<< Prev Question Next Question >>

Question 4/66

An engineer configured two routers connected to two different service providers using BGP with default attributes. One of the links is presenting high delay, which causes slowness in the network. Which BGP attribute must the engineer configure to avoid using the high-delay ISP link if the second ISP link is up?

LEAVE A REPLY

Your email address will not be published. Required fields are marked *

Question List (66q)
Question 1: (Exhibit) Refer to the exhibit. The network administrator co...
Question 2: Which protocol is used to determine the NBMA address on the ...
Question 3: Refer to the exhibit. (Exhibit) The R1 and R2 configurations...
Question 4: An engineer configured two routers connected to two differen...
Question 5: Refer to the following output: Router#show ip nhrp detail 10...
Question 6: Refer to the exhibit. (Exhibit) R1 is connected with R2 via ...
Question 7: Refer to the exhibit. (Exhibit) Which routes from OSPF proce...
Question 8: Refer to the exhibit. (Exhibit) To provide reachability to n...
Question 9: Refer to the exhibit. (Exhibit) An engineer is trying to gen...
Question 10: Refer to the exhibit. (Exhibit) An engineer identifier a Lay...
Question 11: Refer to the exhibits. (Exhibit) When DMVPN is configured, w...
Question 12: (Exhibit) Refer to the exhibit. The network administrator ha...
Question 13: Refer to the exhibit. (Exhibit) A network administrator conf...
Question 14: (Exhibit) Refer to the exhibit. A network administrator redi...
Question 15: A network administrator is tasked to permit http and https t...
Question 16: Which component of MPLS VPNs is used to extend the IP addres...
Question 17: An engineer configured SNMP notifications sent to the manage...
Question 18: An engineer configured a leak-map command to summarize EIGRP...
Question 19: Refer to the exhibit. (Exhibit) During troubleshooting it wa...
Question 20: What are two purposes of using IPv4 and VPNv4 address-family...
Question 21: What are two functions of LDP? (Choose two.)...
2 commentQuestion 22: (Exhibit) Refer to the exhibit. Which action restores the ro...
Question 23: Refer to the exhibit. (Exhibit) A network administrator is u...
Question 24: While working with software images, an engineer observes tha...
Question 25: What does IPv6 Source Guard utilize to determine if IPv6 sou...
Question 26: Refer to the exhibit. (Exhibit) Why is user authentication b...
Question 27: Which SNMP verification command shows the encryption and aut...
Question 28: Refer to the exhibit. (Exhibit) A router receiving BGP routi...
Question 29: Refer to the exhibit. (Exhibit) Which control plane policy l...
Question 30: (Exhibit) Refer to the exhibit. A network administrator conf...
Question 31: An engineer must configure a Cisco router to initiate secure...
Question 32: (Exhibit) Refer to the exhibit. The remote server is failing...
Question 33: Refer to the exhibit. (Exhibit) Which configuration configur...
Question 34: What is a prerequisite for configuring BFD?...
Question 35: Refer to the exhibit. (Exhibit) Which interface configuratio...
Question 36: Which method changes the forwarding decision that a router m...
Question 37: Refer to the exhibit. (Exhibit) An IT staff member comes int...
Question 38: (Exhibit) An engineer sets up a DMVPN connection to connect ...
Question 39: What is a limitation of IPv6 RA Guard?...
Question 40: Which statement about route distinguishers in an MPLS networ...
Question 41: Refer to the exhibit. (Exhibit) An engineer configures a sta...
Question 42: (Exhibit) Refer to the exhibit. The OSPF neighbor relationsh...
Question 43: Which attribute eliminates LFAs that belong to protected pat...
Question 44: Which command allows traffic to load-balance in an MPLS Laye...
Question 45: Refer to the exhibit. (Exhibit) The server for the finance d...
Question 46: Refer to the exhibit. (Exhibit) Users report that IP address...
Question 47: (Exhibit) Refer to the exhibits. An engineer filtered messag...
Question 48: (Exhibit) Refer to the exhibit. An engineer has successfully...
Question 49: Which protocol does MPLS use to support traffic engineering?...
Question 50: Clients on ALS2 receive IPv4 and IPv6 addresses but clients ...
Question 51: Refer to the exhibit. (Exhibit) In which circumstance does t...
Question 52: What is an advantage of using BFD?...
Question 53: Drag and drop the actions from the left into the correct ord...
Question 54: Which statement about MPLS LDP router ID is true?...
Question 55: Drag and drop the packet types from the left onto the correc...
Question 56: Which statement about IPv6 ND inspection is true?...
Question 57: What is a function of IPv6 ND inspection?...
Question 58: What is the role of a route distinguisher via a VRF-Lite set...
Question 59: Refer to the exhibits. (Exhibit) A user on the 192.168.1.0/2...
Question 60: Refer to the exhibit. (Exhibit) An IP SLA was configured on ...
Question 61: Refer to the exhibit. (Exhibit) An engineer is troubleshooti...
Question 62: Which component of MPLS VPNs is used to extend the IP addres...
Question 63: Refer to the exhibit. (Exhibit) Why is the remote NetFlow se...
Question 64: An engineer configured a DHCP server for Cisco IP phones to ...
Question 65: An engineer configured policy-based routing for a destinatio...
Question 66: Which Cisco VPN technology can use multipoint tunnel, result...