<< Prev Question Next Question >>

Question 4/66

A playbook contains five tasks in total. An administrator runs the playbook and four out of five tasks finish successfully, but one task fails. What will be the status of the playbook after it is run?

LEAVE A REPLY

Your email address will not be published. Required fields are marked *

Question List (66q)
Question 1: What are two effects of enabling auto-cache in a FortiAnalyz...
Question 2: On the RAID management page, the disk status is listed asIni...
Question 3: Which two statements are true regarding FortiAnalyzer log fo...
Question 4: A playbook contains five tasks in total. An administrator ru...
Question 5: If you upgrade your FortiAnalyzer firmware, what report elem...
Question 6: Which statement about the FortiSOAR management extension is ...
Question 7: Which statements are true regarding securing communications ...
Question 8: For which two SAML roles can the FortiAnalyzer be configured...
Question 9: Refer to the exhibit. (Exhibit) Based on the partial outputs...
Question 10: Which two settings must you configure on FortiAnalyzer to al...
Question 11: An administrator has configured the following settings: conf...
Question 12: View the exhibit. (Exhibit) What does the data point at 14:3...
Question 13: How can you configure FortiAnalyzer to permit administrator ...
Question 14: Refer to the exhibit. (Exhibit) What does the data point at ...
Question 15: What can the CLI command # diagnose test application oftpd 3...
Question 16: You are using RAID with a FortiAnalyzer that supports softwa...
Question 17: Which two statements about log forwarding are true? (Choose ...
Question 18: View the exhibit: (Exhibit) What does the 1000MB maximum for...
Question 19: Which two constraints can impact the amount of reserved disk...
Question 20: Which two statement are true regardless initial Logs sync an...
Question 21: What must you configure on FortiAnalyzer to upload a FortiAn...
Question 22: Which statement about the FortiSIEM management extension is ...
Question 23: Refer to the exhibit. (Exhibit) Laptopt is used by several a...
Question 24: Which statement is true when you are upgrading the firmware ...
Question 25: What FortiGate process caches logs when FortiAnalyzer is not...
Question 26: If the primary FortiAnalyzer in an HA cluster fails, how is ...
Question 27: After you have moved a registered logging device out of one ...
Question 28: An administrator has moved FortiGate A from the root ADOM to...
Question 29: What can you do on FortiAnalyzer to restrict administrative ...
Question 30: Which FortiAnalyzer feature allows you to use a proactive ap...
Question 31: What statements are true regarding disk log quota? (Choose t...
Question 32: Which FortiAnalyzer feature allows you to retrieve the archi...
Question 33: You've moved a registered logging device out of one ADOM and...
Question 34: In FortiAnalyzer's FormView, source and destination IP addre...
Question 35: When working with FortiAnalyzer reports, what is the purpose...
Question 36: Which two actions should an administrator take to view Compr...
Question 37: What is the recommended method of expanding disk space on a ...
Question 38: Why run the command diagnose sql status sqlplugind?...
Question 39: What is the best approach to handle a hard disk failure on a...
Question 40: Which two statements are true regarding high availability (H...
Question 41: Which two statements are true regarding ADOM modes? (Choose ...
Question 42: Which two methods can you use to send event notifications wh...
Question 43: Refer to the exhibit. (Exhibit) What is the purpose of using...
Question 44: If you upgrade the FortiAnalyzer firmware, which report elem...
Question 45: Refer to the exhibit. (Exhibit) What is the purpose of using...
Question 46: Which statement about sending notifications with incident up...
Question 47: When you perform a system backup, what does the backup confi...
Question 48: What statements are true regarding the "store and upload" lo...
Question 49: What is the purpose of employing RAID with FortiAnalyzer?...
Question 50: You need to upgrade your FortiAnalyzer firmware. What happen...
Question 51: After generating a report, you notice the information you we...
Question 52: What is the purpose of the following CLI command? (Exhibit)...
Question 53: You have recently grouped multiple FortiGate devices into a ...
Question 54: Consider the CLI command: (Exhibit) What is the purpose of t...
Question 55: A play book contains five tasks in total. An administrator e...
Question 56: Logs are being deleted from one of your ADOMs earlier that t...
Question 57: Which statement about the FortiSOAR management extension is ...
Question 58: Why should you use an NTP server on FortiAnalyzer and all re...
Question 59: What is the purpose of a predefined template on the FortiAna...
Question 60: Which statements are correct regarding FortiAnalyzer reports...
Question 61: What is the purpose of output variables?...
Question 62: Which clause is considered mandatory in SELECT statements us...
Question 63: View the exhibit. (Exhibit) Why is the total quota less than...
Question 64: Refer to the exhibit. (Exhibit) Which statement is correct r...
Question 65: Which two of the following must you configure on FortiAnalyz...
Question 66: How do you restrict an administrator's access to a subset of...