350-601 Exam Dumps | A server engineer wants to control power usage on a Cisco UCS C-Series rack server down to the component

<< Prev Question Next Question >>

Question 14/330

A server engineer wants to control power usage on a Cisco UCS C-Series rack server down to the component level.
Which two components support specific power limits? (Choose two.)

A. storage controller

B. network controller

C. processor

D. graphic card

E. memory

Question List (330q): Question 1: A storage engineer must configure zoning on a Cisco MDS 9000...; Question 2: Refer to the exhibit. (Exhibit) What is a characteristic of ...; Question 3: An engineer must configure Cisco IMC server management NIC f...; Question 4: An engineer must configure OSPF in the data center. The exte...; Question 5: Which two actions should be taken before an upgrade is start...; Question 6: An engineer is configuring VNTag between a virtualized serve...; Question 7: Which two statements describe about modifying Cisco UCS user...; Question 8: An engineer must implement protection against ICMP DoS attac...; Question 9: A cisco Nexus 9000 series switch experiences a startup confi...; Question 10: An engineer configures the netflow feature on a Cisco NX-OS ...; Question 11: Refer to the exhibit. (Exhibit) What is configured as a resu...; Question 12: Port security is statically configured on a Cisco Nexus 7700...; Question 13: Refer to the exhibit. (Exhibit) An engineer is configuring a...; Question 14: A server engineer wants to control power usage on a Cisco UC...; Question 15: An engineer is implementing NPV mode on a Cisco MDS 9000 Ser...; Question 16: An engineer must implement private VLANs for a group of Cisc...; Question 17: A network engineer must implement RBAC on Cisco MDS 9000 Ser...; Question 18: Refer to the exhibit. (Exhibit) Which VLANs are capable to b...; Question 19: Refer to the exhibit. (Exhibit) An engineer configures FCIP ...; Question 20: A DNS server with IP address 192.168.1.1 is deployed in a da...; Question 21: Which two authentication types does Cisco UCS Manager suppor...; Question 22: (Exhibit) Refer to the exhibit A network engineer must run a...; Question 23: Refer to the exhibit. (Exhibit) Cisco Fabric Services is ena...; Question 24: What is the benefit of adding Cisco HyperFlex Hardware Accel...; Question 25: An engineer mus! configure the remote SSH management connect...; Question 26: Drag and drop the fields for configuring a full state backup...; Question 27: A network engineer must implement RBAC on Cisco MDS 9000 Ser...; Question 28: When the default firmware package is set a new version, whic...; Question 29: An engineer is asked to modify an overridden policy by chang...; Question 30: Refer to the exhibit. (Exhibit) Refer to the exhibits An eng...; Question 31: An engineer must recover configuration on a Cisco MDS 9000 S...; Question 32: An engineer must shut down the Ethernet 1/2 interface when t...; Question 33: Refer to the exhibit. (Exhibit) What must be connected to cl...; Question 34: An engineer performs a Cisco UCS C480 ML M5 installation fro...; Question 35: Which two statements about the process of performing an EPLD...; Question 36: An engineer must configure RBAC in Cisco UCS Manager in an e...; Question 37: Refer to the exhibit. (Exhibit) An engineer is implementing ...; Question 38: Which two configuration settings are available in the in the...; Question 39: An engineer is performing a configuration on a Cisco Nexus 5...; Question 40: The engineer must configure SPAN on a cisco Nexus 5000 Serie...; Question 41: An engineer is implementing security on the Cisco MDS 9000 s...; Question 42: An engineer must implement a new VRF that permits communicat...; Question 43: Refer to the exhibit. (Exhibit) Which two Cisco UCS componen...; Question 44: An engineer must ensure fabric redundancy when implementing ...; Question 45: A network engineer is asked to describe the cloud infrastruc...; Question 46: Refer to the exhibit. (Exhibit) What is the result of this s...; Question 47: A customer reports Fibre Channel login requests to a cisco M...; Question 48: An engineer must apply AAA configuration on a Cisco MDS 9000...; Question 49: An engineer is implementing NetFlow on a Cisco Nexus 7000 Se...; Question 50: Due to a domain name change at a customer site, a Cisco UCS ...; Question 51: Refer to the exhibit. (Exhibit) Refer to the exhibit. Which ...; Question 52: An engineer configured an environment that contains the vPC ...; Question 53: An engineer needs to create a new user in the local user dat...; Question 54: An engineer upgrades the bash on the Cisco Nexus 9000 Series...; Question 55: A network engineer repeatedly saves a configuration on Catal...; Question 56: An engineer is configuring a backup operation on the existin...; Question 57: What are two requirements when planning a Cisco HyperFlex Al...; Question 58: Refer to the exhibit. (Exhibit) Refer to the exhibit. A user...; Question 59: Which adjacency server configuration makes two OTV edge devi...; Question 60: A network engineer must restore the running configuration on...; Question 61: An engineer must configure the order in which the server att...; Question 62: A Cisco MDS 9000 Series Switch is configured for SAN Analyti...; Question 63: An engineer must configure remote authentication on a Cisco ...; Question 64: Which two actions should be taken before an upgrade is start...; Question 65: An engineer changed a configuration and must perform a rollb...; Question 66: An engineer is duplicating an existing Cisco UCS setup at a ...; Question 67: What is a benefit of using Cisco Tetration?...; Question 68: Which configuration implements static ingress replication? (...; Question 69: Refer to the exhibit. (Exhibit) What is the result of implem...; Question 70: A Cisco UCS C-Series server is installed at a data center. T...; Question 71: A network administrator is creating a custom Django self-ser...; Question 72: A host EPG Client wants to talk to a webserver in EGP Web. A...; Question 73: What is a characteristic of the install all command on the c...; Question 74: Drag and drop the characteristics from the left onto the cor...; Question 75: An engineer must configure SAN connectivity in Cisco UCS man...; Question 76: Drag and drop the network assurance concepts from the left o...; Question 77: Refer to the exhibit. (Exhibit) Refer to the exhibit. What i...; Question 78: Refer to the exhibit. (Exhibit) Cisco Fabric Services is ena...; Question 79: Drag and drop the characteristics from the left onto the NAS...; Question 80: Refer to the exhibit. (Exhibit) Which statement about the de...; Question 81: What is the benefit of adding Cisco HyperFlex Hardware Accel...; Question 82: Several production and development database servers exist in...; Question 83: Refer to the exhibit. (Exhibit) An engineer must configure F...; Question 84: A Cisco UCS user called "Employee1" accidentally changed the...; Question 85: Refer to the exhibit. (Exhibit) A network engineer is settin...; Question 86: Refer to the exhibit. VLAN 10 Is experiencing delays and pac...; Question 87: Refer to the exhibit. (Exhibit) Which type of backup is requ...; Question 88: An engineer wants to create a backup of Cisco UCS Manager fo...; Question 89: Which data structure results from running this Python code? ...; Question 90: AN engineer enters these commands while in EEM on a Cisco Ne...; Question 91: An engineer is configuring a vHBA template in UCS Manager. T...; Question 92: Which two hypervisors does Cisco HyperFlex support? (Choose ...; Question 93: Which statement is true about upgrading the firmware on a Ci...; Question 94: An engineer is converting a Cisco MDS switch to support NPIV...; Question 95: Refer to the exhibit. (Exhibit) Why does the python code for...; Question 96: An engineer must configure a control plane policy on a Cisco...; Question 97: Drag and drop the storage technologies from the left onto th...; Question 98: An engineer must configure Cisco Nexus 9000 Series Switches ...; Question 99: (Exhibit) Refer to the exhibit. An engineer must monitor the...; Question 100: Refer to the exhibit. (Exhibit) What is a characteristic of ...; Question 101: An engineer is asked to manage a large-scale data center and...; Question 102: Which statement about the MAC address that the FCoE Initiali...; Question 103: An engineer performs a set of configuration changes for the ...; Question 104: An engineer must configure two Cisco Nexus 7000 series switc...; Question 105: Refer to the exhibit. (Exhibit) What is the result of implem...; Question 106: Refer to the exhibit. (Exhibit) Which action is taken to ens...; Question 107: Refer to the exhibit. (Exhibit) Why does the python code for...; Question 108: Refer to the exhibit. (Exhibit) What is the reason the syste...; Question 109: Refer to Exhibit: (Exhibit) An engineer must use the python ...; Question 110: What is a benefit of independent resource scaling in Cisco H...; Question 111: Refer to the exhibit. (Exhibit) An engineer must configure F...; Question 112: An engineer is implementing Cisco Intersight in a secure env...; Question 113: Where does the witness VM reside in a Cisco Hyperflex Edge d...; Question 114: An engineer is configuring VNTag between a virtualized serve...; Question 115: (Exhibit) Refer to the exhibit. Esxi-server is associated to...; Question 116: Which two actions are needed to configure a single Cisco API...; Question 117: An engineer must configure a Nexus 7000 series switch for HS...; Question 118: Refer to the exhibit. (Exhibit) An engineer configures FCIP ...; Question 119: An engineer is implementing FCoE. Which aspect of DCBXP on a...; Question 120: Refer to the exhibit. (Exhibit) Which VLANs are capable to b...; Question 121: An engineer must implement an automation solution to allow t...; Question 122: Which feature Is supported with an In-Service Software Upgra...; Question 123: Due to a major version change, an engineer must perform a so...; Question 124: Refer to the exhibit. (Exhibit) The STP priority of N7K-1 an...; Question 125: What is a recommended design choice in a topology for multip...; Question 126: What are two types of FC/FCoE oversubscription ratios? (Choo...; Question 127: Refer to the exhibit. (Exhibit) Refer to the exhibit. A deve...; Question 128: Refer to the exhibit. (Exhibit) What is the result of implem...; Question 129: Refer to the exhibit. (Exhibit) A flapping link issue has be...; Question 130: Refer to the exhibit. (Exhibit) An engineer needs to impleme...; Question 131: An engineer must implement a Cisco UCS system at a customer ...; Question 132: The Cisco Nexus switch Generic Online Diagnostics policy for...; Question 133: Refer to the exhibit. (Exhibit) Refer to the exhibit During ...; Question 134: What is the benefit of adding Cisco HyperFlex Hardware Accel...; Question 135: Refer to the exhibit. (Exhibit) Refer to the exhibit The com...; Question 136: An engineer is implementing NPV mode on a Cisco MDS 9000 Ser...; Question 137: Where is the witness deployed in a two-node Cisco HyperFlex ...; Question 138: A network engineer must enable port security on all cisco MD...; Question 139: An engineer implements a Cisco UCS C-Series Server that must...; Question 140: Which two statements about the process of upgrading an EPLD ...; Question 141: DRAG DROP Drag and drop the storage technologies from the le...; Question 142: Refer to the exhibit. (Exhibit) The STP priority of N7K-1 an...; Question 143: Refer to the exhibit. (Exhibit) An engineer configures FCIP ...; Question 144: A network engineer repeatedly saves a configuration on Catal...; Question 145: Drag and drop the NAS features from the left onto the NAS de...; Question 146: What happens to the default host firmware policy after a Cis...; Question 147: A network engineer must configure a Fibre Channel port monit...; Question 148: A customer reports Fibre Channel login requests to a cisco M...; Question 149: Which method must a network engineer use to upgrade the BIOS...; Question 150: A customer asks an engineer to develop a framework that will...; Question 151: An engineer must configure remote authentication on a Cisco ...; Question 152: An engineer creates a service profile in Cisco UCS Manager a...; Question 153: Refer to the exhibit. (Exhibit) What is the reason the syste...; Question 154: Which adjacency server configuration makes two OTV edge devi...; Question 155: Drag and drop the network assurance concepts from the left o...; Question 156: Refer to the exhibit. (Exhibit) An engineer must distribute ...; Question 157: Refer to the exhibit. (Exhibit) Which statement about the ER...; Question 158: Refer to the exhibit. (Exhibit) A network engineer must conf...; Question 159: (Exhibit) Refer to the exhibit. Which feature must be used t...; Question 160: An engineer is configuring VNTag between a virtualized serve...; Question 161: Refer to the exhibit. (Exhibit) Which type of backup is requ...; Question 162: An engineer installed a new Nexus switch with the mgm0 inter...; Question 163: Refer to the exhibit. (Exhibit) Which action is taken to ens...; Question 164: The engineer must configure SPAN on a Cisco Nexus 5000 Serie...; Question 165: An engineer implements SPAN configuration on an Nexus 5000 s...; Question 166: Refer to the exhibit. (Exhibit) An engineer configures FCIP ...; Question 167: Refer to the exhibit. (Exhibit) Which two Cisco UCS componen...; Question 168: A network architect considers a Cisco HyperFlex design solut...; Question 169: An engineer is enabling port security on a Cisco MDS 9000 Se...; Question 170: An engineer changed a configuration and must perform a rollb...; Question 171: A network architect is asked to design and manage geographic...; Question 172: An engineer must configure a Cisco MDS 9000 Series Switch fo...; Question 173: Refer to the exhibit. (Exhibit) Refer to the exhibit A netwo...; Question 174: Which server policy is used to install new Cisco IMC softwar...; Question 175: An engineer must shut down the Ethernet 1/2 interface when t...; Question 176: An engineer has a primary fabric that is named UCS-A and a s...; Question 177: A Cisco MDS 9000 Series Storage Switch has reloaded unexpect...; Question 178: What happens to the default host firmware policy after a Cis...; Question 179: Refer to the exhibit. (Exhibit) Which setting must be config...; Question 180: An engineer installed a new Nexus switch with the mgm0interf...; Question 181: Refer to the exhibit. (Exhibit) An engineer configures port ...; Question 182: A customer requires a solution to orchestrate the configurat...; Question 183: Drag and drop the storage technologies from the left onto th...; Question 184: Drag and drop the characteristics from the left onto the NAS...; Question 185: An engineer must start a software upgrade on a Cisco Nexus 5...; Question 186: An engineer has a primary fabric that is named UCS-A and a s...; Question 187: A network administrator must configure an extra keyring in C...; Question 188: Refer to the exhibit. (Exhibit) What is the outcome of this ...; Question 189: A network engineer must configure FCoE on an interface of a ...; Question 190: A network engineer must implement RBAC on Cisco MDS 9000 Ser...; Question 191: An engineer must apply AAA configuration on a Cisco MDS 9000...; Question 192: Refer to the exhibit. (Exhibit) Service degradation is repor...; Question 193: Which statement about the MAC address that the FCoE Initiali...; Question 194: (Exhibit) Refer to the exhibit. Which feature set must be us...; Question 195: Which server policy is used to install new Cisco IMC softwar...; Question 196: Refer to the exhibit. (Exhibit) Which configuration ensure t...; Question 197: An engineer deploys a new Cisco Nexus 5000 Series Switch in ...; Question 198: A host in EPG Client wants to talk to a webserver in EPG Web...; Question 199: Which two statements about the process of upgrading an EPLD ...; Question 200: The engineer must configure SPAN on a cisco Nexus 5000 Serie...; Question 201: A network engineer must download a firmware image from a rem...; Question 202: Drag and drop the mechanisms to collect data from a network ...; Question 203: Refer to the exhibit. (Exhibit) Which backup operation type ...; Question 204: Refer to the exhibit. (Exhibit) Cisco Fabric Services is ena...; Question 205: A network engineer an EPLD update on the fan modules of a Ci...; Question 206: A network architect wants to propose a scalable network moni...; Question 207: A small remote office is set to connect to the regional hub ...; Question 208: (Exhibit) Refer to the exhibit. An engineer must monitor the...; Question 209: Which configuration generates a syslog message when CPU util...; Question 210: Refer to the exhibit. (Exhibit) A network engineer must conf...; Question 211: An engineer updated firmware on Fabric Interconnects and act...; Question 212: A UCS B- Series server located in B5108 chassis 1 slot 1 is ...; Question 213: A cisco Nexus 9000 series switch experiences a startup confi...; Question 214: Refer to the exhibit. (Exhibit) Refer to the exhibit. A secu...; Question 215: An engineer needs to connect Cisco UCS Manager to an externa...; Question 216: Refer to the exhibit. (Exhibit) An engineer needs to impleme...; Question 217: An engineer is configuring a vHBA template in UCS Manager. T...; Question 218: An engineer is converting a Cisco MDS switch to support NPIV...; Question 219: Host 1 is in VLAN 100 located is DataCenter 1 and Host2 is i...; Question 220: A network administrator must automate the process of pinging...; Question 221: Which configuration statically assigns VSAN membership to a ...; Question 222: An engineer must configure a Nexus 7000 series switch for HS...; Question 223: A network engineer needs to upgrade the EPLDs of the fabric ...; Question 224: When a strict CoPP policy is implemented, which statement de...; Question 225: An engineer must migrate a Cisco UCS C-Series server from Ci...; Question 226: An engineer needs to Implement a solution that prevents loop...; Question 227: Which data interchange format is presented in this output? (...; Question 228: Drag and drop the storage technologies from the left onto th...; Question 229: An engineer is implementing security on the Cisco MDS 9000 s...; Question 230: The EPLD update of the supervisor module has been scheduled ...; Question 231: Refer to the exhibit. (Exhibit) An engineer needs to impleme...; Question 232: Where is the witness deployed in a two-node Cisco HyperFlex ...; Question 233: A customer has a requirement for an automation solution that...; Question 234: Which statement describes monitoring Fibre Channel traffic o...; Question 235: Which two statements describe the process of upgrading an EP...; Question 236: Refer to the exhibit. (Exhibit) Which two statements about t...; Question 237: Refer to the exhibit. (Exhibit) What is the result of this s...; Question 238: Port security is enabled on a Cisco MDS 9000 Series Switch. ...; Question 239: Refer to the exhibit. (Exhibit) An engineer is configuring a...; Question 240: A customer wants to offload some of its order processing to ...; Question 241: Drag and drop the NAS features from the left onto the NAS de...; Question 242: (Exhibit) Refer to the exhibit. Which command needs to be ad...; Question 243: Refer to the exhibit. (Exhibit) What is the result of implem...; Question 244: Drag and drop the storage technologies from the left onto th...; Question 245: Drag and drop the characteristics from the left onto the cor...; Question 246: An engineer is implementing traffic monitoring for a server ...; Question 247: Which MAC address is an HSRP version 2?...; Question 248: An engineer is configuring VNTag between a virtualized serve...; Question 249: Refer to the exhibit. (Exhibit) Which action must be taken b...; Question 250: An environment consists of a Cisco MDS 9000 Series Switch th...; Question 251: Which two actions must be taken to directly connect a Fibre ...; Question 252: Refer to the exhibit. (Exhibit) Refer to the exhibit. A netw...; Question 253: Which configuration generates a syslog message when CPU util...; Question 254: An engineer is implementing NPV mode on a Cisco MDS 9000 Ser...; Question 255: An engineer needs to perform a backup of user roles and loca...; Question 256: An engineer needs to implement a solution that will provide ...; Question 257: Refer to the exhibit. (Exhibit) Which statement about the de...; Question 258: Refer to the exhibit. (Exhibit) Which setting must be config...; Question 259: A network engineer must implement a telemetry solution to co...; Question 260: (Exhibit) Refer to the exhibit. Which information must be ad...; Question 261: A Cisco ACI engineer must configure an access port on a Cisc...; Question 262: Refer to the exhibit. (Exhibit) Which two Cisco UCS componen...; Question 263: What happens to the default host firmware policy after a Cis...; Question 264: Drag and drop the Hyperflex characteristics from the left on...; Question 265: Which statement is true about upgrading the firmware on a Ci...; Question 266: An engineer must configure OSPF in the data center. The exte...; Question 267: A network administrator must create a Linux container on a C...; Question 268: Refer to the exhibit. (Exhibit) Which two Cisco UCS componen...; Question 269: A network engineer must restore the running configuration on...; Question 270: An engineer is performing a configuration on a Cisco Nexus 5...; Question 271: Drag and drop the mechanisms to collect data from a network ...; Question 272: What is a characteristic of the install all command on the c...; Question 273: An engineer is implementing NetFlow on a Cisco Nexus 7000 Se...; Question 274: (Exhibit) Refer to the exhibit. All switches are configured ...; Question 275: An engineer is seeking the most optimal on demand CPU perfor...; Question 276: An engineer is asked to use SaaS to manage Cisco computing. ...; Question 277: An engineer installed a new Nexus switch with the mgm0interf...; Question 278: An engineer must configure multiple EPGs on a single access ...; Question 279: Refer to the exhibit. (Exhibit) An engineer is configuring a...; Question 280: The EPLD update of the supervisor module has been scheduled ...; Question 281: Refer to the exhibit. (Exhibit) Which command is run from th...; Question 282: Drag and drop the NAS features from the left onto the NAS de...; Question 283: Which two settings must be configured before enabling a Cisc...; Question 284: Refer to the exhibit. (Exhibit) Which result of running the ...; Question 285: A Cisco Nexus 7000 Series switch runs VXLAN, and interface E...; Question 286: (Exhibit) Refer to the exhibit. An engineer configures FCIP ...; Question 287: Refer to the exhibit. (Exhibit) Which backup operation type ...; Question 288: Refer to the exhibit. (Exhibit) Which setting must be config...; Question 289: APIC EPG Resolution Immediacy is set to "Immediate" Which st...; Question 290: An engineer needs to monitor ingress traffic that arrives at...; Question 291: Due to a major version change, an engineer must perform a so...; Question 292: An engineer must use the Embedded Event Manager to monitor e...; Question 293: A DNS server with IP address 192.168.1.1 is deployed in a da...; Question 294: (Exhibit) Refer to the exhibit. An engineer must deploy 70 C...; Question 295: A customer has a requirement to deploy a cloud service and n...; Question 296: Refer to the exhibit. (Exhibit) The STP priority of N7K-1 an...; Question 297: Refer to the exhibit. (Exhibit) Which result of running the ...; Question 298: What is an advantage of using Ansible for automation as comp...; Question 299: Which behavior defines streaming telemetry as a push model i...; Question 300: Multiple roles are applied to a user on the Cisco MDS 9000 S...; Question 301: Refer to the exhibit. (Exhibit) What is a characteristic pre...; Question 302: Refer to the exhibit. (Exhibit) Refer to the exhibit. An eng...; Question 303: An engineer must suggest a deployment model for a newly deve...; Question 304: Refer to the exhibit. (Exhibit) An engineer configures a new...; Question 305: An environment consists of a Cisco MDS 9000 Series Switch th...; Question 306: Which statement is true about upgrading the firmware on a Ci...; Question 307: An engineer needs to monitor ingress traffic that arrives at...; Question 308: A cisco Nexus 9000 series switch experiences a startup confi...; Question 309: Where is the witness deployed in a two-node Cisco HyperFlex ...; Question 310: Drag and drop the storage technologies from the left onto th...; Question 311: An engineer must configure a VXLAN routing on a cisco Nexus ...; Question 312: Refer to the exhibit. (Exhibit) What is the reason the syste...; Question 313: What is a feature of NFS?; Question 314: A company provides applications and database hosting service...; Question 315: Refer to the exhibit. (Exhibit) What is the outcome of this ...; Question 316: Which adjacency server configuration makes two OTV edge devi...; Question 317: AN engineer is asked to modify an overridden policy by chang...; Question 318: An engineer must recover configuration on a Cisco MDS 9000 S...; Question 319: Refer to the exhibit. (Exhibit) An engineer configures a new...; Question 320: An engineer is implementing NPV mode on a Cisco MDS 9000 Ser...; Question 321: Refer to the exhibit. (Exhibit) What is the outcome of this ...; Question 322: (Exhibit) An engineer must use the python module in the gues...; Question 323: Refer to the exhibit. (Exhibit) Refer to the exhibit A netwo...; Question 324: (Exhibit) Refer to the exhibit. VLAN 10 Is experiencing dela...; Question 325: An engineer must configure two Cisco Nexus 7000 series switc...; Question 326: Which product includes prebuilt templates that can be used t...; Question 327: An engineer must implement a Cisco UCS system at a customer ...; Question 328: An engineer is duplicating an existing Cisco UCS setup at a ...; Question 329: Drag and drop the characteristics from the left onto the NAS...; Question 330: (Exhibit) Refer to the exhibit. An engineer must monitor ing...

Question 14/330

LEAVE A REPLY

Download PDF File