300-115 Exam Dumps | Which one is related to Stackwise technology?

<< Prev Question Next Question >>

Question 397/446

Which one is related to Stackwise technology?

A. Master switch and backup switch is listed in line.

B. ProStack with mix switch.

C. Multiple switches can be stacked.

D. Switches can be stack with port-channel.

Question List (446q): Question 1: Which authentication service is needed to configure 802.1x?...; Question 2: A physical switch port is part of an EtherChannel group. Wha...; Question 3: A Cisco switch was configured using the "switchport trunk al...; Question 4: Which statement is true about RSTP topology changes?...; Question 5: A network engineer must implement Ethernet links that are ca...; Question 6: Which statement about the use of PagP link aggregation on a ...; Question 7: Which statement about the UDLD protocol is true?...; Question 8: A network engineer tries to configure storm control on an Et...; Question 9: Which two advantages of LLDP are used over CDP? (Choose two....; Question 10: Refer to the exhibit. (Exhibit) The users in an engineering ...; Question 11: Refer to the exhibit. (Exhibit) Which option shows the expec...; Question 12: SERVER SERVER | | S W I T C H ||||||||||| S W I T C H | HOST...; Question 13: What does the command vlan dot1q tag native accomplish when ...; Question 14: Which two restrictions of the port security feature are true...; Question 15: In which portion of the frame is the 802.1q header found?...; Question 16: Which two authentication methods does HSRP use? (Choose two....; Question 17: Which VLAN range is eligible to be pruned when a network eng...; Question 18: When a private VLAN is configured, which mode must be config...; Question 19: Refer to the exhibit. (Exhibit) A multilayer switch has been...; Question 20: Which two possible EtherChannel load balancing mechanisms ar...; Question 21: Which two statements about HSRP timers are true? (Choose two...; Question 22: Which statement is correct about 802.1Q trunking?...; Question 23: Which technique allows specific VLANs to be strictly permitt...; Question 24: The following command was issued on a router that is being c...; Question 25: Which keyword must you use with the storm-control command to...; Question 26: ABC, Inc. is a medium sized company, with an enterprise netw...; Question 27: Where should the Root Guard be implemented in the network to...; Question 28: Which command globally enables AAA on a device?...; Question 29: Refer to the exhibit. (Exhibit) When a network administrator...; Question 30: The network monitoring application alerts a network engineer...; Question 31: Which statement is true about Stackwise?...; Question 32: What is the effect of configuring the following command on a...; Question 33: (Exhibit) Refer to the exhibit. You have applied this config...; Question 34: Which two ISP devices should have trust Port-Statement with ...; Question 35: Which feature places a port in an err-disabled state when it...; Question 36: A network engineer configured an Ethernet switch using these...; Question 37: Which two statements about the HSRP priority are true? (Choo...; Question 38: Refer to exhibit, which two statements correctly indicate wh...; Question 39: Which feature is automatically enabled when a voice VLAN is ...; Question 40: ABC, Inc. is a medium sized company, with an enterprise netw...; Question 41: Which command sets the interval at which a device sends LLDP...; Question 42: Which action allows a network engineer to limit a default VL...; Question 43: Which three advantages of TACACS+ are true? (Choose three.)...; Question 44: Which command is needed to enable DHCP snooping if a switchp...; Question 45: Which two statements about RSPAN VLAN are true? (Choose two....; Question 46: You want to configure a switched internetwork with multiple ...; Question 47: Refer to the exhibit. BPDUGuard is enabled on both ports of ...; Question 48: What two things occur when an RSTP edge port receives a BPDU...; Question 49: Which command correctly configures standby tracking for grou...; Question 50: Which two statements about HSRP are true? (Choose two.)...; Question 51: Which three characteristics of AAA with RADIUS are true? (Ch...; Question 52: Which three authentication methods does GLBP use? (Choose th...; Question 53: While troubleshooting a network outage, a network engineer d...; Question 54: Which two limitations of local SPAN are true? (Choose two.)...; Question 55: What is the size of the VLAN field inside an 802.1q frame?...; Question 56: Which two operational attributes can be checked for EtherCha...; Question 57: When you configure private VLANs on a switch, which port typ...; Question 58: Which SDM template is the most appropriate for a Layer 2 swi...; Question 59: What effect does the mac address-table aging-time 180 comman...; Question 60: What is the process to configure EtherChannel?...; Question 61: In the hardware address 0000.0c07.ac0a, what does 07.ac repr...; Question 62: When you configure a private VLAN, which type of port must y...; Question 63: Which two pieces of information are carried in a Cisco Disco...; Question 64: Which feature must be enabled to eliminate the broadcasting ...; Question 65: What is the link called between a VSS?...; Question 66: Which two statements correctly describe the benefits of GLBP...; Question 67: Refer to the exhibit. (Exhibit) Which EtherChannel negotiati...; Question 68: In which two ways can a port respond to a port-security viol...; Question 69: Which command maximizes system resources for ACLs?...; Question 70: Which two statements about HSRP is true? (Choose two.)...; Question 71: Which statement is true when one of its virtual gateway redu...; Question 72: What is the storm control violation defined by default on a ...; Question 73: Which statements about RSPAN are true? (Choose two.)...; Question 74: Which VTP mode is needed to configure an extended VLAN, when...; Question 75: To provide security, a service provider configures various p...; Question 76: Which three statements are correct with regard to the IEEE 8...; Question 77: Refer to the exhibit. On the basis of the output of the show...; Question 78: Which information in a RADIUS access-request packet is encry...; Question 79: What is the default port security violation?...; Question 80: What statement about MAC address table is true?...; Question 81: Which statement about GLBP is true?...; Question 82: Refer to the exhibit. You can change the SDM template to max...; Question 83: How to configure loop guard in a Cisco switch IOS?...; Question 84: What is the value of the TPID/tag protocol identifier of Qin...; Question 85: Which of the following will cause a switch port to go into t...; Question 86: Refer to the exhibit. Based upon the output of show vlan on ...; Question 87: How do you configure loop guard?...; Question 88: Which option describes a limitation of LLDP?...; Question 89: Which mechanism is specific for RSPAN and not for SPAN?...; Question 90: An enterprise network has port security sticky enabled on al...; Question 91: What is the default amount by which the hot standby priority...; Question 92: Refer to the exhibit. (Exhibit) f1/0 and f1/1 have the same ...; Question 93: Which gateway role is responsible for answering ARP requests...; Question 94: Which VTPv2 mode does the switch operate without participati...; Question 95: Which two secondary VLAN types of Private VLANs (PVLANs)? (C...; Question 96: Instructions Enter IOS commands on the device to verify netw...; Question 97: A manager tells the network engineer to permit only certain ...; Question 98: Refer to the exhibit. (Exhibit) Users of PC-1 experience slo...; Question 99: Which type of packet does DHCP snooping continuously check i...; Question 100: Which command configures an HSRP group to become a slave of ...; Question 101: What VSS technology allows you to share downstream resources...; Question 102: What is the default value for spanning-tree port-priority?...; Question 103: Which two statements are true about recommended practices th...; Question 104: Which statement about using native VLANs to carry untagged f...; Question 105: Refer to the exhibit. An engineer is configuring an ethercha...; Question 106: Which three authentication methods does VRRP use? (Choose th...; Question 107: Which three statements about RSPAN VLAN are true? (Choose th...; Question 108: Pilot testing of the new switching infrastructure finds that...; Question 109: Which statement about the VTPv2 is true?...; Question 110: Which feature actively validates DHCP messages and drops inv...; Question 111: Which Statement about the default SWITCH Database Management...; Question 112: Which three HSRP exchange states are used in multicast messa...; Question 113: Which two commands sequences must you enter on a pair switch...; Question 114: Which information does the subordinate switch in a switch st...; Question 115: How do you configure Spanning-tree EtherChannel guard?...; Question 116: Which statement is true about HSRP?...; Question 117: Which feature rate-limits DHCP traffic?...; Question 118: Refer to the exhibit. (Exhibit) Switch A, B, and C are trunk...; Question 119: What happens if you apply this command "vlan dot1q tag nativ...; Question 120: Where does the VLAN information get saved to?...; Question 121: Which HSRP extension allows groups to share traffic loads?...; Question 122: What is needed for Virtual Switching System "VSS"?...; Question 123: Which two port err-disabled recovery options are used to det...; Question 124: ABC, Inc. is a medium sized company, with an enterprise netw...; Question 125: Refer to the exhibit. Which configuration on the HSRP neighb...; Question 126: What is the benefit of UDLD?; Question 127: Which AAA authorization type applies security policies on a ...; Question 128: Which statement about restrictions for multichassis LACP is ...; Question 129: A network engineer configured a fault-tolerance link on Giga...; Question 130: Which technique will control broadcast, multicast and unicas...; Question 131: Which command is used to configure DHCP snooping for Option ...; Question 132: After UDLD is implemented, a Network Administrator noticed t...; Question 133: What happens when a destination SPAN port that is configured...; Question 134: While working in the core network building, a technician acc...; Question 135: Which feature do you implement so that a physical port will ...; Question 136: Which command would a network engineer apply to error-disabl...; Question 137: Which vtp2 mode does the switch operate without participatin...; Question 138: Refer to the exhibit. You have configured routers R1 and R2 ...; Question 139: During the implementation of a voice solution, which two req...; Question 140: Which two methods are used to configure a trusted option 82?...; Question 141: When using EtherChannel misconfiguration guard, which techno...; Question 142: After the recent upgrade of the switching infrastructure, th...; Question 143: Refer to the exhibit. (Exhibit) A network engineer investiga...; Question 144: Which feature do you implement so that an interface enters t...; Question 145: Which option is the value of the Tag Protocol Identifier 802...; Question 146: Which fallback method can you configure to allow all AAA aut...; Question 147: An engineer is configuring an EtherChannel between two switc...; Question 148: Refer to the exhibit. Switch 15 is configured as the root sw...; Question 149: Which two command sequences must you enter on a pair of swit...; Question 150: If EtherChannel guard is configured, how the interface statu...; Question 151: Which of these options supports to maintain the network arch...; Question 152: Which IOS configuration command is required to configure a V...; Question 153: What do subordinate switches in a switch stack keep?...; Question 154: Which two VLAN ranges can you add, modify or delete on a swi...; Question 155: If all devices on an EtherChannel are sending traffic to a s...; Question 156: An administrator recently configured all ports for rapid tra...; Question 157: Which two statements about 802.1q are true? (Choose two)...; Question 158: What is the maximum number of virtual MAC addresses that GLB...; Question 159: Which option is the minimum frame size of an 802.1Q frame?...; Question 160: Which of the following HSRP router states does an active rou...; Question 161: Select a valid VRRP configuration from a list of possible co...; Question 162: What statement is true if a new switch with a lower bridge I...; Question 163: Which two authentication types does VRRP support? (Choose tw...; Question 164: Refer to the exhibit. (Exhibit) All ports are members of VLA...; Question 165: If VLAN 99 is set to trunk, how can you set it to untagged f...; Question 166: A network is running VTPv2. After verifying all VTP settings...; Question 167: Which option lists the modes that are available for configur...; Question 168: How will the traffic reach the core switch from AS switch to...; Question 169: For security reasons, the IT manager has prohibited users fr...; Question 170: Which VRRP router is responsible for forwarding packets that...; Question 171: Which two statements about errdisable recovery are true? (Ch...; Question 172: Which two statements about MST are true? (Choose two.)...; Question 173: Which two statements about CDP are true? (Choose two.)...; Question 174: Which type of information does the DHCP snooping binding dat...; Question 175: Which statement about the configuration of a trunk port as t...; Question 176: A network engineer must set the load balance method on an ex...; Question 177: Which two statements about the monitored traffic in a SPAN s...; Question 178: What action should a network administrator take to enable VT...; Question 179: Instructions Enter IOS commands on the device to verify netw...; Question 180: Which two statements about an access port with voice VLAN ar...; Question 181: What are the possible results of port-security?...; Question 182: Which command does a network engineer use to verify the span...; Question 183: When IP Source Guard with source IP filtering is enabled on ...; Question 184: HSRP was implemented and configured on two switches while sc...; Question 185: Refer to the exhibit. Which two statements can be derived fr...; Question 186: Which switch feature determines validity based on IP-to-MAC ...; Question 187: Which four mandatory TLVs are valid in CDP? (Choose four.)...; Question 188: A network engineer deployed a switch that operates the LAN b...; Question 189: Which option is the maximum frame size for an 802.1Q frame?...; Question 190: Which three pieces of information about the remote device ar...; Question 191: When a Layer 2 EtherChannel is configured, which statement a...; Question 192: Which two configurations cause the frames to be tagged? (Cho...; Question 193: What will be the behavior of an access port when a tagged pa...; Question 194: Which statement describes what happens when a port configure...; Question 195: An access switch has been configured with an EtherChannel po...; Question 196: Which statement about frame SPAN is true?...; Question 197: Which two statements are true about StackWise? (Choose two.)...; Question 198: Which statement about using EtherChannel on Cisco IOS switch...; Question 199: Which three design types of capable Ethernet LANs does HSRP ...; Question 200: A network engineer is considering implementing UDLD througho...; Question 201: A switch which was connected with 2 fiber cables attached to...; Question 202: What are possible Etherchannel load balancing mechanism base...; Question 203: Which type of MAC address can be dropped by a switch that is...; Question 204: Refer to the exhibit. (Exhibit) Switch A, B, and C are trunk...; Question 205: If a network engineer applies the command mac-address-table ...; Question 206: Which statement about the use of SDM templates in a Cisco sw...; Question 207: Which two statements are true in regards to normal and exten...; Question 208: A network engineer must improve bandwidth and resource utili...; Question 209: Refer to the exhibit. What is the result of setting GLBP wei...; Question 210: On which interface can port security be configured?...; Question 211: Which will identify the master switch in stack wise?...; Question 212: What statements about STP path cost are true? (Choose two.)...; Question 213: Refer to the exhibit. (Exhibit) Which option describes the r...; Question 214: Which two types of threshold can you configure for tracking ...; Question 215: What keyword in macro command is used to configure a root br...; Question 216: Which configuration command ties the router hot standby prio...; Question 217: What are the prerequisite for HSRP interface to come up? (Ch...; Question 218: Refer to the exhibit. Which two commands ensure that DSW1 be...; Question 219: What are three possible router states of HSRP routers on a L...; Question 220: Which STP feature used to monitor BPDU traffic and enable ST...; Question 221: Which statement about Cisco Discovery Protocol configuration...; Question 222: Which two commands can you enter to configure load-balancing...; Question 223: VLAN maps have been configured on switch R1. Which of the fo...; Question 224: Which two TLVs are included in Cisco Discovery Protocol adve...; Question 225: A network engineer is trying to deploy a PC on a network. Th...; Question 226: Behavior of an access port when a tagged packet is received ...; Question 227: Which technique automatically limits VLAN traffic to only th...; Question 228: Which two StackWise configuration setting types are applied ...; Question 229: Which results happens when a non-trunking port that is confi...; Question 230: Which two prerequisites are required for an HSRP interface t...; Question 231: If StormControl is enabled on a port and the traffic reaches...; Question 232: What happens on a Cisco switch that runs Cisco IOS when an R...; Question 233: Which feature describes MAC addresses that are dynamically l...; Question 234: Which two functions of DHCP snooping are true? (Choose two.)...; Question 235: What is the maximum number of 10 Gigabit Ethernet connection...; Question 236: Which two mandatory TLV types does LLDP advertise? (Choose t...; Question 237: Refer to the exhibit. Which two statements can be derived fr...; Question 238: Which switch feature prevents traffic on a LAN from being ov...; Question 239: Which two combinations of Ether Channel modes support the fo...; Question 240: Which statement about RSPAN session is true?...; Question 241: Which SDM template disables routing and supports the maximum...; Question 242: What is the default violation status of port security?...; Question 243: Which of the following are true regarding TACACS+ ? (Choose ...; Question 244: Which two statements about VRRP are true? (Choose two.)...; Question 245: Refer to the exhibit. (Exhibit) Why would the switch be cons...; Question 246: Which two statements apply to LLDP? (Choose two.)...; Question 247: Which of the following commands to configure a DHCP trust is...; Question 248: A network engineer is setting up a new switched network. The...; Question 249: Which three statements are true of a default HSRP configurat...; Question 250: Which hot standby groups numbers are used in a HSRP token ri...; Question 251: Which protocol specified by RFC 2281 provides network redund...; Question 252: What is the command for configuring root guard?...; Question 253: Which extended VLAN range are valid and is stored in the sta...; Question 254: Which database is used to determine the validity of an ARP p...; Question 255: Which two of the following organizationally specific LLDP TL...; Question 256: Which statement is true about dynamic access port?...; Question 257: ABC, Inc. is a medium sized company, with an enterprise netw...; Question 258: Which three values can Cisco IOS device use as the basis for...; Question 259: Refer to the exhibit. If switch SW6 is operating VTP Server ...; Question 260: Refer to the exhibit. (Exhibit) How many bytes are added to ...; Question 261: Which two statements about RPVST+ are true? (Choose two.)...; Question 262: If you have a new switch (that runs spanning-tree mode pvst+...; Question 263: Your manager asked you to make every port on your switch byp...; Question 264: Which two statements about manually-configured LACP EtherCha...; Question 265: Which two requirements are required to form a Layer 2 EtherC...; Question 266: A dynamic access port is member of which VLAN by default?...; Question 267: Which two tasks can be accomplished to configure multiple HS...; Question 268: What happens spoofed packet or something like untrusted pack...; Question 269: 802.1Q trunking, what does it do? (Choose two.)...; Question 270: If HSRP group number is 45 what would be the MAC address? (B...; Question 271: A switch has a pair of fiber and it has been damaged. Which ...; Question 272: Which three statements about SPAN and RSPAN are true? (Choos...; Question 273: Which two statements about GLBP are true? (Choose two.)...; Question 274: Which of the following LLDP mandatory TLVs are valid for bas...; Question 275: Which command is used to verify trunk native VLANs?...; Question 276: Which two device types does DHCP snooping treat as untrusted...; Question 277: Refer to the exhibit. (Exhibit) What is the result of the co...; Question 278: What statement is true about PVST?...; Question 279: What will extend a trust boundary (There is a switch interfa...; Question 280: Which two actions can be configured for storm control violat...; Question 281: Which command enables PortFast and disables port channel on ...; Question 282: Which option is a possible cause for an errdisabled interfac...; Question 283: In a Cisco switch, what is the default period of time after ...; Question 284: Refer to the exhibit. Which two statements about the network...; Question 285: Based on the show spanning-tree vlan 200 output shown in the...; Question 286: Instructions Enter IOS commands on the device to verify netw...; Question 287: In a Virtual Switching System, DSW1 and DSW2 need to communi...; Question 288: Which configuration do you apply to a device to place interf...; Question 289: What is an extension of HSRP that allows load sharing betwee...; Question 290: Which command can you enter to set the time between BPDUs in...; Question 291: How to disable CDP? (Choose two.)...; Question 292: Network engineer wants to use UDLD, what he need to consider...; Question 293: What is the default mode for LACP EtherChannel when configur...; Question 294: Which two options are advantages of deploying VTPv3? (Choose...; Question 295: You want a device to use the local user database if the TACA...; Question 296: Which two statements about PortFast is true? (Choose two.)...; Question 297: Which two restrictions of the port security feature are true...; Question 298: Refer to the exhibit. (Exhibit) The network switches for two...; Question 299: After reviewing UDLD status on switch ports, an engineer not...; Question 300: Which two attributes must match across the member ports, whe...; Question 301: What is the maximum number of VLANs that can be assigned to ...; Question 302: Which two statements about GLBP are true? (Choose two.)...; Question 303: Refer to the exhibit. (Exhibit) Which login credentials are ...; Question 304: When you design a switched network using VTPv2, how many VLA...; Question 305: What is the function of NSF?; Question 306: You administer a network that uses two routers, R1 and R2, c...; Question 307: Which two settings are the parts of a Default LLDP configura...; Question 308: Refer to the exhibit. Based on the debug output, which three...; Question 309: ABC, Inc. is a medium sized company, with an enterprise netw...; Question 310: Which two statements about StackWise are true? (Choose two.)...; Question 311: HSRP has been configured between two Company devices. Which ...; Question 312: When two MST instances (MST 1 and MST 2) are created on a sw...; Question 313: Where can you disable MAC address learning on the switch?...; Question 314: When you enable MST on the switch, what happens?...; Question 315: What is the default interval at which Cisco devices send Cis...; Question 316: Which two statements about SDM templates are true?...; Question 317: Which of these two options are true about RADIUS? (Choose tw...; Question 318: A switch has been configured with the vlan dot1q tag native ...; Question 319: In which two ways are IEEE STP BPDUs forwarded if VLAN 99 is...; Question 320: A network engineer configures port security and 802.1x on th...; Question 321: A network engineer is extending a LAN segment between two ge...; Question 322: What happens if a switch with dhcp snooping and ip source gu...; Question 323: Which private VLAN can have only one VLAN and be a secondary...; Question 324: What happens if we add "line" on AAA command?...; Question 325: EtherChannel guard misconfig is configured on a switch, whic...; Question 326: Which statement is true when UDLD is configured on a link an...; Question 327: Refer to exhibit: How to make DSW1 the primary root for VLAN...; Question 328: Which switchport feature will block the packet with unknown ...; Question 329: Which statement is true about GLBP?...; Question 330: After configuring new data VLANs 1020 through 1030 on the VT...; Question 331: Which three commands are valid to configure DHCP snooping fo...; Question 332: Which three characteristics of AAA with TACACS+ are true? (C...; Question 333: What is cisco recommendation for RSPAN best practice?...; Question 334: Which option is a CISCO recommended RSPAN configuration prac...; Question 335: The network manager has requested that several new VLANs (VL...; Question 336: If switch SW1 is connected in a mesh with four other switche...; Question 337: Given the configuration on a switch interface, what happens ...; Question 338: For which reason does an administrator disable MAC address l...; Question 339: What happens if an interface within channel group is configu...; Question 340: Which options of VLANs IDs are in extended range? (Choose th...; Question 341: Which two statements about VLAN database is true? (Choose tw...; Question 342: Which normal VLAN range are valid and is stored in the vlan....; Question 343: Which statement about the VTP v2 is true?...; Question 344: How to configure DHCP snooping and DAI (Dynamic ARP Inspecti...; Question 345: Refer to the exhibit. Which two statements about the network...; Question 346: Which statement about Cisco devices learning about each othe...; Question 347: A network engineer has just deployed a non-Cisco device in t...; Question 348: Which two commands is used to remove VLAN 55 from the trunk ...; Question 349: Refer to the exhibit. Which two statements about the flag of...; Question 350: Why the network administration can want to disable MAC addre...; Question 351: For client server failover purposes, the application server ...; Question 352: What is the value of the TPID/tag protocol identifier in dot...; Question 353: Which of the following are true regarding TACACS+. ? (Choose...; Question 354: What is true about CDP? (Choose two.)...; Question 355: When a Cisco Catalyst switch that is configured in VTP serve...; Question 356: Which of the following commands are valid to configure DHCP ...; Question 357: An engineer needs to add a customer private VLAN to the netw...; Question 358: Which information is true about RSPAN?...; Question 359: When a switch is added to a stack, which switch automaticall...; Question 360: ABC, Inc. is a medium sized company, with an enterprise netw...; Question 361: Which tool can error-disable an interface if the storm contr...; Question 362: Which private VLAN access port belongs to the primary VLAN a...; Question 363: If HSRP group number is 37, what would be the vMAC (virtual ...; Question 364: When EtherChannel guard is enabled and a misconfiguration is...; Question 365: Refer to the exhibit. (Exhibit) Which statement about switch...; Question 366: Which two protocols can be automatically negotiated between ...; Question 367: What SPAN configuration is required to enable on a switch?...; Question 368: Which two conditions must be met to establish a Layer 2 Ethe...; Question 369: What is the default HSRP priority?...; Question 370: Which two features can you configure on an access port? (Cho...; Question 371: A network engineer must adjust the STP interface attributes ...; Question 372: Which component does the GLBP client cache stores for each h...; Question 373: Which two statements about default FHRP behavior are true? (...; Question 374: Which statement describes what happens when a switch enters ...; Question 375: After you connected a host to switch port G0/1, the port err...; Question 376: Which statement about LLDP-MED is true?...; Question 377: A network engineer changed the port speed and duplex setting...; Question 378: Which describes the default load balancing scheme used by th...; Question 379: Regarding high availability, with the MAC address 0000.0c07....; Question 380: On which PVLAN type can host ports communicate with promiscu...; Question 381: Which three feature sets are used in Stackwise technology? (...; Question 382: Which information does CDP supply from connected devices? (C...; Question 383: Which two statements are true about Option 82? (Choose two.)...; Question 384: Which two statements about VRRP advertisements are true? (Ch...; Question 385: Which option is a benefit of using VSS?...; Question 386: Refer to the exhibit. Currently, R1 is the VRRP master virtu...; Question 387: How to recover err-disable after an UDLD failure?...; Question 388: In a switch stack where is the SDM template stored?...; Question 389: Which two statements about frame LLDP is true?...; Question 390: Which will identify the master switch in stackwise?...; Question 391: Where is SDM template stored in a Stackwise configuration?...; Question 392: Which statement is true about VRRP?...; Question 393: Refer to the exhibit. Which three statements about the netwo...; Question 394: Which two accounting types does AAA support? (Choose two.)...; Question 395: What will be behavior of an access port when a tagged packet...; Question 396: What can happen after a RSPAN configuration in a Cisco switc...; Question 397: Which one is related to Stackwise technology?...; Question 398: Which of the following are valid methods of VRRP authenticat...; Question 399: Which Cisco StackWise feature is supported?...; Question 400: Which statement about HSRP, GLBP, and VRRP is true?...; Question 401: Which two statements about CDP are true? (Choose two.)...; Question 402: Which two statements about Cisco Discovery Protocol are true...; Question 403: How to configure dynamic ARP inspection on a VLAN?...; Question 404: How many Active Virtual Gateways (AVG) can be used in a GLBP...; Question 405: Which three features can be optimized by using SDM templates...; Question 406: While doing network discovery using Cisco Discovery Protocol...; Question 407: Which of the following commands can be issued without interf...; Question 408: Which option lists the information that is contained in a Ci...; Question 409: What is the Ethernet frame size for 802.1Q?...; Question 410: How many VLANs can be assigned to a user access port configu...; Question 411: Where can netflow export data for long term storage and anal...; Question 412: Which statement about the default behavior of a Cisco switch...; Question 413: Which switch is chosen as the stack master during a stack ma...; Question 414: What is required for a LAN switch to support 802.1q Q-in-Q e...; Question 415: Which two statements are true about StackWise? (Choose two.)...; Question 416: (Exhibit) - DSW1 (Distribution Switch 1) is the primary devi...; Question 417: Instructions Enter IOS commands on the device to verify netw...; Question 418: Which protocol will enable a group of routers to form a sing...; Question 419: Which two statements about extended-range VLANs are true? (C...; Question 420: Which configuration do you apply to an interface so that it ...; Question 421: Which two ways can you use to disable Cisco Discovery Protoc...; Question 422: Storm control options apart from the default one. (Choose tw...; Question 423: Which command can be used to block a frame with an unknown d...; Question 424: A new network that consists of several switches has been con...; Question 425: Which two configuration requirements for port security are t...; Question 426: What types of SDM templates you can use in switch? (Choose a...; Question 427: What is the multicast address for HSRPv2?...; Question 428: What is the behavior of an access port when a tagged packet ...; Question 429: What is the default value for the errdisable recovery interv...; Question 430: Which AAA Authorization type includes PPP, SLIP, and ARAP co...; Question 431: Which feature prevents an interface from sending BPDUs on a ...; Question 432: Which three functions does Dynamic ARP Inspection perform wi...; Question 433: Which two new features are included in VTPv3? (Choose two.)...; Question 434: What is the default spanning tree port priority?...; Question 435: Which two differences between RADIUS and TACACS+ are true? (...; Question 436: Which layer private VLAN partition the broadcast domain?...; Question 437: Routers R1 and R2 are configured for HSRP as shown below: Ro...; Question 438: How does VTP pruning enhance network bandwidth?...; Question 439: Under which two conditions does Cisco StackWise Virtual tran...; Question 440: Which six optional TLVs are valid? (Choose six.)...; Question 441: Which First Hop Redundancy Protocol is an IEEE Standard?...; Question 442: Which statement describes what happens if all VSL connection...; Question 443: A workstation technician moves a PC from one office desk to ...; Question 444: Which two prerequisites for HSRP to become active on an inte...; Question 445: With GLBP, in which state is the standby virtual gateway in?...; Question 446: Which command enables root guard on a Cisco switch at locati...

Question 397/446

LEAVE A REPLY

Download PDF File