<< Prev Question Next Question >>

Question 86/88

Manual replication of saved images and configurations from the master MSM64i to the slave MSM64i on
the BlackDiamond 6804 is done with the synchronize command.
However execution of this command does not replicate the run-time configuration.
You must use the save configuration command to store the run-time configuration first.

LEAVE A REPLY

Your email address will not be published. Required fields are marked *

Question List (88q)
Question 1: Select the incorrect statement for PIM....
Question 2: In a stable OSPF network, all OSPF routers in the same area ...
Question 3: The IS-IS Routing Protocol has been developed in ISO to prov...
Question 4: The Skew time in VRRP is used to ensure that two back-up rou...
Question 5: In normal operation the master node in the EAPS ring blocks ...
Question 6: In Extreme Ware what is the normal ACL behavior for incoming...
Question 7: The following ExtremeWare components are required on Extreme...
Question 8: IGMP v1 supports the leave group message....
Question 9: Which of the following is the default ESRP priority setting ...
Question 10: _________ is an ESRP option that allow(s) multiple VLANs to ...
Question 11: What is the meaning of the IEEE 802.3 SNAP field in an Ether...
Question 12: On an Extreme Networks switch, how many bits comprise an OSP...
Question 13: Although you can specify sequence numbers for different ACL ...
Question 14: An OSPF router connected to a RIP network &amp; performing r...
Question 15: A stream of IP Multicast packets is addressed to...
Question 16: What are the differences between a Summit 48i and a Summit 4...
Question 17: The Alpine 3802 switch contains a 3-slot chasis that can be ...
Question 18: What are the advantage/s of using integrated IS-IS as a rout...
Question 19: Which of the following is not advertised in an OSPF Link Sta...
Question 20: What is true of a Rendezvous Point in PIM-DM?...
Question 21: Radius on Extreme Networks 'i" Chipset switches allows valid...
Question 22: In general IS-IS allows routing of both IP and OSI packets. ...
Question 23: When you create an ACL entry on Summit 48i switch it works i...
Question 24: How does an IGMP router learns about the existence of hosts ...
Question 25: The Address Resolution Protocol enables a device to learn a ...
Question 26: Which of the following items is included in a DVMRP routing ...
Question 27: When the CLI command show vlan corporate, is issued, the Pro...
Question 28: What mechanisms does a master node use to detect a failure i...
Question 29: In SLB, Port Translation Mode is similar to Translation Mode...
Question 30: SSH2 on Extreme Networks 'i' series chipset switches enables...
Question 31: in IS-IS level 1/2 routers act as border routers to their re...
Question 32: Which CLI command enables all multicast traffic to multicast...
Question 33: Extreme Networks "I" Chipset switches allows you to run simu...
Question 34: (Exhibit) According to accompanying diagram and ACL configur...
Question 35: On a RADIUS server you can distinguish between switch access...
Question 36: IS-IS routing uses two levels of hierarchical routing level ...
Question 37: Within VRRP the election process of becoming the master swit...
Question 38: A QoS policy is the result when you assign a traffic groupin...
Question 39: All Extreme switch products support the standard 802.1p prio...
Question 40: By default, the OSPF routerID for an Extreme switch is selec...
Question 41: A QoS profile determines into which hardware queue a frame i...
Question 42: By default all VLANs are assigned to QoS profile QP...
Question 43: When a PIM-SM router wants to receive a Multicast stream, it...
Question 44: Like OSPF stub areas, NSSA areas cannot be used as transit a...
Question 45: Select the statements that are true for IP multicast?...
Question 46: In PIM sparse mode the Bootstrap Router election is based on...
Question 47: The pre-empt option in VRRP is enabled by default on Extreme...
Question 48: In OSPF, the router type that is required to connect an area...
Question 49: What is the maximum number of ACL rules supported on an Extr...
Question 50: OSPF Hello packets are recognized by all routers in the same...
Question 51: The type of OSPF LSAs that are sent out within an automous s...
Question 52: What is the RP-set?
Question 53: The CLI Command configure ospf delete vlan all? Will do the ...
Question 54: Which of the following CLI commands could you use to determi...
Question 55: There is one ACL type supported by Extreme Networks switches...
Question 56: Is it possible to configure a single physical port into diff...
Question 57: The following CLI command is valid to advertise SLB virtual ...
Question 58: Select the correct statements related to IP Multicast?...
Question 59: Which statement is true about integrated IS-IS....
Question 60: What does IS-IS stand for?
Question 61: In SLB a virtual server cannot belong to the same VLAN as th...
Question 62: In a Summit 5i switch, a QoS policy is applied on a basis....
Question 63: When limit-learning is configured on a port and the limit is...
Question 64: When configuring a Summit 5i for OSPF routing, it is recomme...
Question 65: The integrated IS-IS protocol allows for mixing of IP-only,O...
Question 66: Unlike VRRP, the eExtreme Standby Router Protocol provides r...
Question 67: An IP-only IS-IS router (or "IP-only" router) is defined to ...
Question 68: The Summit 7i switch supports how many queues per interface?...
Question 69: What is the CLI command you would use to configure a VLAN to...
Question 70: Dealing with access control lists on Extreme Networks switch...
Question 71: When SSH2 is configured and enabled on a Summit 7i switch, t...
Question 72: OSPF requires that all areas attach directly to the backbone...
Question 73: An LSP is a link state packet used by which routing protocol...
Question 74: What is the function of a Bootstrap Router?...
Question 75: When you configure EAPS the following must apply....
Question 76: Dealing with an Access Control List on Extreme switches it's...
Question 77: Is it possible to create multicast STPD on a switch?...
Question 78: What is an IGP protocol other than OSPF that uses the Dijkst...
Question 79: A QoS building block that defines a class of service by spec...
Question 80: The default OSPF router dead interval for Extreme Networks s...
Question 81: Which CLI command would you use to configure vlan tracking t...
Question 82: DVMRP is similar to OSPF in that it is Link State based....
Question 83: VRRP is
Question 84: IP Version 6 has amongst other differences with IP Version 4...
Question 85: What configuration is send when you upload a configuration f...
Question 86: Manual replication of saved images and configurations from t...
Question 87: The DHCP, HTTP and RADIUS functions that are required for Ne...
Question 88: What does the abbreviation DVMRP stands for?...