200-125 Exam Dumps | (Exhibit) Refer to the exhibit. All switch ports are assigned to the correct VLANs, but none of the hosts

Valid 200-125 Dumps shared by ExamDiscuss.com for Helping Passing 200-125 Exam! ExamDiscuss.com now offer the newest 200-125 exam dumps, the ExamDiscuss.com 200-125 exam questions have been updated and answers have been corrected get the newest ExamDiscuss.com 200-125 dumps with Test Engine here:

Access 200-125 Dumps Premium Version
(754 Q&As Dumps, 35%OFF Special Discount Code: freecram)

<< Prev Question Next Question >>

Question 484/604

Refer to the exhibit. All switch ports are assigned to the correct VLANs, but none of the hosts connected to SwitchA can communicate with hosts in the same VLAN connected to SwitchB. Based on the output shown, what is the most likely problem?

A. The link between the switches is configured in the wrong VLAN.

B. The link between the switches needs to be configured as a trunk.

C. VTP is not configured to carry VLAN information between the switches.

D. The access link needs to be configured in multiple VLANs.

E. Switch IP addresses must be configured in order for traffic to be forwarded between the switches

Question List (604q): Question 1: Which type of access list compares source and destination IP...; Question 2: Refer to the exhibit. A network administrator is configuring...; Question 3: Which three are characteristics of an IPv6 anycast address? ...; Question 4: Which configuration command can you apply to a HSRP router s...; Question 5: Refer to the exhibit, The VLAN configuration of S1 is not be...; Question 6: Which two commands correctly verify whether port security ha...; Question 7: How is provided master redundancy on a stacked switches?...; Question 8: Which standards-based First Hop Redundancy Protocol is a Cis...; Question 9: Refer to the exhibit. Given this output for SwitchC, what sh...; Question 10: Refer to the exhibit. How should the FastEthernet0/1 port on...; Question 11: Which NAT type is used to translate a single inside address ...; Question 12: Refer to the exhibit. Which address range efficiently summar...; Question 13: Instructions Enter IOS commands on the device to verify netw...; Question 14: Which three functions are major components of a network virt...; Question 15: Which command enables RSTP on a switch?...; Question 16: Which three elements are field in a basic Ethernet data fram...; Question 17: Refer to Exhibit. How many broadcast domains are shown in th...; Question 18: Which two types of NAT addresses are used in a Cisco NAT dev...; Question 19: Which option is the default switch port port-security violat...; Question 20: Refer to the exhibit. Refer to the exhibit. After HostA ping...; Question 21: What is the first step in the NAT configuration process?...; Question 22: How to verify SSH connections was secured?...; Question 23: Refer to the exhibit. A network technician is asked to desig...; Question 24: Which three statements accurately describe layer 2 Ethernet ...; Question 25: Which three statements about static routing are true? (Choos...; Question 26: Which option is the industry-standard protocol for EtherChan...; Question 27: Scenario Refer to the topology. Your company has decided to ...; Question 28: Which statement describes VRRP object tracking?...; Question 29: Which two statements about IPv6 router advertisement message...; Question 30: What are two advantages of Layer 2 Ethernet switches over hu...; Question 31: Which NTP command configures the local device as an NTP refe...; Question 32: When a router makes a routing decision for a packet that is ...; Question 33: Which process is associated with spanning-tree convergence?...; Question 34: Which two advantages do dynamic routing protocols provide ov...; Question 35: Which command allows you to verify the encapsulation type (C...; Question 36: Which two benefits are provided by creating VLANs? (Choose t...; Question 37: Which two link protocols are used to carry multiple VLANs ov...; Question 38: Which two are advantages of static routing when compared to ...; Question 39: Switch ports operating in which two roles will forward traff...; Question 40: If host Z needs to send data through router R1 to a storage ...; Question 41: Which command is used to enable CHAP authentication, with PA...; Question 42: Which item represents the standard IP ACL?...; Question 43: Refer to the exhibit. The access list has been configured on...; Question 44: Which name describes an IPV6 host-enable tunneling technique...; Question 45: What is the result of issuing the frame-relay map ip 192.168...; Question 46: For which routes does the distance bgp 10 50 70 command set ...; Question 47: In order to comply with new auditing standards, a security a...; Question 48: Which two EtherChannel PAgP modes can you configure? (Choose...; Question 49: The access control list shown in the graphic has been applie...; Question 50: Which three commands are required to enable NTP authenticati...; Question 51: Refer to the exhibit. In the Frame Relay network, which IP a...; Question 52: When you enable PortFast on a switch port, the port immediat...; Question 53: When you troubleshoot an IPv4 connectivity issue on a router...; Question 54: What are two enhancements that OSPFv3 supports over OSPFv2? ...; Question 55: Which command can you enter in global configuration mode to ...; Question 56: What is the status of port-channel if LACP is misconfigured?...; Question 57: Which statement about static routes is true?...; Question 58: Refer to the exhibit. Which two statements are true based th...; Question 59: The enable secret command is used to secure access to which ...; Question 60: What are the three major components of cisco network virtual...; Question 61: What command is used to verify the DLCI destination address ...; Question 62: Which keyword enables an HSRP router to take the active role...; Question 63: Instructions Enter IOS commands on the device to verify netw...; Question 64: Which two statements about EUI-64 addressing are true? (Choo...; Question 65: Which two authentic methods are compatible with MLPPP on a s...; Question 66: Which command encrypts all plaintext passwords?...; Question 67: Refer to the exhibit. (Exhibit) What is the effect of the gi...; Question 68: Instructions Enter IOS commands on the device to verify netw...; Question 69: After you configure the ip dns spoofing command globally on ...; Question 70: Which symptom most commonly indicates that two connecting in...; Question 71: Which type does a port become when it receives the best BPDU...; Question 72: Scenario (Exhibit) An administrator is trying to ping and te...; Question 73: It has become necessary to configure an existing serial inte...; Question 74: Which three technical services support cloud computing? (Cho...; Question 75: (Exhibit) Refer to the exhibit. After you apply the given co...; Question 76: Which two statements about LLDP are true? (Choose two.)...; Question 77: Refer to the exhibit. What is the meaning of the term dynami...; Question 78: (Exhibit) Refer to the exhibit. R1 is unable to establish an...; Question 79: Refer to the exhibit. The network shown in the diagram is ex...; Question 80: When a DHCP server is configured, which two IP addresses sho...; Question 81: VLAN 3 is not yet configured on your switch. What happens if...; Question 82: What is new in HSRPv2?; Question 83: Refer to the exhibit. While troubleshooting a switch, you ex...; Question 84: Which condition indicates that service password-encryption i...; Question 85: Which command can you enter to display the operational statu...; Question 86: What can you change to select switch as root bridge?...; Question 87: Which statement about slow inter VLAN forwarding is true?...; Question 88: Refer to the exhibit. Which three statements are true about ...; Question 89: How are VTP advertisements delivered to switches across the ...; Question 90: Which feature is configured by setting a variance that is at...; Question 91: Refer to the exhibit. A technician is troubleshooting host c...; Question 92: Which port security violation mode allows traffic from valid...; Question 93: Which two options are benefits of DHCP snooping? (Choose two...; Question 94: Which statement about Cisco Discovery Protocol is true?...; Question 95: Refer to the exhibit. What is the result of setting the no l...; Question 96: The network administrator is asked to configure 113 point-to...; Question 97: Refer to the exhibit. Which rule does the DHCP server use wh...; Question 98: Where does the configuration reside when a helper address is...; Question 99: Refer to the exhibit. Given the output shown from this Cisco...; Question 100: Which command can you enter to set the default route for all...; Question 101: Which two options are valid numbers for a standard access li...; Question 102: Instructions: - Enter IOS commands on the device to verify n...; Question 103: What to do when the router password was forgotten?...; Question 104: Refer to the exhibit. This command is executed on 2960Switch...; Question 105: Which three options are types of IPv6 static routes? (Choose...; Question 106: How to see dhcp conflict?; Question 107: Refer to the exhibit. What two results would occur if the hu...; Question 108: When troubleshooting client DNS issues, which two tasks must...; Question 109: Which technology supports the stateless assignment of IPv6 a...; Question 110: (Exhibit) What destination Layer 2 address will be used in t...; Question 111: Which configuration can you apply to enable encapsulation on...; Question 112: Which two protocols are used by bridges and/or switches to p...; Question 113: Instructions This item contains several questions that you m...; Question 114: Which statement about Cisco Discovery Protocol is true?...; Question 115: What are the requirement to configure DHCP binding? (Choose ...; Question 116: Which type of interface can negotiate an IP address for a PP...; Question 117: (Exhibit) If required, what password should be on the router...; Question 118: Which three options are benefits of using TACACS+ on a devic...; Question 119: Which two types of information are held in the MAC address t...; Question 120: Which command you enter on a switch to display the ip addres...; Question 121: As a CCNA candidate, you must have a firm understanding of t...; Question 122: If primary and secondary root switches with priority 16384 b...; Question 123: Which value must the device send as its username when using ...; Question 124: Where does a switch maintain DHCP snooping information?...; Question 125: How to create a trunk port and allow VLAN 20? (Choose three....; Question 126: Scenario Refer to the topology. Your company has decided to ...; Question 127: Which two statements correctly describe steps in the OSI dat...; Question 128: Refer to the exhibit. A network associate needs to configure...; Question 129: What are contained in layer 2 Ethernet frame? (Choose three....; Question 130: What are three broadband wireless technologies? (Choose thre...; Question 131: Refer to the exhibit. What statement is true of the configur...; Question 132: Assuming the default switch configuration, which VLAN range ...; Question 133: While troubleshooting a GRE tunnel interface issue, show int...; Question 134: Instructions This item contains several questions that you m...; Question 135: What is a valid HSRP virtual MAC address?...; Question 136: Which two statements about data VLANs on access ports are tr...; Question 137: Which of the following describes the roles of devices in a W...; Question 138: Two routers named Atlanta and Brevard are connected via thei...; Question 139: Refer to the exhibit A frame on vlan 1on switch s1 is sent t...; Question 140: Which command sets and automatically encrypts the privileged...; Question 141: Refer to the exhibit. A network administrator attempts to pi...; Question 142: What are two benefits of using NAT? (Choose two.)...; Question 143: Refer to the exhibit. Switch port FastEthernet 0/24 on ALSwi...; Question 144: What is the effect of using the service password-encryption ...; Question 145: Which function does traffic shaping perform?...; Question 146: A national retail chain needs to design an IP addressing sch...; Question 147: Which identification number is valid for an extended ACL?...; Question 148: What are two security appliances that can be installed in a ...; Question 149: Which two statements about using the CHAP authentication mec...; Question 150: Which two statements about IPv6 address 2002:ab10:beef::/48 ...; Question 151: Which protocol is an open standard protocol framework that i...; Question 152: Which three statements about RSTP are true? (choose three)...; Question 153: Under which circumstance is a router on a stick most appropr...; Question 154: By default, how many MAC addresses are permitted to be learn...; Question 155: (Exhibit) Refer to the exhibit. Assuming that the entire net...; Question 156: What are two benefits of using VTP in a switching environmen...; Question 157: Which method does a connected trunk port use to tag VLAN tra...; Question 158: (Exhibit) Which connection uses the default encapsulation fo...; Question 159: Which routing protocol use first-hand information?...; Question 160: Which command can you enter to configure an IPV6 floating st...; Question 161: Which command is used to configure a switch as an authoritat...; Question 162: Which statement about unicast frame forwarding on a switch i...; Question 163: Refer to the exhibit. A frame on VLAN 1 on switch S1 is sent...; Question 164: If all switches are configured with default values, which sw...; Question 165: Which utility can you use to identify redundant or shadow ru...; Question 166: Scenario Refer to the topology. Your company has decided to ...; Question 167: For which two reasons might be you choose chassis aggregatio...; Question 168: Which command can you enter to troubleshoot the failure of a...; Question 169: Which feature builds a FIB and an adjacency table to expedit...; Question 170: Which of the port is not part of STP protocol?...; Question 171: Which command can you enter to verify that a router is synce...; Question 172: Which VTP mode prevents you from making changes to VLANs?...; Question 173: How can you disable DTP on a switch port?...; Question 174: Which statement about VLAN operation on Cisco Catalyst switc...; Question 175: When you deploy multilink PPP on your network, where must yo...; Question 176: What occurs on a Frame Relay network when the CIR is exceede...; Question 177: Which switch would STP choose to become the root bridge in t...; Question 178: A router has learned three possible routes that could be use...; Question 179: Scenario Refer to the topology. Your company has decided to ...; Question 180: When a device learns multiple routes to a specific network, ...; Question 181: Which two characteristics are representative of a link-state...; Question 182: Which of the following privilege level is the most secured?...; Question 183: A network administrator creates a layer 3 EtherChannel, bund...; Question 184: Which of these represents an IPv6 link-local address?...; Question 185: Which RPVST+ port state is excluded from all STP operations?...; Question 186: Which type of access list compares source and destination IP...; Question 187: What is the difference between a CSU/DSU and a modem?...; Question 188: Which of the following IP addresses fall into the CIDR block...; Question 189: A network administrator is configuring ACLs on a Cisco route...; Question 190: Refer to the exhibit. The networks connected to router R2 ha...; Question 191: Which value can you modify to configure a specific interface...; Question 192: Which part of the PPPoE server configuration contains the in...; Question 193: Which of the following is needed to be enable back the role ...; Question 194: Which two statements about IPv6 multicast addresses are true...; Question 195: Which two differences between distance-vector and link-state...; Question 196: In which three ways is an IPv6 header simpler than an IPv4 h...; Question 197: Which value to use in HSRP protocol election process?...; Question 198: Which statement about switch access ports is true?...; Question 199: Which command can you enter to display the hits counter for ...; Question 200: As a network administrator, you have been instructed to prev...; Question 201: Instructions Enter IOS commands on the device to verify netw...; Question 202: The following access list below was applied outbound on the ...; Question 203: Which feature must you enable to distribute vlans automatica...; Question 204: What field is consisted of 6 bytes in the field identificati...; Question 205: Which three statements are correct about RIP version 2? (Cho...; Question 206: Which three statements about link-state routing are true? (C...; Question 207: Which address is the IPv6 all-RIP-routers multicast group ad...; Question 208: Users have been complaining that their Frame Relay connectio...; Question 209: Refer to the exhibit. Based on the information given, which ...; Question 210: Which command sequence can you enter to create VLAN 20 and a...; Question 211: For what two purposes does the Ethernet protocol use physica...; Question 212: Which three options are the HSRP states for a router? (Choos...; Question 213: What is the effect of the overload keyword in a static NAT t...; Question 214: Which major component of the Cisco network virtualization ar...; Question 215: Which two values are used by Spanning Tree Protocol to elect...; Question 216: A network administrator needs to configure a serial link bet...; Question 217: If you want multiple hosts on a network, where do you config...; Question 218: Which path does a router choose when it receives a packet wi...; Question 219: Which two benefits are provided by using a hierarchical addr...; Question 220: Which subnet mask would be appropriate for a network address...; Question 221: If all OSPF routers in a single area are configured with the...; Question 222: Refer to the exhibit. Statements A, B, C, and D of ACL 10 ha...; Question 223: Which statement about EIGRP on IPv6 devices is true?...; Question 224: The OSPF Hello protocol performs which of the following task...; Question 225: What is the best way to verify that a host has a path to oth...; Question 226: What can be done to secure the virtual terminal interfaces o...; Question 227: Which password types are encrypted?...; Question 228: You enter the show ipv6 route command on an OSPF device and ...; Question 229: Refer to the exhibit. What is the most efficient summarizati...; Question 230: Which option is the benefit of implementing an intelligent D...; Question 231: Assuming the default switch configuration which vlan range c...; Question 232: Which type of address is the public IP address of a NAT devi...; Question 233: Which type of routing protocol operates by using first infor...; Question 234: Which spanning-tree feature places a port immediately into a...; Question 235: What are two characteristics of Frame Relay point-to-point s...; Question 236: Which two statements about switch stacking are true? (Choose...; Question 237: (Exhibit) A static map to the S-AMER location is required. W...; Question 238: Which three statements about HSRP operation are true? (Choos...; Question 239: On a network of one department, there are four PCs connected...; Question 240: How does using the service password-encryption command on a ...; Question 241: Instructions: - Enter IOS commands on the device to verify n...; Question 242: How many bits are contained in each field of an IPv6 address...; Question 243: Which statement about MPLS is true?...; Question 244: Refer to the exhibit. At the end of an RSTP election process...; Question 245: Which two options are primary responsibilities of the APIC-E...; Question 246: What will be the result if the following configuration comma...; Question 247: Which type of broadcast barely used in IPv4 which also exist...; Question 248: Refer to the exhibit. A network technician is unable to ping...; Question 249: Which benefit of implementing a dual-homed WAN connection in...; Question 250: Which two types of information are held in the mac address t...; Question 251: On which combinations are standard access lists based?...; Question 252: Refer to the exhibit. Switch-1 needs to send data to a host ...; Question 253: You have configured a router with an OSPF router ID, but its...; Question 254: On which type of device is every port in the same collision ...; Question 255: Which DTP switch port mode allows the port to create a trunk...; Question 256: Which of the following are benefits of VLANs? (Choose three....; Question 257: A network interface port has collision detection and carrier...; Question 258: Which value is indicated by the next hop in a routing table?...; Question 259: A BPDU guard is configured on an interface that has PortFast...; Question 260: Which command can you enter to verify that a 128-bit address...; Question 261: Which destination IP address can a host use to send one mess...; Question 262: Refer to the exhibit. (Exhibit) What is the effect of the gi...; Question 263: Refer to the exhibit. Given this output for SwitchC, what sh...; Question 264: What parameter can be different on ports within an EtherChan...; Question 265: Refer to the exhibit. In this VLSM addressing scheme, what s...; Question 266: Which statement about recovering a password on a Cisco route...; Question 267: Which command can you enter to re-enable Cisco Discovery Pro...; Question 268: Which command is used to build DHCP pool?...; Question 269: interface fa0/0 ip address x.x.x.33 255.255.255.224 router b...; Question 270: A network administrator is planning a network installation f...; Question 271: Which three commands must you enter to create a trunk that a...; Question 272: Standard industrialized protocol of EtherChannel?...; Question 273: Which three circumstances can cause a GRE tunnel to be in an...; Question 274: Which WAN topology is most appropriate for a centrally locat...; Question 275: Which two pieces of information can be shared with LLDP TLVs...; Question 276: While you were troubleshooting a connection issue, a ping fr...; Question 277: Which two values are needed to run the APIC-EM ACL Analysis ...; Question 278: Refer to the exhibit. Which three statements correctly descr...; Question 279: How to configure RIPv2? (Choose two.)...; Question 280: In a GLBP network, who is responsible for the arp request?...; Question 281: A network administrator needs to allow only one Telnet conne...; Question 282: Refer to the exhibit. HostA cannot ping HostB. Assuming rout...; Question 283: Which two options describe benefits of aggregated chassis te...; Question 284: Cisco Catalyst switches CAT1 and CAT2 have a connection betw...; Question 285: Which type of routing protocol operates by exchanging the en...; Question 286: An access list was written with the four statements shown in...; Question 287: Which technology you will choose to connect multiple sites w...; Question 288: Which three elements must be used when you configure a route...; Question 289: Which technology can enable multiple VLANs to communicate wi...; Question 290: Refer to the diagram. All hosts have connectivity with one a...; Question 291: Under which two circumstances is a switch port that is confi...; Question 292: Which two statements about using leased lines for your WAN i...; Question 293: Refer to the exhibit. You have discovered that computers on ...; Question 294: Which option is the primary purpose of traffic shaping?...; Question 295: Which statement about ACLs is true?...; Question 296: Which type of attack can be mitigated by configuring the def...; Question 297: Which statement is correct regarding the operation of DHCP?...; Question 298: The network administrator of the Oregon router adds the foll...; Question 299: Which are valid modes for a switch port used as a VLAN trunk...; Question 300: Which NTP type designates a router without an external refer...; Question 301: Which statement about the inside interface configuration in ...; Question 302: Which task must you perform to enable an IOS device to use D...; Question 303: Which two benefits can you get by stacking Cisco switches? (...; Question 304: Instructions This item contains several questions that you m...; Question 305: Which dynamic routing protocol uses only the hop count to de...; Question 306: Refer to the exhibit. (Exhibit) Switch port FastEthernet 0/2...; Question 307: What is the purpose of Inverse ARP?...; Question 308: Refer to the exhibit. How should the FastEthernet0/1 ports o...; Question 309: Which two statements about TACACS+ are true? (Choose two.)...; Question 310: Which technology allows a large number of private IP address...; Question 311: Which two of these are characteristics of the 802.1Q protoco...; Question 312: This graphic shows the results of an attempt to open a Telne...; Question 313: Refer to the exhibit. Which statement is true? (Exhibit)...; Question 314: The network administrator has been asked to give reasons for...; Question 315: (Exhibit) Refer to the exhibit. Which switch provides the sp...; Question 316: (Exhibit) Refer to the exhibit. If the devices produced the ...; Question 317: Which device allows users to connect to the network using a ...; Question 318: What is a possible reason why a host is able to ping a web s...; Question 319: Which option is the master redundancy scheme for stacked swi...; Question 320: Refer to the exhibit. Host A pings interface S0/0 on router ...; Question 321: Refer to the exhibit. A junior network administrator was giv...; Question 322: Refer to exhibit. What Administrative distance has route to ...; Question 323: Which protocol is the Cisco proprietary implementation of FH...; Question 324: Which function enables an administrator to route multiple VL...; Question 325: The command frame-relay map ip 10.121.16.8 102 broadcast was...; Question 326: Refer to the exhibit. The output that is shown is generated ...; Question 327: On which type of port can switches interconnect for multi-VL...; Question 328: Which IEEE standard protocol is initiated as a result of suc...; Question 329: A network administrator receives an error message while tryi...; Question 330: Which command can you enter to display duplicate IP addresse...; Question 331: On which combinations are standard access lists based?...; Question 332: Which two states are the port states when RSTP has converged...; Question 333: What is a difference between TACACS+ and RADIUS in AAA?...; Question 334: What are three characteristics of satellite Internet connect...; Question 335: Which three options are types of Layer 2 network attacks? (C...; Question 336: Which standards-based First Hop Redundancy Protocol is a Cis...; Question 337: What should be part of a comprehensive network security plan...; Question 338: A network engineer wants to allow a temporary entry for a re...; Question 339: How does a DHCP server dynamically assign IP addresses to ho...; Question 340: Which additional configuration step is necessary in order to...; Question 341: Which spanning-tree protocol rides on top of another spannin...; Question 342: Refer to the exhibit. What will Router1 do when it receives ...; Question 343: Which statement about DTP is true?...; Question 344: Which two options are requirements for configuring RIPv2 on ...; Question 345: Which Layer 2 protocol encapsulation type supports synchrono...; Question 346: What are two advantages of static routing? (Choose two.)...; Question 347: Refer to the topology below and answer the following questio...; Question 348: Which type of MAC address is aged automatically by the switc...; Question 349: Router R1 has a static route that is configured to a destina...; Question 350: Which two statements are true about the command ip route 172...; Question 351: During which phase of PPPoE is PPP authentication performed?...; Question 352: Which two commands can be used to verify a trunk link config...; Question 353: A network administrator is troubleshooting the OSPF configur...; Question 354: Configuration of which option is required on a Cisco switch ...; Question 355: What are two reasons that duplex mismatches can be difficult...; Question 356: Refer to the topology below and answer the following questio...; Question 357: Which set of commands is recommended to prevent the use of a...; Question 358: In an Ethernet network, under what two scenarios can devices...; Question 359: Which command can you use to manually assign a static IPv6 a...; Question 360: Refer to the exhibit. The two exhibited devices are the only...; Question 361: Which statement about named ACLs is true?...; Question 362: Which feature can you implement to reserve bandwidth for VoI...; Question 363: Which type of secure MAC address must be configured manually...; Question 364: Which value must a device send as its username when using CH...; Question 365: Which statement about routing protocols is true?...; Question 366: Refer to the exhibit. At the end of an RSTP election process...; Question 367: Which three statements about Syslog utilization are true? (C...; Question 368: OSPF enable on interface with multiple ipv6 prefix which ip ...; Question 369: How does NAT overloading provide one-to-many address transla...; Question 370: Assuming a subnet mask of 255.255.248.0, three of the follow...; Question 371: Which type of cable must you use to connect to device with m...; Question 372: Which two of these statements regarding RSTP are correct? (C...; Question 373: Which command can you enter to route all traffic that is des...; Question 374: What are the two minimum required components of a DHCP bindi...; Question 375: Which two statements about stateful firewalls in an enterpri...; Question 376: Which IEEE standard does PVST+ use to tunnel information?...; Question 377: An administrator is unsuccessful in adding VLAN 50 to a swit...; Question 378: Which address prefix does OSPFv3 use when multiple IPv6 addr...; Question 379: Which three options are switch port config that can always a...; Question 380: Which two benefits of implementing a full-mesh WAN topology ...; Question 381: What are two requirements for an HSRP group? (Choose two)...; Question 382: In which situation would the use of a static route be approp...; Question 383: What are three benefits of GLBP? (Choose three.)...; Question 384: Three switches are connected to one another via trunk ports....; Question 385: Refer to the exhibit. Both switches are using a default conf...; Question 386: The Frame Relay network in the diagram is not functioning pr...; Question 387: What is the two benefits of DHCP snooping? (Choose two.)...; Question 388: Where information about untrusted hosts are stored?...; Question 389: Which three statements about VTP features are true? (Choose ...; Question 390: Why will a switch never learn a broadcast address?...; Question 391: How should a router that is being used in a Frame Relay netw...; Question 392: How is an EUI-64 format interface ID created from a 48-bit M...; Question 393: Which IPV6 function serves the same purpose as ARP entry ver...; Question 394: What is one benefit of PVST+?; Question 395: Which utility can you use to identify the cause of a traffic...; Question 396: Which NAT function can map multiple inside addresses to a si...; Question 397: If the primary root bridge experiences a power loss, which s...; Question 398: Which PPP subprotocol negotiates authentication options?...; Question 399: Which prompt does a Cisco switch display when it is running ...; Question 400: In a switched environment, what does the IEEE 802.1Q standar...; Question 401: VLAN 3 is not yet configured on your switch. What happens if...; Question 402: A company is installing IP phones. The phones and office com...; Question 403: Which two statements about firewalls are true? (Choose two.)...; Question 404: Which mode are in PAgP? (Choose two.)...; Question 405: When enabled, which feature prevents routing protocols from ...; Question 406: Which two authentication methods are compatible with MLPPP o...; Question 407: A router has two Fast Ethernet interfaces and needs to conne...; Question 408: Refer to exhibit. A network administrator cannot establish a...; Question 409: Refer to the exhibit. Router edge-1 is unable to establish O...; Question 410: What value is primarily used to determine which port becomes...; Question 411: A network administrator is explaining VTP configuration to a...; Question 412: Which command can you enter to create a NAT pool of 6 addres...; Question 413: Which two switch states are valid for 802.1w? (Choose two.)...; Question 414: Which of the following services use UDP? (Choose three.)...; Question 415: Refer to the exhibit. Users on the 172.17.22.0 network canno...; Question 416: Which statement about access lists that are applied to an in...; Question 417: While troubleshooting a DCHP client that is behaving erratic...; Question 418: Which three statements about DTP are true? (Choose three.)...; Question 419: What is one requirement for interfaces to run IPv6?...; Question 420: Which two of these statements are true of IPv6 address repre...; Question 421: How to enable vlans automatically across multiple switches?...; Question 422: Which command can you enter in a network switch configuratio...; Question 423: Which of the following are key characteristics of PPP? (Choo...; Question 424: Which value is used to determine the active router in an HSR...; Question 425: The output of the show frame-relay pvc command shows "PVC ST...; Question 426: Which two statements about VTP are true? (Choose two.)...; Question 427: Host 1 is trying to communicate with Host 2. The e0 interfac...; Question 428: Which NTP command configures the local devices as an NTP ref...; Question 429: Refer to the exhibit. (Exhibit) Each of these four switches ...; Question 430: Which command can you enter to determine the addresses that ...; Question 431: Which Layer 2 protocol encapsulation type supports synchrono...; Question 432: What is the danger of the permit any entry in a NAT access l...; Question 433: Which MTU size can cause a baby giant error?...; Question 434: Which statement about spanning-tree root-bridge election is ...; Question 435: A network administrator wants to add a line to an access lis...; Question 436: Instructions: - Enter IOS commands on the device to verify n...; Question 437: Which term describes a spanning-tree network that has all sw...; Question 438: When troubleshooting Ethernet connectivity issues, how can y...; Question 439: What is one reason that WPA encryption is preferred over WEP...; Question 440: Refer to the exhibit. A technician has installed SwithchB an...; Question 441: What are two characteristics of SSH? (Choose two.)...; Question 442: Refer to the exhibit. Which statement describes DLCI 17? (Ex...; Question 443: Which two options are valid WAN connectivity methods? (Choos...; Question 444: A default Frame Relay WAN is classified as what type of phys...; Question 445: Refer to the exhibit. A technician is troubleshooting a host...; Question 446: What are two recommended ways of protecting network device c...; Question 447: When you are troubleshooting an ACL issue on a router, which...; Question 448: Which two statements about late collisions are true? (Choose...; Question 449: Which port state is introduced by Rapid-PVST?...; Question 450: A switch is configured with all ports assigned to vlan 2 wit...; Question 451: What are two drawbacks of implementing a link-state routing ...; Question 452: Refer to the topology shown in the exhibit. Which ports will...; Question 453: Refer to the exhibit. What set of commands was configured on...; Question 454: Which command can you enter to troubleshoot the failure of a...; Question 455: Which statement about VLAN configuration is true?...; Question 456: Which three options are switchport configurations that can a...; Question 457: Refer to the exhibit. The two connected ports on the switch ...; Question 458: Which feature allows a device to use a switch port that is c...; Question 459: Which component of the Cisco SDN solution serves as the cent...; Question 460: Refer to the graphic. It has been decided that Workstation 1...; Question 461: Refer to the exhibit. The following commands are executed on...; Question 462: What is true about Ethernet? (Choose two.)...; Question 463: What is the default VLAN on an access port?...; Question 464: Under which circumstance should a network administrator impl...; Question 465: In which STP state does MAC address learning take place on a...; Question 466: Refer to the exhibit. Why has this switch not been elected t...; Question 467: Which two command can you enter to display the current time ...; Question 468: Refer to the exhibit. The output that is shown is generated ...; Question 469: Which two statements about stacking Cisco switches are true?...; Question 470: What does traffic shaping do to reduce congestion in a netwo...; Question 471: Refer to the exhibit. Hosts in network 192.168.2.0 are unabl...; Question 472: Which three statements are typical characteristics of VLAN a...; Question 473: Refer to the exhibit. How many broadcast domains exist in th...; Question 474: Which two statements about 1000BASE-T UTP cable are true? (C...; Question 475: What will be the result if the following configuration comma...; Question 476: Which option describes a benefit of a point-to-point leased ...; Question 477: Which protocol supports sharing the VLAN configuration betwe...; Question 478: Based on the output below, which two statements are true of ...; Question 479: Refer to the exhibit. The network administrator has created ...; Question 480: Which statement about DHCP snooping is true?...; Question 481: Which technology supports multiple dynamic secure connection...; Question 482: Scenario (Exhibit) An administrator is trying to ping and te...; Question 483: Which command is used to know the duplex speed of serial lin...; Question 484: (Exhibit) Refer to the exhibit. All switch ports are assigne...; Question 485: What are the possible trunking modes for a switch port? (Cho...; Question 486: Which command is used to enable CHAP authentication whit PAP...; Question 487: When is a routing table entry identified as directly connect...; Question 488: Refer to the exhibit. (Exhibit) The network administrator ca...; Question 489: Which command would you configure globally on a Cisco router...; Question 490: How can you manually configure a switch so that it is select...; Question 491: RouterA is unable to reach RouterB. Both routers are running...; Question 492: Which statement about QoS default behavior is true?...; Question 493: Refer to the exhibit. An attempt to deny web access to a sub...; Question 494: All WAN links inside the ABC University network use PPP with...; Question 495: Which type of topology is required by DMVPN?...; Question 496: Refer to the exhibit. Which two statements are true of the i...; Question 497: What is the authoritative source for an address lookup?...; Question 498: Refer to the exhibit. A technician has installed SwitchB and...; Question 499: Which configuration can be used with PAT to allow multiple i...; Question 500: Which two protocols can detect native VLAN mismatch errors? ...; Question 501: Refer to the exhibit. What is the effect of the configuratio...; Question 502: Which cloud service is typically used to provide DNS and DHC...; Question 503: In which STP state does MAC address learning take place on a...; Question 504: What are two reasons a network administrator would use CDP? ...; Question 505: Which technology supports the stateless assignment of IPv6 a...; Question 506: Which value indicates the distance from the NTP authoritativ...; Question 507: Refer to the topology below and answer the following questio...; Question 508: Instructions: - Enter IOS commands on the device to verify n...; Question 509: Refer to the exhibit. The network administrator is in a camp...; Question 510: Which of the following describes the roles of devices in a W...; Question 511: Which function allows EIGRP peers to receive notice of imple...; Question 512: Instructions This item contains several questions that you m...; Question 513: Which two statistics appear in show frame-relay map output? ...; Question 514: Refer to the exhibit. A network administrator is adding two ...; Question 515: Which feature facilitates the tagging of frames on a specifi...; Question 516: Which command is needed to send RIPv2 updates as broadcast w...; Question 517: In which circumstance are multiple copies of the same unicas...; Question 518: Which statement about RADIUS security is true?...; Question 519: Refer to the exhibit. What is the meaning of the output MTU ...; Question 520: Which WAN topology provides a direct connection from each si...; Question 521: Which Type of ipv6 unicast ip address is reachable across th...; Question 522: Which command can you enter on a Cisco IOS device to enable ...; Question 523: An administrator issues the show ip interface s0/0 command a...; Question 524: Which characteristics are representative of a link-state rou...; Question 525: (Exhibit) Refer to the exhibit. After you apply the given co...; Question 526: In GLBP, which router will respond to client ARP requests?...; Question 527: Which major component of the network virtualization architec...; Question 528: Scenario Refer to the topology. Your company has decided to ...; Question 529: Which three features are represented by the letter A in AAA ...; Question 530: Which three of these statements regarding 802.1Q trunking ar...; Question 531: Which option describes how a switch in rapid PVST+ mode resp...; Question 532: Which two server types are used to support DNS lookup? (Choo...; Question 533: (Exhibit) Refer to the exhibit. Which user-mode password has...; Question 534: Refer to the exhibit. Which two statements are true about in...; Question 535: Which of the following are types of flow control? (Choose th...; Question 536: Which two statements about IPv4 multicast traffic are true? ...; Question 537: Which two circumstances can cause collision domain issues on...; Question 538: Which encapsulation type is a Frame Relay encapsulation type...; Question 539: Which VTP mode cannot make a change to vlan?...; Question 540: What is the default lease time for a DHCP binding?...; Question 541: What is the function of the command switchport trunk native ...; Question 542: Which two statements about static NAT translations are true?...; Question 543: What are three reasons that an organization with multiple br...; Question 544: The following configuration line was added to router R1 Acce...; Question 545: Which two statements about floating static routes are true? ...; Question 546: Which IPv6 address is valid?; Question 547: Which Cisco platform can verify ACLs?...; Question 548: Which routing protocol has the smallest default administrati...; Question 549: Which two elements are fields in an Ethernet frame? (Choose ...; Question 550: Which command can you enter to determine whether serial inte...; Question 551: Which command can you enter on a switch to display the IP ad...; Question 552: Which three statements about DWDM are true? (Choose three)...; Question 553: Refer to the exhibit. What set of commands was configured on...; Question 554: Which command can you enter to block HTTPS traffic from the ...; Question 555: What happens when an 802.11a node broadcasts within the rang...; Question 556: Based on the output below from SwitchB, which statement is t...; Question 557: Which two statements about the tunnel mode ipv6ip command ar...; Question 558: Which two tasks does a router perform when it receives a pac...; Question 559: Which statement describes the process of dynamically assigni...; Question 560: What are two benefits of private IPv4 IP addresses? (Choose ...; Question 561: Scenario (Exhibit) An administrator is trying to ping and te...; Question 562: What is the first 24 bits in a MAC address called?...; Question 563: Which action can change the order of entries in a named acce...; Question 564: Which option is the main function of congestion management?...; Question 565: While troubleshooting a connectivity issue from a PC you obt...; Question 566: Which option describes the purpose of traffic policing?...; Question 567: Which Cisco Catalyst feature automatically disables the port...; Question 568: Which three circumstances can cause a GRE tunnel to be in an...; Question 569: Which HSRP feature was new in HSRPv2?...; Question 570: Which feature can you use to monitor traffic on a switch by ...; Question 571: Which configuration command can you apply to a HSRP router s...; Question 572: Refer to the exhibit. A problem with network connectivity ha...; Question 573: Instructions This item contains several questions that you m...; Question 574: Which IPv6 address is the all-router multicast group?...; Question 575: An administrator must assign static IP addresses to the serv...; Question 576: Under normal operations, Cisco recommends that you configure...; Question 577: On a corporate network, hosts on the same VLAN can communica...; Question 578: Scenario Refer to the topology. Your company has decided to ...; Question 579: What are three approaches that are used when migrating from ...; Question 580: Refer to the exhibit. The Bigtime router is unable to authen...; Question 581: Which two pieces of information are provided by the show con...; Question 582: For which two protocols can PortFast alleviate potential hos...; Question 583: Which technology allows a large number of private IP address...; Question 584: The Company WAN is migrating from RIPv1 to RIPv2. Which thre...; Question 585: Refer to the exhibit. What is the reason that the interface ...; Question 586: Which mode is compatible with Trunk, Access, and desirable p...; Question 587: Which three are valid modes for a switch port used as a VLAN...; Question 588: Refer to the topology below and answer the following questio...; Question 589: Refer to the exhibit. The switches on a campus network have ...; Question 590: Refer to the exhibit. An administrator pings the default gat...; Question 591: Which two passwords must be supplied in order to connect by ...; Question 592: Which two commands can be used to verify a trunk link config...; Question 593: Which statement about native VLAN traffic is true?...; Question 594: Which two neighbor types are supported in a BGP environment?...; Question 595: Which two statements about MPLS are true? (Choose two.)...; Question 596: Which EIGRP for IPv6 command can you enter to view the link-...; Question 597: Which command can you enter to configure the switch as an au...; Question 598: Which protocol is a Cisco proprietary implementation of STP?...; Question 599: Which three options are switchport configurations that can a...; Question 600: Refer to the exhibit. Which statement describes the effect o...; Question 601: Which option is a benefit of switch stacking?...; Question 602: Which statement about LLDP is true?...; Question 603: What is the function of the command switchport trunk native ...; Question 604: Which statements is true about Router on Stick?...

Question 484/604

LEAVE A REPLY

Download PDF File