400-051 Exam Dumps | You have implemented 5-digit forced authorization codes to all international route patterns on Cisco

<< Prev Question Next Question >>

Question 95/212

You have implemented 5-digit forced authorization codes to all international route patterns on Cisco Unified Communications Manager. Your users report that after entering the FAC codes, they must wait for more than 10 seconds before the call is routed.
Which procedure eliminates the wait time?

A. Configure a # (hash) sign to the end of the forced authorization codes to signal the end of dialing.

B. Go to the Cisco Unified Communications Manager Service Parameters and reduce the T-304 number to 5000 milliseconds.

C. Request your long distance telephone service provider to reduce the call setup time to 5 seconds.

D. Check and eliminate any existing route patterns that overlap with the international route pattern.

E. Educate the users to press # (hash) after entering the forced authorization codes.

Question List (212q): Question 1: When neither the active or standby Location Bandwidth Manage...; Question 2: Refer to the exhibit. (Exhibit) A user is going through a se...; Question 3: Which SIP header is used by Cisco Unified Communication Mana...; Question 4: Which message-handling behavior describes how Cisco Unity Co...; Question 5: Which two enterprise presence domains can federate with Cisc...; Question 6: You are assisting a customer to troubleshoot a SIP early-off...; Question 7: Which digital modulation method is used to transmit caller I...; Question 8: Refer to the exhibit. (Exhibit) How many calls, inbound and ...; Question 9: Which codec is supported on the Cisco PVDM2 DSP modules but ...; Question 10: Refer to the exhibit. (Exhibit) Assume the B-ACD configurati...; Question 11: Assume the IP address of Cisco Unity Express is 10.1.1.1. Wh...; Question 12: To which QoS tool category does compressed RTP belong?...; Question 13: Which two VoIP protocols use SDP to describe streaming media...; Question 14: In which call state does the Mobility soft key act as a togg...; Question 15: Which two statements describe characteristics of Binary Floo...; Question 16: A queued call has reached the maximum wait time configured f...; Question 17: Refer to the exhibit. (Exhibit) You received this debug outp...; Question 18: Which SIP response is considered a final response?...; Question 19: How many music on hold servers are required in a trunk-only ...; Question 20: Which H.245 information is exchanged within H.225 messages i...; Question 21: In addition to SIP triggers, which two trigger types can inv...; Question 22: Which two statements are requirements regarding hunt group o...; Question 23: Which two mechanisms does Cisco EnergyWise use for neighbor ...; Question 24: Which SIP reason phrase maps to SIP response reason code 181...; Question 25: In Key Press Markup Language, which SIP request is used to d...; Question 26: Which call processing feature overrides the Do Not Disturb s...; Question 27: Which two security services are provided by the Phone Proxy ...; Question 28: Which two statements about the Cisco UC on UCS specs-based v...; Question 29: According to ITU-T E.164 recommendations, which two fields i...; Question 30: When IP phone A was provisioned in a Cisco Unified Communica...; Question 31: Refer to the exhibit. (Exhibit) If this SIP call is initiate...; Question 32: Refer to the exhibit. (Exhibit) IP phone 1 has the MAC addre...; Question 33: Which statement describes the Cisco best practice recommenda...; Question 34: Which two SCCP call signaling messages are sent by an IP pho...; Question 35: Which call hunt mechanism is only supported by the voice hun...; Question 36: Company ABC is planning to migrate from MCS-hosted Cisco Uni...; Question 37: Which Cisco Unified Contact Center Express script media step...; Question 38: In a Cisco EnergyWise domain, which two terms describe a Cis...; Question 39: A Cisco Unity Connection administrator receives a name chang...; Question 40: Refer to the exhibit. (Exhibit) You received this debug outp...; Question 41: Which statement describes the supported integration method w...; Question 42: Refer to the exhibit. (Exhibit) The exhibit shows the Cisco ...; Question 43: Which element was added to H.225 messages to enable Fast Con...; Question 44: Which two host portion format conditions are true for direct...; Question 45: Which two categories are state-based greetings on Cisco Unit...; Question 46: Refer to the exhibit. (Exhibit) Three calls are active on ep...; Question 47: Router A and router B are Cisco IOS routers with hardware CF...; Question 48: What does a period accomplish when it is used in a SIP Dial ...; Question 49: Refer to the exhibit. (Exhibit) How many simultaneous outbou...; Question 50: Which statement about what happens to incoming calls to a Ci...; Question 51: Refer to the exhibit. (Exhibit) You received this debug outp...; Question 52: Refer to the exhibit. (Exhibit) Which option describes the m...; Question 53: When a Cisco IOS gatekeeper receives an ARQ from a registere...; Question 54: Refer to the exhibit. (Exhibit) A user is going through a se...; Question 55: When Single Inbox is configured, what will happen to an emai...; Question 56: Which external database software is required for the Cisco I...; Question 57: Assume 6 bytes for the Layer 2 header, 1 byte for the end-of...; Question 58: Refer to the exhibit. (Exhibit) All displayed devices are re...; Question 59: Which tag in the SIP header is used by Cisco Unified Communi...; Question 60: Which statement describes how the digit zero is handled in t...; Question 61: Which two statements describe security services that are pro...; Question 62: What is the maximum number of Cisco Unified Communications M...; Question 63: Which two applications can connect directly with a Cisco Uni...; Question 64: Which procedure uses H.225 messages to exchange H.245 Master...; Question 65: Refer to the exhibit. (Exhibit) In this high-availability Ci...; Question 66: Refer to the exhibit. (Exhibit) This output was captured on ...; Question 67: Which device is the initiator of a StationD message in a Cis...; Question 68: Assume a 30-millisecond voice payload, 6 bytes for the Layer...; Question 69: Which two responses are examples of client error responses i...; Question 70: Refer to the exhibit. (Exhibit) You received this debug outp...; Question 71: To which SIP response class do the SIP response codes 300 to...; Question 72: Refer to the exhibit. (Exhibit) A user is going through a se...; Question 73: Refer to the exhibit. (Exhibit) In an effort to troubleshoot...; Question 74: Which Call Control Discovery function allows the local Cisco...; Question 75: Refer to the exhibit. (Exhibit) Assuming this NFAS-enabled T...; Question 76: Which protocol that is used between Cisco IM and Presence an...; Question 77: Refer to the exhibit. (Exhibit) In this high-availability Ci...; Question 78: Which option is a characteristic of the Enhanced Location Ca...; Question 79: Which Cisco Unified Communications Manager deployment model ...; Question 80: Which two compression formats for high-definition video have...; Question 81: Which two Device Pool configuration settings will override t...; Question 82: Refer to the exhibit. (Exhibit) All displayed devices are re...; Question 83: Which statement about the effective path in the Enhanced Loc...; Question 84: Which capability is support by LLDP-MED but not by Cisco Dis...; Question 85: Which statement about system broadcast messages in Cisco Uni...; Question 86: In Channel Associated Signaling on a T1 circuit using Extend...; Question 87: Which capability is supported by Cisco Discovery Protocol bu...; Question 88: Refer to the exhibit. (Exhibit) Your customer sent you this ...; Question 89: Which Device Pool configuration setting will override the de...; Question 90: Refer to the exhibit. (Exhibit) A user is going through a se...; Question 91: Which statement about what happens to a hunt member who does...; Question 92: What is the maximum one-way delay, in milliseconds, between ...; Question 93: Which ITU-T recommendation defines the procedures for using ...; Question 94: Which SIP request method enables reliability of SIP 1xx resp...; Question 95: You have implemented 5-digit forced authorization codes to a...; Question 96: Refer to the exhibit. (Exhibit) Assume the B-ACD configurati...; Question 97: To which Cisco enterprise medianet application class does Ci...; Question 98: The iLBC codec operates at 38 bytes per sample per 20-millis...; Question 99: Refer to the exhibit. (Exhibit) How many simultaneous inboun...; Question 100: What is the maximum length of any numeric geographic area ad...; Question 101: Refer to the exhibit. (Exhibit) Which ds0-group option shoul...; Question 102: What does a comma accomplish when it is used in a SIP Dial R...; Question 103: Refer to the exhibit. (Exhibit) Which DTMF relay method is a...; Question 104: Which statement about G.722.1 codec support on Cisco Unified...; Question 105: Refer to the exhibit. (Exhibit) Assume that the serial inter...; Question 106: Which protocol does the Cisco Jabber client use, in conjunct...; Question 107: Which RAS message is used between two gatekeepers to resolve...; Question 108: A company that is using the Cisco Unified Contact Center Exp...; Question 109: Which Cisco Unified Contact Center Express data store contai...; Question 110: Which Call Admission Control mechanism is supported for the ...; Question 111: Which method allows administrators to determine the best mat...; Question 112: In Cisco IOS routers, which chipset is the PVDM-12 DSP hardw...; Question 113: Which two Cisco Unified Communications Manager SIP profile c...; Question 114: Refer to the exhibit. (Exhibit) If this SIP call is initiate...; Question 115: Which message is used by a Cisco Unified Communications Mana...; Question 116: How many destinations can be configured for a SIP trunk on a...; Question 117: Which Cisco IM and Presence service is responsible for loggi...; Question 118: Refer to the exhibit. (Exhibit) During a QSIG tunneling over...; Question 119: Refer to the exhibit. (Exhibit) A user is going through a se...; Question 120: Which statement describes the question mark wildcard charact...; Question 121: Which type of mailbox on Cisco Unity Express can play a user...; Question 122: Which two data frame lengths are supported by iLBC? (Choose ...; Question 123: Which definition is included in a Cisco UC on UCS TRC?...; Question 124: What is the maximum number of call-processing subscribers in...; Question 125: Which two applications must be connected to a leaf cluster i...; Question 126: Which two types of line codes are configurable for an E1 PRI...; Question 127: Refer to the exhibit. (Exhibit) A user is going through a se...; Question 128: Which Cisco Unified Contact Center Express data store contai...; Question 129: Which message is used by a Cisco IOS MGCP gateway to send pe...; Question 130: Which statement describes the key security service that is p...; Question 131: What is the number of directory URIs with which a Cisco Unif...; Question 132: Which statement about a virtual SNR DN-configured Cisco Unif...; Question 133: Which two types of devices on Cisco Unified Communications M...; Question 134: Refer to the exhibit. (Exhibit) All displayed devices are re...; Question 135: Which protocol is used by presence-enabled users in Cisco IM...; Question 136: Which codec complexity mode, when deployed on Cisco IOS rout...; Question 137: Which two SDP content headers can be found in a SIP INVITE m...; Question 138: In Cisco IOS routers, which chipset is the PVDM2-32 DSP hard...; Question 139: Which statement about Cisco EnergyWise domain member neighbo...; Question 140: Refer to the exhibit. (Exhibit) Assume the B-ACD configurati...; Question 141: Refer to the exhibit. (Exhibit) How many inbound calls can b...; Question 142: Refer to the exhibit. (Exhibit) Ephone 1 has three active ca...; Question 143: Refer to the exhibit. (Exhibit) How many SIP signaling dialo...; Question 144: Refer to the exhibit. (Exhibit) Which ephone-dn can join the...; Question 145: Which SIP message element is mapped to QSIG FACILITY message...; Question 146: Refer to the exhibit. (Exhibit) Which ds0-group option shoul...; Question 147: Refer to the exhibit. (Exhibit) Assuming that the administra...; Question 148: Refer to the exhibit. (Exhibit) The exhibit shows the Cisco ...; Question 149: Which statement describes the external database requirement ...; Question 150: In a Cisco Unified Communications Manager design where +E.16...; Question 151: Which two SCCP call signaling messages are initiated by Cisc...; Question 152: Which two statements about using the Load Server option for ...; Question 153: Which two user portion format conditions are true for direct...; Question 154: Which design restriction applies to Cisco Unified Communicat...; Question 155: Which statement describes a disadvantage of using the Cisco ...; Question 156: What is the minimum number of TCP sessions needed to complet...; Question 157: Assume 18 bytes for the Layer 2 header and a 10-millisecond ...; Question 158: Refer to the exhibit. (Exhibit) If this SIP call is initiate...; Question 159: Which definition is included in a Cisco UC on UCS TRC?...; Question 160: Which two statements describe characteristics of Cisco Unifi...; Question 161: Which two statements about the Peer Firmware Sharing option ...; Question 162: Refer to the exhibit. (Exhibit) Assuming that the administra...; Question 163: What is the name of the logical channel proposal that is tra...; Question 164: Which configuration parameter defines whether or not the use...; Question 165: Refer to the exhibit. (Exhibit) Which SIP response message s...; Question 166: Refer to the exhibit. (Exhibit) A user is performing a serie...; Question 167: To which Cisco enterprise medianet application class does Ci...; Question 168: Refer to the exhibit. (Exhibit) Which SIP message header is ...; Question 169: How are queues serviced in Cisco IOS routers with the CBWFQ ...; Question 170: Refer to the exhibit. (Exhibit) Assume that the serial inter...; Question 171: Refer to the exhibit. (Exhibit) IP phone 1 has MAC address o...; Question 172: Refer to the exhibit. (Exhibit) All displayed devices are re...; Question 173: What is the default treatment of a message that is left in t...; Question 174: Refer to the exhibit. (Exhibit) How many SIP signaling trans...; Question 175: Which two call processing features have a lower priority tha...; Question 176: Refer to the exhibit. (Exhibit) Which SIP trunk deployment m...; Question 177: Which protocol does the Cisco Prime LAN Management Solution ...; Question 178: To which SIP response category does 301 Moved Permanently be...; Question 179: Which four attributes are needed to determine the time to co...; Question 180: Which Cisco Unified Communications Manager Express ephone bu...; Question 181: When a Cisco IOS gatekeeper receives an LRQ, what is the fir...; Question 182: Which Cisco Unified Communications Manager partition will be...; Question 183: Which Cisco Unified Contact Center Express core system softw...; Question 184: When multiple greetings are enabled on Cisco Unity Express, ...; Question 185: Which two statements describe the remote supervisory monitor...; Question 186: Refer to the exhibit. (Exhibit) IP phone 1 has MAC address o...; Question 187: Which statement about accessing secure Cisco Unity Connectio...; Question 188: Which mechanism enables the Cisco Unified CCX Cisco Agent De...; Question 189: Which entity signs a Cisco IP phone LSC?...; Question 190: In Cisco IOS routers that use low latency queuing, which alg...; Question 191: Which configuration component in Cisco Unified Communication...; Question 192: When Cisco Unity Connection users attempt to connect using W...; Question 193: Which SIP request is used by a Cisco 9971 IP Phone to signal...; Question 194: Which two Cisco Unified Communications Manager Express hunt ...; Question 195: What does a weight represent in the Enhanced Location Call A...; Question 196: When DSP oversubscription occurs on a Cisco IOS router using...; Question 197: Assume 20 bytes of voice payload, 6 bytes for the Layer 2 he...; Question 198: Which statement describes the Maximum Serving Count service ...; Question 199: Which statement describes DTMF processing on Cisco Unified C...; Question 200: Which two analog telephony signaling methods are most vulner...; Question 201: Which system location is used for intercluster Enhanced Loca...; Question 202: Which Cisco Unity Connection call handler message is played ...; Question 203: Which three Cisco Unity Connection call handler greetings ca...; Question 204: Which statement about the iSAC on Cisco Unified Border Eleme...; Question 205: Which statement about application inspection of SAF network ...; Question 206: Which SIP request is used by Cisco Unified Communications Ma...; Question 207: What is the amount of audio bandwidth, in kilobits per secon...; Question 208: Which device is the initiator of a StationInit message in a ...; Question 209: How many RTP streams exist on the network when a Cisco Unifi...; Question 210: Refer to the exhibit. (Exhibit) From this NFAS-enabled T1 PR...; Question 211: What is the minimum number of H.225 messages required to est...; Question 212: How many signaling bits are there in each T1 time slot using...

Question 95/212

LEAVE A REPLY

Download PDF File