<< Prev Question Next Question >>

Question 50/134

This show output is from the S7 Cisco Metro Switch and the PE7 Cisco ASR 9000 Series Router. Which configuration change(s) is/are needed to bring the S7 FastEthernet 0/2 interface into the up/up state?
S7#show cdp neighbors<OUTPUT OMITTED> Device ID Local Intrfce Holdtme Capability Platform Port IDPE7 Fas 0/2 163 R ASR9K Ser Gig 0/0/0/0S78 Fas 0/23 146 S I ME- 3400E- Fas 0/21S8 Fas 0/21 178 S I ME-3400E- Fas 0/21 *Mar 20 21:28:02.177:
%ETHCNTR-3-HALF_DUX_COLLISION_EXCEED_THRESHOLD: Collisions at FastEthernet0/2 exceed threshold. Considered as loop-back.*Mar 20 21:28:02.177: %PM-4-ERR_DISABLE:
loopback error detected on Fa0/2, putting Fa0/2 in err-disable state*Mar 20 21:28:03.184:
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down S7#show interface fa0/2FastEthernet0/2 is down, line protocol is down (err-disabled) Hardware is Fast Ethernet, address is e8ba.70b5.6c04 (bia e8ba.70b5.6c04) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Half-duplex, 10Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:40, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy:
fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/ sec, 0 packets/sec 484423 packets input, 39349929 bytes, 0 no buffer Received 484423 broadcasts (167203 multicasts) 0 runts, 0 giants, 0 throttles 1 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 167203 multicast, 0 pause input 0 input packets with dribble condition detected 972398 packets output, 128931949 bytes, 0 underruns 0 output errors, 46 collisions, 4 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out RP/0/RSP0/CPU0:PE7#show interfaces gi0/0/0/0GigabitEthernet0/0/0/0 is down, line protocol is down Interface state transitions: 4 Hardware is GigabitEthernet, address is 4055.392f.40a8 (bia
4055.392f.40a8) Internet address is 192.168.107.70/24 MTU 1514 bytes, BW 100000 Kbit (Max:
100000 Kbit) reliability 255/255, txload 0/255, rxload 0/255 Encapsulation ARPA, Full-duplex, 100Mb/s, THD, link type is force-up output flow control is off, input flow control is off loopback not set, ARP type ARPA, ARP timeout 04:00:00 Last input 00:00:00, output 00:00:35 Last clearing of "show interface" counters never 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 972551 packets input, 128953765 bytes, 729 total input drops 172486 drops for unrecognized upper-level protocol Received 0 broadcast packets, 800781 multicast packets 0 runts, 0 giants, 0 throttles,
0 parity 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 484545 packets output, 39360900 bytes, 0 total output drops Output 317283 broadcast packets, 167262 multicast packets 0 output errors, 0 underruns, 0 applique, 0 resets 0 output buffer failures, 0 output buffers swapped out 4 carrier transitions

LEAVE A REPLY

Your email address will not be published. Required fields are marked *

Question List (134q)
Question 1: Which three statements about the ARP function are true? (Cho...
Question 2: You need to enable the "local-router" serial 0/0 connection ...
Question 3: What is the result of using the Cisco IOS copy tftp: run com...
Question 4: Select and Place: (Exhibit)
Question 5: Select and Place: (Exhibit)
Question 6: Which two statements about Cisco IOS XR NTP configuration ar...
Question 7: Currently, a Cisco IOS XR router is configured to send IP SL...
Question 8: Select and Place: (Exhibit)
Question 9: Given the subnet of 209.165.201.0/27, which subnet range wil...
Question 10: Which pair of mechanisms are often used together to allow dy...
Question 11: Given a ring topology, which loop prevention mechanism provi...
Question 12: What is the Cisco IOS command to export IPv6 flows to Collec...
Question 13: Which Cisco IOS CLI command is used to verify the speed and ...
Question 14: Which three physical lines can provide local or remote acces...
Question 15: Using VLSM, how many /30 subnets can be derived from a singl...
Question 16: Which Cisco IOS XR command is involved in enabling remote ac...
Question 17: (Exhibit) Hot Area: (Exhibit)
Question 18: Select and Place: (Exhibit)
Question 19: What two commands enable port security and allow the switch ...
Question 20: Which Cisco router feature allows multiple independent routi...
Question 21: Refer to the exhibit. (Exhibit) Which three statements about...
Question 22: Which component is integrated into the Cisco IPoDWDM interfa...
Question 23: (Exhibit)
Question 24: Select and Place: (Exhibit)
Question 25: What is the measurement of the Cisco IP SLA Operation ICMP P...
Question 26: A customer uses OSPF as their Customer Edge routing protocol...
Question 27: Which three statements about the Cisco IOS XR task-based use...
Question 28: What is the Cisco IOS command that is used to prevent the ro...
Question 29: What are the three RFC 1918 IPv4 private address ranges? (Ch...
Question 30: Refer to the exhibit. Real 53 Cisco 640-875 Exam (Exhibit) B...
Question 31: Refer to the exhibit. (Exhibit) Using a single Class C netwo...
Question 32: When two or more different routes exist to the same destinat...
Question 33: Which two statements about Packet over SONET are true? (Choo...
Question 34: What does a transparent LAN switch use to build its CAM tabl...
Question 35: The PE and CE interfaces are in the UP/UP state. The junior ...
Question 36: Refer to the exhibit. Which two statements are true regardin...
Question 37: Refer to the exhibit. Real 20 Cisco 640-875 Exam (Exhibit) G...
Question 38: Refer to the exhibit. (Exhibit) According to this show outpu...
Question 39: Which Cisco IOS XR command displays traffic counters for an ...
Question 40: Which two commands are required to enter enable mode on a co...
Question 41: Which layer of the OSI Model does Label Distribution Protoco...
Question 42: Refer to the exhibit. (Exhibit) Which configuration is neces...
Question 43: On Cisco IOS XR, for which purpose is the turboboot procedur...
Question 44: What is the minimum version of DOCSIS that will support IPv6...
Question 45: Which EIGRP feature in IOS, IOS-XE, and IOS-XR will prevent ...
Question 46: Which statement about 10/40/100 GigabitEthernet interface co...
Question 47: Which feature is used to protect the control plane of the ro...
Question 48: Generally, which way is the fastest to open S3 and S4 servic...
Question 49: Select and Place: (Exhibit)
Question 50: This show output is from the S7 Cisco Metro Switch and the P...
Question 51: Select and Place: (Exhibit)
Question 52: Select and Place: (Exhibit)
Question 53: What are two benefits of a star network topology? (Choose tw...
Question 54: Which three statements about Cisco Discovery Protocol operat...
Question 55: A network administrator issues the who command on a Cisco ro...
Question 56: A centralized DHCP server has been setup for customer use. W...
Question 57: Which of the following correctly pairs the dotted decimal su...
Question 58: With IPv6, for which purpose are router solicitation and rou...
Question 59: Given the CIDR address range of 200.165.160.0 to 200.165.191...
Question 60: What is the default spanning-tree mode of an NNI port on a C...
Question 61: Select and Place: (Exhibit)
Question 62: Refer to the exhibit. (Exhibit) Real 60 Cisco 640-875 Exam A...
Question 63: Refer to the exhibit. (Exhibit) Which two options are the nu...
Question 64: What are the four steps to enable SSH v1 and v2 server on Ci...
Question 65: A Network Engineer configured NAT for external access but on...
Question 66: A network engineer has been provided subnet 209.165.202.128/...
Question 67: Which best describes the relationship between user groups an...
Question 68: A network administrator set-up AAA on a new router. While th...
Question 69: You are having problems browsing to http://www.cisco.com fro...
Question 70: A Passive Optical Network is a point-to-multipoint FTTx netw...
Question 71: Which two applications require the network to have the least...
Question 72: (Exhibit) Hot Area: (Exhibit)
Question 73: Select and Place: (Exhibit)
Question 74: On Cisco IOS Switches, which port security violation mode re...
Question 75: Which Cisco IOS XR command presents a list of all interfaces...
Question 76: Which Cisco IOS XR command displays information about static...
Question 77: Which two statements about NetFlow support on Cisco IOS XR a...
Question 78: What is a the best way to secure the route processor on a Ci...
Question 79: If a bridge port is in the non-designated state, which two s...
Question 80: Which IPv6 feature replaced and enhanced the IPv4 ARP functi...
Question 81: Which three of the following components must be elected befo...
Question 82: Which multiplexing technology has minimal impact to producti...
Question 83: Select and Place: (Exhibit)
Question 84: Which Cisco IOS XR CLI command can you use to determine if t...
Question 85: Refer to the exhibit. Real 30 Cisco 640-875 Exam (Exhibit) R...
Question 86: Refer to the exhibit. (Exhibit) Which two options are the nu...
Question 87: Which three IP addresses are valid for hosts that belong to ...
Question 88: When EIGRP is enabled on Cisco IOS XR, which EIGRP feature i...
Question 89: A network engineer has configured an interface with various ...
Question 90: Select and Place: (Exhibit)
Question 91: Which is a valid IPv6 Link Local address?...
Question 92: Select and Place: (Exhibit)
Question 93: Given these four Class B networks: 172.104.0.0, 172.105.0.0,...
Question 94: Which two statements about IPv4 DHCP operations are true? (C...
Question 95: Which three statements correctly describe DSL-based Internet...
Question 96: Which Layer 2 WAN protocol uses DLCI as the virtual circuit ...
Question 97: Refer to the exhibit. (Exhibit) A new policy requires all co...
Question 98: What are three features present on both ICMPv4 and ICMPv6? (...
Question 99: Given the IP address of 209.168.200.155/27, which two option...
Question 100: Refer to the exhibit. (Exhibit) Which layer(s) of the TCP/IP...
Question 101: Which statement about STP operations is true?...
Question 102: Which two commands can be used to enable LACP when configuri...
Question 103: Select and Place: (Exhibit)
Question 104: Refer to the exhibit. (Exhibit) Which two statements about t...
Question 105: What is the SDH equivalent of the SONET STS-12 framing forma...
Question 106: The network administrator is using a Windows PC application ...
Question 107: What is the Cisco recommended way to secure SNMPv2 community...
Question 108: Select and Place: (Exhibit)
Question 109: Select and Place: (Exhibit)
Question 110: Which Cisco IOS XR CLI command displays the running state of...
Question 111: Refer to the exhibit. (Exhibit) Which statement about this s...
Question 112: Which two statements are correct regarding routing protocol ...
Question 113: Refer to the exhibit. (Exhibit) Real 46 Cisco 640-875 Exam Y...
Question 114: What is the term that refers to a device that has no Custome...
Question 115: Which three statements about Cisco IOS XR CLI operations are...
Question 116: Which option is enabled by default on Cisco IOS and IOS XE r...
Question 117: Given the IP address 10.106.170.145 255.248.0.0, which three...
Question 118: Which statement about IPv6 global unicast addresses is true?...
Question 119: Exhibit: (Exhibit) Select and Place: (Exhibit)...
Question 120: Select and Place: (Exhibit)
Question 121: Which two statements about classful or classless routing pro...
Question 122: Refer to the exhibit. (Exhibit) Company 1 has merged with Co...
Question 123: (Exhibit) Hot Area: (Exhibit)
Question 124: Which two statements about transparent bridging operations a...
Question 125: (Exhibit) Hot Area: (Exhibit)
Question 126: Select and Place: (Exhibit)
Question 127: Which two statements about Cisco IOS XE operations are true?...
Question 128: Which type of IPv6 address does the ff00::/8 prefix denote?...
Question 129: Select and Place: (Exhibit)
Question 130: Refer to the exhibit. (Exhibit) Host 3 on Network A is sendi...
Question 131: What is the size difference in bits between an IPv4 address ...
Question 132: Which statement about a root bridge in an STP domain is true...
Question 133: On Switch 5, which command would configure VLAN 5 as root?...
Question 134: Refer to the exhibit. (Exhibit) Robert is sending an instant...