<< Prev Question Next Question >>

Question 63/66

DRAG DROP
What is the correct sequence of steps for VMAX3 HYPERMAX OS FAST write operations?
Select and Place:

LEAVE A REPLY

Your email address will not be published. Required fields are marked *

Question List (66q)
Question 1: If a VMAX3 System Bay 1 can have two additional standby powe...
Question 2: Which power zone, outlet, and breaker is responsible for sup...
Question 3: When connecting to a VMAX3 system from the POS Work Tray loc...
Question 4: A customer needs to back up data from an EMC VMAX3 to a Data...
Question 5: What accurately describes the Director 1 boot drive in a VMA...
Question 6: What is used for vaulting on a VMAX3?...
Question 7: What is the load limit when the fork set is attached directl...
Question 8: When can D@RE be enabled on a VMAX 20K?...
Question 9: You have selected to run an MMCS-1 replacement from MMCS-2. ...
Question 10: When logging into a VMAX3 array, which management GUI will b...
Question 11: On a VMAX3, how many different user roles are available when...
Question 12: (Exhibit) What is the purpose of the blue triangles located ...
Question 13: Immediately after powering on a VMAX installation, you notic...
Question 14: Which component of a 60-drive DAE can the VMAX3 array back-e...
Question 15: How many CPU cores are found in a fully populated 8-engine V...
Question 16: You are inspecting a VMAX3 at a customer site. Which physica...
Question 17: What will support the SRDF/A Multi-Cycle mode when multiple ...
Question 18: What is a benefit of using TimeFinder SnapVX?...
Question 19: What is the maximum number of front-end ports for host conne...
Question 20: Which VMAX3 model(s) has a maximum cache, per engine, of 2 T...
Question 21: In a VMAX3, which type of CPU meets an EMC pre-determined Se...
Question 22: Which directory is used on the user laptop, in which the Sym...
Question 23: You are performing a spare replacement script after the EMC ...
Question 24: A customer has a VMAX with six engines and wants to add two ...
Question 25: (Exhibit) Based on the exhibit, what does the highlighted co...
Question 26: Which VMAX model can have up to eight engines (1 or 2 system...
Question 27: A customer wants to configure SRDF between two VMAX3 arrays ...
Question 28: You are working on a VMAX family array with a S/N Identifier...
Question 29: What is an advantage of using TimeFinder SnapVX over legacy ...
Question 30: Which SRDF mode uses both SRDF and TimeFinder to provide a p...
Question 31: You are connected to a VMAX or VMAX3 system using Simplified...
Question 32: Which tool can be used to beacon the light bar on a VMAX3?...
Question 33: What is the normal status of an R2 device on a VMAX3?...
Question 34: What is the maximum number of linked targets, per source, al...
Question 35: Which VMAX3 system bay component uses violet color-coded cab...
Question 36: What is the maximum host device size on a VMAX3?...
Question 37: Which director emulation consolidates various Enginuity func...
Question 38: Which application must be installed before launching the VMA...
2 commentQuestion 39: Which VMAX3 task is performed by the "Verify VMAX Setup" scr...
Question 40: Which two types of DAEs are available in all system bays of ...
Question 41: On a VMAX3, how many I/O module slots are available per dire...
Question 42: When servicing a dispersed VMAX3 array, what is the availabl...
Question 43: What is the maximum number of standard storage bays that can...
Question 44: DRAG DROP A customer has a 2-engine VMAX 40K and has purchas...
Question 45: Which VMAX family model uses the S/N Identifier 'x972'?...
Question 46: What is the maximum number of storage bays configurable on a...
Question 47: What accurately describes the planning and configuration con...
Question 48: What is the maximum distance from System Bay 1 that a dual e...
Question 49: In a VMAX3, what is the minimum number of DAEs required for ...
Question 50: What is the SPS hold-up time limitation in minutes?...
Question 51: Which method is used to gather STP data from a VMAX3?...
Question 52: In a VMAX3 bay configured with only one engine, to which com...
Question 53: Based on the exhibit, which directors are cabled to Ports 4 ...
Question 54: If you have added drive enclosures to a VMAX storage bay bri...
Question 55: Which SRDF recovery option allows for the transfer of invali...
Question 56: What is the maximum number of drives supported by a VMAX 20K...
Question 57: Which task is performed on a VMAX 40K when running the "Conf...
Question 58: (Exhibit) Based on the exhibit, which VMAX model will have t...
Question 59: A customer wants to create a large number of TimeFinder Snap...
Question 60: To obtain credentials for logging into a VMAX family array, ...
Question 61: Which TimeFinder SnapVX feature provides for the automatic t...
Question 62: What is the reason for the rear light bar on VMAX3 systems?...
Question 63: DRAG DROP What is the correct sequence of steps for VMAX3 HY...
Question 64: On a VMAX 10K (987), which DAEs support daisy chaining?...
Question 65: A VMAX3 running HYPERMAX OS has several internal emulations....
Question 66: You are working on a VMAX dual engine system bay that includ...