WSS optical modules...
Question 49: The OTN circuit board (such as ND2) of OSN 1800V can respond...
Question 50: The OTS path refers to the physical fiber connection between...
Question 51: Which of the following statement is correct?...
Question 52: In the electrical layer overhead processing-sink function, t...
Question 53: Which of the following description of discrete services is c...
Question 54: Before querying the error and optical power on the network m...
Question 55: Which of the following description of the performance parame...
Question 56: TEM28 is the Ethernet convergence tributary board. Which of ...
Question 57: Daily equipment maintenance items, excluding:...
Question 58: Which of the following description of the DM12 board are cor...
Question 59: The following description of the cross-board of the OSN 8800...
Question 60: When the input optical power of the amplifier at the receivi...
Question 61: What does the component of the ASON network not include?...
Question 62: The following description of 1+1 and 1:1 optical line protec...
Question 63: Generally, in the NG WD system, the full-wave fiber input po...
Question 64: When creating an electric layer path, one RX/TX port can onl...
Question 65: If you want to establish a GE-level path on the NMS, which o...
Question 66: Since the EALC/ALC function is used in the SOM system, there...
Question 67: What are the classification of Ethernet performance tests? (...
Question 68: When configuring the Ethernet Layer 2 attribute, set the Def...
Question 69: When you delete a discrete service, you can first activate i...
Question 70: In 2.5G MSP ring composed of four MSTP sites, when protectio...
Question 71: Since the nonlinear effect is generated, its influence on th...
Question 72: The following description of the ASDN software structure, th...
Question 73: In WDM systems, when using less than () wavelength, it is id...
Question 74: Which of the following is the data that needs to be collecte...
Question 75: The transmission windows of 1310 nm and 1550 nm are low loss...