300-115 Exam Dumps | A network engineer must adjust the STP interface attributes to influence root port selection. Which two

<< Prev Question Next Question >>

Question 31/200

A network engineer must adjust the STP interface attributes to influence root port selection.
Which two elements are used to accomplish this? (Choose two.)

A. root guard

B. cost

C. port-priority

D. link type

E. forward-timers

Question List (200q): Question 1: Which mechanism is specific for RSPAN and not for SPAN?...; Question 2: A network engineer is trying to prevent users from connectin...; Question 3: A network engineer must implement Ethernet links that are ca...; Question 4: Enablement of which feature puts the port into err-disabled ...; Question 5: Which HSRP extension allows groups to share traffic loads?...; Question 6: Refer to the exhibit. (Exhibit) How can the traffic that is ...; Question 7: Which protocol will enable a group of routers to form a sing...; Question 8: You have been asked to install and configure a new switch in...; Question 9: A network engineer is setting up a new switched network. The...; Question 10: What happens if an interface within channel group is configu...; Question 11: Refer to the exhibit. (Exhibit) Users of PC-1 experience slo...; 1 commentQuestion 12: You have been asked to install and configure a new switch in...; Question 13: What are the possible results of port-security?...; Question 14: Which switchport feature will block the packet with unknown ...; Question 15: Which statement about the use of SDM templates in a Cisco sw...; Question 16: After UDLD is implemented, a Network Administrator noticed t...; Question 17: Refer to the exhibit. (Exhibit) Which two statements about t...; Question 18: Which protocol specified by RFC 2281 provides network redund...; Question 19: An engineer is configuring an EtherChannel between two switc...; Question 20: Which two options are two results of using the command spann...; Question 21: Which option is the minimum number of bindings that the DHCP...; Question 22: To follow the Layer 2 switching guidelines, a network engine...; Question 23: What is the default HSRP priority?...; Question 24: Which SDM template is the most appropriate for a Layer 2 swi...; Question 25: Which two command sequences must you enter on a pair of swit...; 3 commentQuestion 26: Which command can be used to block a frame with an unknown d...; Question 27: Which statement about GLBP is true?...; Question 28: A workstation technician moves a PC from one office desk to ...; Question 29: What is the size of the VLAN field inside an 802.1q frame?...; Question 30: A network engineer must improve bandwidth and resource utili...; Question 31: A network engineer must adjust the STP interface attributes ...; Question 32: Which of the following HSRP router states does an active rou...; Question 33: Refer to the exhibit. (Exhibit) What is the result of the co...; Question 34: Refer to the exhibit. (Exhibit) Which option shows the expec...; Question 35: After the implementation of several different types of switc...; Question 36: Which First Hop Redundancy Protocol is an IEEE Standard?...; Question 37: Which database is used to determine the validity of an ARP p...; Question 38: What is the maximum number of VLANs that can be assigned to ...; Question 39: A Cisco Catalyst switch that is prone to reboots continues t...; Question 40: Which two DTP negotiated interface mode combinations negotia...; Question 41: DRAG DROP Drag the appropriate from left to right on descrip...; Question 42: What percentage of bandwidth is reduced when a stack cable i...; Question 43: For which reason does an administrator disable MAC address l...; Question 44: Which component does the GLBP client cache stores for each h...; Question 45: How does VTP pruning enhance network bandwidth?...; Question 46: In which portion of the frame is the 802.1q header found?...; Question 47: Refer to the exhibit. (Exhibit) Which option is the most lik...; Question 48: When two MST instances (MST 1 and MST 2) are created on a sw...; Question 49: After reviewing UDLD status on switch ports, an engineer not...; Question 50: Which statement is correct about 802.1Q trunking?...; Question 51: In regards to Cisco Virtual Switching System which technolog...; Question 52: Which VTP mode is needed to configure an extended VLAN, when...; Question 53: What is the maximum number of virtual MAC addresses that GLB...; Question 54: Which two statements about VRRP are true? (Choose two.)...; Question 55: Which two actions can be configured for storm control violat...; Question 56: CORRECT TEXT You have been tasked with configuring multilaye...; Question 57: Which three features can be optimized by using SDM templates...; Question 58: While doing network discovery using Cisco Discovery Protocol...; Question 59: When SDM templates are configured, which action must be perf...; Question 60: Which command configures an HSRP group to become a slave of ...; Question 61: Which two prerequisites for HSRP to become active on an inte...; Question 62: Which two configurations can you apply to a port so that it ...; Question 63: Your manager asked you to make every port on your switch byp...; Question 64: CORRECT TEXT (Exhibit); Question 65: What is the default interval at which Cisco devices send Cis...; Question 66: Which statement about the MAC address sticky entries in the ...; Question 67: Which two functions of DHCP snooping are true? (Choose two.)...; Question 68: In the hardware address 0000.0c07.ac0a, what does 07.ac repr...; Question 69: DRAG DROP Drag the description from the left to add on appro...; Question 70: Ferris Plastics, Inc. is a medium sized company, with an ent...; Question 71: Which option lists the modes that are available for configur...; Question 72: Refer to the exhibit. (Exhibit) Which two statement can be d...; Question 73: An EtherChannel bundle has been established between a Cisco ...; Question 74: What is the command for configuring root guard?...; Question 75: Refer to the exhibit. (Exhibit) All ports are members of VLA...; Question 76: Which two statements about SPAN source and destination ports...; Question 77: Which VLAN range is eligible to be pruned when a network eng...; Question 78: After configuring new data VLANs 1020 through 1030 on the VT...; Question 79: Which statement is true when one of its virtual gateway redu...; Question 80: When a Layer 2 EtherChannel is configured, which statement a...; Question 81: Refer to the exhibit. (Exhibit) Which login credentials are ...; Question 82: What are three possible router states of HSRP routers on a L...; Question 83: Refer to the exhibit. (Exhibit) Switch A, B, and C are trunk...; Question 84: Which two statements about CDP are true? (Choose two.)...; Question 85: You want to configure a switched internetwork with multiple ...; Question 86: On which interface can port security be configured?...; Question 87: Which layer private VLAN partition the broadcast domain?...; Question 88: Which portion of AAA looks at what a user has access to?...; Question 89: Which technique allows specific VLANs to be strictly permitt...; Question 90: Pilot testing of the new switching infrastructure finds that...; Question 91: Refer to the exhibit. (Exhibit) The network switches for two...; Question 92: DRAG DROP Drag and drop the statements about SPAN source and...; Question 93: Which technique automatically limits VLAN traffic to only th...; Question 94: Refer to the exhibit. (Picture was showing from CLI "show sp...; Question 95: In which two ways are IEEE STP BPDUs forwarded if VLAN 99 is...; Question 96: In a switch stack where is the the SDM template stored?...; Question 97: Which command would a network engineer apply to error-disabl...; Question 98: Which option is a Cisco recommended RSPAN configuration prac...; Question 99: Which private VLAN access port belongs to the primary VLAN a...; Question 100: Which feature is automatically enabled when a voice VLAN is ...; Question 101: Which statements about RSPAN are true? (Choose two.)...; Question 102: A network engineer configures port security and 802.1x on th...; Question 103: Behavior of an access port when a tagged packet is received ...; Question 104: Based on the show spanning-tree vlan 200 output shown in the...; Question 105: Which protocol will enable a group of routers to form a sing...; Question 106: Refer to the exhibit. (Exhibit) The users in an engineering ...; Question 107: DHCP snooping and IP Source Guard have been configured on a ...; Question 108: HSRP has been configured between two Company devices. Which ...; Question 109: After you connected a host to switch port GO/1, the port err...; Question 110: The network manager has requested that several new VLANs (VL...; Question 111: Ferris Plastics, Inc. is a medium sized company, with an ent...; Question 112: Which command globally enables AAA on a device?...; Question 113: What happens if an interface within channel group is configu...; Question 114: Which feature prevents from sending BPDUs on a portfast enab...; Question 115: Which VRRP router is responsible for forwarding packets that...; Question 116: What is the function of NSF?; Question 117: What is the benefit of UDLD?; Question 118: Which two conditions must be met to establish a Layer 2 Ethe...; Question 119: Which statement about Cisco Discovery Protocol configuration...; Question 120: Which switch is chosen as the stack master during a stack ma...; Question 121: What is the default value for the errdisable recovery interv...; Question 122: Refer to the exhibit. (Exhibit) Which EtherChannel negotiati...; Question 123: Which IOS configuration command is required to configure a V...; Question 124: A switch is added into the production network to increase po...; Question 125: DRAG DROP Drag the appropriate terms into specific category....; Question 126: A network engineer wants to add a new switch to an existing ...; Question 127: Routers R1 and R2 are configured for HSRP as shown below: Ro...; Question 128: Which three responses from a RADIUS server are valid? (Choos...; Question 129: Your customer has asked you to come in and verify the operat...; Question 130: Which two statements apply to topology-based switching?...; Question 131: A network engineer is trying to deploy a PC on a network. Th...; Question 132: Your customer has asked you to come in and verify the operat...; Question 133: A server with a statically assigned IP address is attached t...; Question 134: Which three design types of capable Ethernet LANs does HSRP ...; Question 135: What is cisco recommendation for RSPAN best practice?...; Question 136: By default, what is the state of port security on a switch?...; Question 137: What happens if you apply this command "vlan dot1q tag nativ...; Question 138: DRAG DROP Drag and drop the characteristic from the left to ...; Question 139: Which configuration command ties the router hot standby prio...; Question 140: Which two types of threshold can you configure for tracking ...; Question 141: Refer to the exhibit. (Exhibit) Which option describes the r...; Question 142: Which feature do you implement so that an interface enters t...; Question 143: Which file lists all of the configured VLANs on a switch?...; Question 144: In a Cisco switch, what is the default period of time after ...; Question 145: When IP Source Guard with source IP filtering is enabled on ...; Question 146: Refer to the exhibit. (Exhibit) A network engineer wants to ...; Question 147: A new network that consists of several switches has been con...; Question 148: Which switch feature prevents traffic on a LAN from being ov...; Question 149: Which command sequence do you enter to configure an rspan vl...; Question 150: Which of the following commands can be issued without interf...; Question 151: What is the effect of configuring the following command on a...; Question 152: Which option is a possible cause for an errdisabled interfac...; Question 153: After the recent upgrade of the switching infrastructure, th...; Question 154: Which command enables root guard on a Cisco switch at locati...; Question 155: (Exhibit) Refer to the exhibit. Which description of the eff...; Question 156: A switch has been configured with the Vlan dot1q tag native ...; Question 157: Which authentication service is needed to configure 802.1x?...; Question 158: A DHCP configured router is connected directly to a switch t...; Question 159: Refer to the exhibit. (Exhibit) When troubleshooting a netwo...; Question 160: A manager tells the network engineer to permit only certain ...; Question 161: An access switch has been configured with an EtherChannel po...; Question 162: Which feature rate-limits DHCP traffic?...; Question 163: Which two statements about the HSRP priority are true? (Choo...; Question 164: For client server failover purposes, the application server ...; Question 165: An administrator recently configured all ports for rapid tra...; Question 166: Which two statements about manually-configured LACP EtherCha...; Question 167: switch#show standby Virtual IP address is X.X.X.X Hello time...; Question 168: Which three statements are true of a default HSRP configurat...; Question 169: What is required for a LAN switch to support 802.1q Q-in-Q e...; Question 170: Refer to the exhibit. (Exhibit) You have configured routers ...; Question 171: A network engineer configured a fault-tolerance link on Giga...; Question 172: The behavior of VLAN 1 BPDUs in a situation where the Native...; Question 173: Interfaces are assigned to a VLAN, and then the VLAN is dele...; Question 174: When a Cisco Catalyst switch that is configured in VTP serve...; Question 175: When using EtherChannel misconfiguration guard, which techno...; Question 176: The command storm-control broadcast level 75 65 is configure...; Question 177: In which two ways can a port respond to a port-security viol...; Question 178: Refer to the exhibit. (Exhibit) How many bytes are added to ...; Question 179: Which statement describes what happens if all VSL connection...; Question 180: When you design a switched network using VTPv2, how many VLA...; Question 181: Ferris Plastics, Inc. is a medium sized company, with an ent...; Question 182: When Ether Channel guard is enabled and a misconfiguration i...; Question 183: Which option is a benefit of using VSS?...; Question 184: Which two statements about HSRP, GLBP, and VRRP are true? (C...; Question 185: On which layer does IP source guard provide filtering to pre...; Question 186: Which feature do you implement so that a physical port enter...; Question 187: Which feature places a port in an err-disabled state when it...; Question 188: CORRECT TEXT Scenario: You work for SWITCH.com. They have ju...; Question 189: Which two statements about extended-range VLANs are true? (C...; Question 190: Which two combinations of Ether Channel modes support the fo...; Question 191: For security reasons, the IT manager has prohibited users fr...; Question 192: Refer to the output below. (Exhibit) Which two effects of th...; Question 193: Which two operational attributes can be checked for EtherCha...; Question 194: Where can NetFlow export data for long term storage and anal...; Question 195: Which command does a network engineer use to verify the span...; Question 196: In regards to Cisco Virtual Switching System, which technolo...; Question 197: Which AAA Authorization type includes PPP, SLIP, and ARAP co...; Question 198: Which statement is true about RSTP topology changes?...; Question 199: Refer to the exhibit. (Exhibit) You change a switch SDM temp...; Question 200: Refer to the exhibit. (Exhibit) Which two statements about S...

Question 31/200

LEAVE A REPLY

Download PDF File