<< Prev Question Next Question >>

Question 33/62

By default, how long does a Mobility Services Engine wait for an echo response from a Wireless LAN Controller before declaring the neighbor dead?

LEAVE A REPLY

Your email address will not be published. Required fields are marked *

Question List (62q)
Question 1: What is the default NMSP echo interval between a Mobility Se...
Question 2: An engineer has enabled FlexConnect AP Upgrade for a FlexCon...
Question 3: Which option is a calibration of a Cisco MSE deployment limi...
Question 4: A wireless engineer at a convention center has been asked to...
Question 5: A network engineer is configuring QoS and sees a DSCP value ...
Question 6: Five identical APs at a branch office must be upgraded. You ...
Question 7: A wireless engineer wants to enable optimized roaming for th...
Question 8: A network engineer is experiencing issues enabling LAG on th...
Question 9: A customer is implementing a massively scaled guest wireless...
Question 10: Which network is connected by default when connecting to the...
Question 11: A wireless engineer is configuring a Cisco MSE by using the ...
Question 12: A customer recently implemented WLC wireless multicast. Clie...
Question 13: A network engineer must configure a 5 GHz network to allow f...
Question 14: Branch wireless users report that they can no longer access ...
Question 15: An engineer wants to configure Call Admission Control and en...
Question 16: Which option is a physical entity in converged access wirele...
Question 17: A customer is concerned that the mesh network will not conve...
Question 18: Which two methods to discover a controller does a MAP attemp...
Question 19: A network engineer is viewing the QBSS information in a pack...
Question 20: A network engineer has installed 802.11ac access points with...
Question 21: An engineer must deploy FlexConnect APs to a site that typic...
Question 22: An engineer wants to configure WebEx to adjust the precedenc...
Question 23: After a wireless deployment, users report that wireless voic...
Question 24: A FlexConnect remote office deployment is using five 2702i A...
Question 25: What are two functions of the RAP in a mesh network? (Choose...
Question 26: A customer has implemented a wireless network that requires ...
Question 27: An engineer has installed a new voice WLAN. Which three conf...
Question 28: An engineer has found that voice traffic on the WLAN with ID...
Question 29: A network engineer is debugging issues with the mDNS gateway...
Question 30: When CAPWAP protocol runs over IPv4, which UDP port numbers ...
Question 31: After implementing mDNS gateway, a school's network administ...
Question 32: Which two parameters are used by MSE location analytics to d...
Question 33: By default, how long does a Mobility Services Engine wait fo...
Question 34: A customer wants to restrict the number of SSIDs being offer...
Question 35: A customer has limited staff to manage a wireless network. T...
Question 36: An engineer has deployed a WLAN in a high-density auditorium...
Question 37: An engineer needs to address roaming issues with sticky clie...
Question 38: A network engineer must ensure that corporate wireless users...
Question 39: A client reports that video is not streaming. The administra...
Question 40: Scenario The East-WLC-2504A controller has a problem. When c...
Question 41: What devices can be tracked with the Cisco Context Aware Ser...
Question 42: A wireless printer has been configured with a static IP addr...
Question 43: Controllers WLC_1 and WLC_2 are in the same mobility group. ...
Question 44: How many mDNS profiles can you apply per WLAN?...
Question 45: CMX Facebook WiFi can allow access to the network before aut...
Question 46: A sporting arena has a new wireless network and finds that c...
Question 47: What is the AQ sensitivity when the EDRRM is set to high?...
Question 48: Which IEEE standard allows for the client-AP handshake to be...
Question 49: Clients at a remote FlexConnect site with ID 338789750 are e...
Question 50: A customer has "quiet" wireless clients that use static IP a...
Question 51: DRAG DROP Drag the QoS values from the left and drop them in...
Question 52: You have just added a new MSE to Prime Infrastructure and wa...
Question 53: Which two access categories could use TXOP value higher than...
Question 54: You have set up FlexConnect APs. For which scenario is Fast ...
Question 55: Which feature must be configured on Cisco WLC to prioritize ...
Question 56: A customer requires wireless traffic from the branch to be r...
Question 57: Which three fields are required when creating a new NetFlow ...
Question 58: Clients on access points within an AP group are not receivin...
Question 59: A security engineer wants all guest users to be terminated o...
Question 60: What address do PIM routers listen to in order to automatica...
Question 61: A customer called into the support center with a problem tic...
Question 62: A customer requires that the remote site be able to utilize ...