200-125 Exam Dumps | Users on the 172.17.22.0 network cannot reach the server located on the 172.31.5.0 network. The network

Valid 200-125 Dumps shared by ExamDiscuss.com for Helping Passing 200-125 Exam! ExamDiscuss.com now offer the newest 200-125 exam dumps, the ExamDiscuss.com 200-125 exam questions have been updated and answers have been corrected get the newest ExamDiscuss.com 200-125 dumps with Test Engine here:

Access 200-125 Dumps Premium Version
(754 Q&As Dumps, 35%OFF Special Discount Code: freecram)

<< Prev Question Next Question >>

Question 83/317

Users on the 172.17.22.0 network cannot reach the server located on the 172.31.5.0 network. The network administrator connected to router Coffee via the console port, issued the show ip routecommand, and was able to ping the server.

Based on the output of the show ip route command and the topology shown in the graphic, what is the cause of the failure?

A. The network has not fully converged.

B. The neighbor relationship table is not correctly updated.

C. A static route is configured incorrectly.

D. The FastEthernet interface on Coffee is disabled.

E. IP routing is not enabled.

F. The routing table on Coffee has not updated .

Question List (317q): Question 1: Refer to the exhibit. The network administrator must establi...; Question 2: Refer to the exhibit. Which of these statements correctly de...; Question 3: What can be done to secure the virtual terminal interfaces o...; Question 4: A network administrator is configuring ACLs on a Cisco route...; Question 5: VLAN 3 is not yet configured on your switch. What happens if...; Question 6: Refer to the exhibit. A network administrator is adding two ...; Question 7: When a router undergoes the exchange protocol within OSPF, i...; Question 8: What are three reasons that an organization with multiple br...; Question 9: Refer to the exhibit. (Exhibit) All switch ports are assigne...; Question 10: A network administrator needs to configure port security on ...; Question 11: In an Ethernet network, under what two scenarios can devices...; Question 12: Which two statements describe characteristics of IPv6 unicas...; Question 13: What are three approaches that are used when migrating from ...; Question 14: Refer to the exhibit. (Exhibit) The network administrator ca...; Question 15: Which set of commands is recommended to prevent the use of a...; Question 16: Refer to the exhibit. (Exhibit) The network shown in the dia...; Question 17: As a network technician, do you know which are valid modes f...; Question 18: Which type of EIGRP route entry describes a feasible success...; Question 19: The output of the show frame-relay pvccommand shows "PVC STA...; Question 20: Refer to the exhibit. What can be determined about the route...; Question 21: You have been asked to come up with a subnet mask that will ...; Question 22: The network administrator has asked you to check the status ...; Question 23: What command visualizes the general NetFlow data on the comm...; Question 24: Which three statements about the features of SNMPv2 and SNMP...; Question 25: Refer to the exhibit. When running EIGRP, what is required f...; Question 26: Switch ports operating in which two roles will forward traff...; Question 27: Which encapsulation type is a Frame Relay encapsulation type...; Question 28: Which are valid modes for a switch port used as a VLAN trunk...; Question 29: Refer to the exhibit. Why has this switch not been elected t...; Question 30: Which three statements accurately describe Layer 2 Ethernet ...; Question 31: Which item represents the standard IP ACL?...; Question 32: What would be the effect of issuing the command access-group...; Question 33: Refer to the exhibit. Hosts on the same VLAN can communicate...; Question 34: Refer to the exhibit. The Bigtime router is unable to authen...; Question 35: Refer to the exhibit. What type of connection would be suppo...; Question 36: What are three advantages of VLANs? (Choose three.)...; Question 37: Refer to the exhibit. A network associate needs to configure...; Question 38: Which command displays CPU utilization?...; Question 39: Which three statements about Syslog utilization are true? (C...; Question 40: Refer to the exhibit. (Exhibit) C-router is to be used as a ...; Question 41: Refer to the exhibit. (Exhibit) What is the cause of the Sys...; Question 42: (Exhibit) Refer to the exhibit. What is the effect of the co...; Question 43: An administrator must assign static IP addresses to the serv...; Question 44: Given an IP address 172.16.28.252 with a subnet mask of 255....; Question 45: What is the function of the command switchport trunk native ...; Question 46: What is the purpose of Inverse ARP?...; Question 47: What authentication type is used by SNMPv2?...; Question 48: On a corporate network, hosts on the same VLAN can communica...; Question 49: Which of the following protocols uses both TCP and UDP ports...; Question 50: Which of these represents an IPv6 link-local address?...; Question 51: Refer to the graphic. (Exhibit) Host A is communicating with...; Question 52: Which will fix the issue and allow ONLY ping to work while k...; Question 53: Refer to the exhibit. Given the output for this command, if ...; Question 54: Which IPv6 address is valid?; Question 55: At which layer of the OSI model does the IPSec operate?...; Question 56: Which one of these is a valid HSRP Virtual Mac Address?...; Question 57: Which statement describes the process of dynamically assigni...; Question 58: What should be done prior to backing up an IOS image to a TF...; Question 59: A user is unable to connect to the Internet. Based on the la...; Question 60: Refer to the exhibit. For what two reasons has the router lo...; Question 61: In a switched environment, what does the IEEE 802.1Q standar...; Question 62: Which commands are required to properly configure a router t...; Question 63: Refer to the exhibit. What is the meaning of the term dynami...; Question 64: What will happen if a private IP address is assigned to a pu...; Question 65: What are two advantages of Layer 2 Ethernet switches over hu...; Question 66: Assuming the default switch configuration, which VLAN range ...; Question 67: When a DHCP server is configured, which two IP addresses sho...; Question 68: Refer to the exhibit. Each of these four switches has been c...; Question 69: Refer to the exhibit. Hosts in network 192.168.2.0 are unabl...; Question 70: Which statement describes VRRP object tracking?...; Question 71: Refer to the exhibit. What two results would occur if the hu...; Question 72: Refer to the exhibit. Which subnet mask will place all hosts...; Question 73: Refer to the exhibit. (Exhibit) The Lakeside Company has the...; Question 74: Refer to the exhibit. Given the output shown from this Cisco...; Question 75: The network administrator needs to address seven LANs. RIP v...; Question 76: In which solution is a router ACL used?...; Question 77: Refer to the exhibit. The output that is shown is generated ...; Question 78: Match the items on the left with appropriate OSI layer on th...; Question 79: Host 1 is trying to communicate with Host 2. The e0 interfac...; Question 80: Which statement about access lists that are applied to an in...; Question 81: What is the difference between a CSU/DSU and a modem?...; Question 82: (Exhibit) What set of comamands was configured on interface ...; Question 83: Users on the 172.17.22.0 network cannot reach the server loc...; Question 84: Which term describes the process of encapsulating IPv6 packe...; Question 85: Which destination addresses will be used by Host A to send d...; Question 86: In a GLBP network, who is responsible for the arp request?...; Question 87: Which command enables IPv6 forwarding on a Cisco router?...; Question 88: Which two commands can be used to verify a trunk link config...; Question 89: Refer to the exhibit. (Exhibit) A technician has installed S...; Question 90: Routing has been configured on the local router with these c...; Question 91: Refer to the exhibit. (Exhibit) What is the reason that the ...; Question 92: Refer to the graphic. A static route to the 10.5.6.0/24 netw...; Question 93: Which two statements about using the CHAP authentication mec...; Question 94: Refer to the exhibit. Which switch provides the spanning-tre...; Question 95: A network administrator creates a layer 3 EtherChannel, bund...; Question 96: A receiving host computes the checksum on a frame and determ...; Question 97: Refer to the exhibit. Which statement describes DLCI 17? (Ex...; Question 98: Refer to the exhibit. The following commands are executed on...; Question 99: Three switches are connected to one another via trunk ports....; Question 100: Which three statements about RSTP are true? (Choose Three)...; Question 101: Refer to Exhibit: (Exhibit) Based on the network shown in th...; Question 102: Which command shows your active Telnet connections?...; Question 103: Which three approaches can be used while migrating from an I...; Question 104: At which layer of the OSI model does PPP perform?...; Question 105: Refer to the exhibit. According to the routing table, where ...; Question 106: A network engineer wants to allow a temporary entry for a re...; Question 107: Which three features are added in SNMPv3 over SNMPv2?...; Question 108: The command frame-relay map ip 10.121.16.8 102 broadcastwas ...; Question 109: Which two statements about the OSPF Router ID are true? (Cho...; Question 110: Which protocol can cause overload on a CPU of a managed devi...; Question 111: What is the default Syslog facility level?...; Question 112: What Cisco IOS feature can be enabled to pinpoint an applica...; Question 113: (Exhibit) If the router Cisco returns the given output and h...; Question 114: For what two purposes does the Ethernet protocol use physica...; Question 115: What would be the effect of issuing the command ip access-gr...; Question 116: EIGRP Simulation After adding Interior router, no routing up...; Question 117: Which of the following correctly describe steps in the OSI d...; Question 118: Refer to the exhibit. Switch port FastEthernet 0/24 on ALSwi...; Question 119: How does a DHCP server dynamically assign IP addresses to ho...; Question 120: Refer to the exhibit. Which WAN protocol is being used? (Exh...; Question 121: A Cisco router is booting and has just completed the POST pr...; Question 122: What command instructs the device to timestamp Syslog debug ...; Question 123: Cisco Catalyst switches CAT1 and CAT2 have a connection betw...; Question 124: Which protocol is an open standard protocol framework that i...; Question 125: Why do large OSPF networks use a hierarchical design? (Choos...; Question 126: What is the alternative notation for the IPv6 address B514:8...; Question 127: Refer to the exhibit. Which three statements correctly descr...; Question 128: Refer to the exhibit. A new subnet with 60 hosts has been ad...; Question 129: A national retail chain needs to design an IP addressing sch...; Question 130: What will be the result if the following configuration comma...; Question 131: Refer to the exhibit. (Exhibit) The network administrator re...; Question 132: What functions do routers perform in a network? (Choose two)...; Question 133: Drag the Frame Relay acronym on the left to match its defini...; Question 134: What parameter can be different on ports within an EtherChan...; Question 135: Which address range efficiently summarizes the routing table...; Question 136: What are the possible trunking modes for a switch port? (Cho...; Question 137: Refer to the exhibit. What type of connection would be suppo...; Question 138: Refer to the exhibit. In this VLSM addressing scheme, what s...; Question 139: If IP routing is enabled, which two commands set the gateway...; Question 140: Which layer in the OSI reference model is responsible for de...; Question 141: Refer to the Exhibit. (Exhibit) Assuming that the entire net...; Question 142: Which two locations can be configured as a source for the IO...; Question 143: Which command enables RSTP on a switch?...; Question 144: (Exhibit) A network administrator is configuring an EtherCha...; Question 145: Which IPv6 address is the all-router multicast group?...; Question 146: Which two are advantages of static routing when compared to ...; Question 147: Which command enhances the 802.1D convergence time on ports ...; Question 148: In GLBP, which router will respond to client ARP requests?...; Question 149: Where does routing occur within the DoD TCP/IP reference mod...; Question 150: Refer to the exhibit. (Exhibit) An attempt to deny web acces...; Question 151: How many subnets can be gained by subnetting 172.17.32.0/23 ...; Question 152: Which command is used to display the collection of OSPF link...; Question 153: Refer to the exhibit. Given this output for SwitchC, what sh...; Question 154: Refer to the exhibit. A network associate has configured OSP...; Question 155: Which three are characteristics of an IPv6 anycast address? ...; Question 156: What are three components that comprise the SNMP framework? ...; Question 157: Which Layer 2 protocol encapsulation type supports synchrono...; Question 158: (Exhibit) If the devices produced the given output, what is ...; Question 159: Which two protocols are used by bridges and/or switches to p...; Question 160: What command sequence will configure a router to run OSPF an...; Question 161: Refer to the exhibit. An administrator pings the default gat...; Question 162: Refer to the exhibit. Which address and mask combination rep...; Question 163: What OSPF command, when configured, will include all interfa...; Question 164: What is the alert message generated by SNMP agents called ?...; Question 165: Which command can be used from a PC to verify the connectivi...; Question 166: Refer to the exhibit. Which three statements are true about ...; Question 167: In which circumstance are multiple copies of the same unicas...; Question 168: Which two of these statements regarding RSTP are correct? (C...; Question 169: Refer to the exhibit. The two exhibit devices are the only C...; Question 170: Which statement is correct regarding the operation of DHCP?...; Question 171: Refer to the exhibit. (Exhibit) Based on the exhibited routi...; Question 172: What are three reasons to collect Netflow data on a company ...; Question 173: Which command can be used to verify the DLCI destination add...; Question 174: On which options are standard access lists based?...; Question 175: Why is flash memory erased prior to upgrading the IOS image ...; Question 176: Why will a switch never learn a broadcast address?...; Question 177: Refer to the topology and router output shown in the exhibit...; Question 178: What SNMP message alerts the manager to a condition on the n...; Question 179: A network interface port has collision detection and carrier...; Question 180: It has become necessary to configure an existing serial inte...; Question 181: (Exhibit) A frame on VLAN 1 on switch S1 is sent to switch S...; Question 182: Refer to the exhibit. (Exhibit) Host A pings interface S0/0 ...; Question 183: Refer to the exhibit. A junior network administrator was giv...; Question 184: The left describes the types of cables, while the right desc...; Question 185: The network administrator is asked to configure 113 point-to...; Question 186: What are three benefits of GLBP? (Choose three.)...; Question 187: Refer to the diagram. All hosts have connectivity with one a...; Question 188: Refer to the exhibit. The company uses EIGRP as the routing ...; Question 189: Before installing a new, upgraded version of the IOS, what s...; Question 190: Users have been complaining that their Frame Relay connectio...; Question 191: A network administrator enters the following command on a ro...; Question 192: What is the first 24 bits in a MAC address called?...; Question 193: What is a global command?; Question 194: Refer to the exhibit. (Exhibit) Router1 was just successfull...; Question 195: Which two commands correctly verify whether port security ha...; Question 196: Refer to the exhibit. (Exhibit) What is the most efficient s...; Question 197: Refer to the exhibit. Switch-1 needs to send data to a host ...; Question 198: A network administrator is troubleshooting an EIGRP problem ...; Question 199: Refer to the exhibit. The networks connected to router R2 ha...; Question 200: Which command would you use on a Cisco router to verify the ...; Question 201: Which of the following are benefits of VLANs? (Choose three....; Question 202: Which two descriptions are correct about characteristics of ...; Question 203: Which command would you configure globally on a Cisco router...; Question 204: What is the default maximum number of equal-cost paths that ...; Question 205: When you are troubleshooting an ACL issue on a router, which...; Question 206: Refer to the exhibit. (Exhibit) Statements A, B, C, and D of...; Question 207: A network administrator is explaining VTP configuration to a...; Question 208: A router receives information about network 192.168.10.0/24 ...; Question 209: Which statements describe the routing protocol OSPF? (Choose...; Question 210: What are the three things that the Netflow uses to consider ...; Question 211: Refer to the exhibit. What is the most appropriate summariza...; Question 212: Which statement describes the process ID that is used to run...; Question 213: You are working in a data center environment and are assigne...; Question 214: A router has two Fast Ethernet interfaces and needs to conne...; Question 215: Which two states are the port states when RSTP has converged...; Question 216: Which subnet mask would be appropriate for a network address...; Question 217: Refer to the exhibit. All of the routers in the network are ...; Question 218: What is the default administrative distance of OSPF?...; Question 219: What are three features of the IPv6 protocol? (Choose three....; Question 220: Which three are the components of SNMP? (Choose three)...; Question 221: Which command can you use to manually assign a static IPv6 a...; Question 222: How is an EUI-64 format interface ID created from a 48-bit M...; Question 223: What occurs on a Frame Relay network when the CIR is exceede...; Question 224: Which PPP subprotocol negotiates authentication options?...; Question 225: Two routers named Atlanta and Brevard are connected by their...; Question 226: Refer to the topology shown in the exhibit. Which ports will...; Question 227: What are three values that must be the same within a sequenc...; Question 228: Refer to the exhibit. What commands must be configured on th...; Question 229: Refer to the exhibit. (Exhibit) HostA cannot ping HostB. Ass...; Question 230: Which command allows you to verify the encapsulation type (C...; Question 231: Which port state is introduced by Rapid-PVST?...; Question 232: Refer to the exhibit. A network administrator configures a n...; Question 233: What are two enhancements that OSPFv3 supports over OSPFv2? ...; Question 234: What command is used to verify the DLCI destination address ...; Question 235: Refer to the exhibit. Which two statements are true of the i...; Question 236: How many broadcast domains are shown in the graphic assuming...; Question 237: Which parameter would you tune to affect the selection of a ...; Question 238: Refer to the exhibit. The technician wants to upload a new I...; Question 239: A network administrator is troubleshooting the OSPF configur...; Question 240: Refer to the exhibit. (Exhibit) In the Frame Relay network, ...; Question 241: Refer to the exhibit. PC_1 is sending packets to the FTP ser...; Question 242: Refer to the exhibit. Which two statements are true about in...; Question 243: Which two benefits are provided by creating VLANs? (Choose t...; Question 244: Which two link protocols are used to carry multiple VLANs ov...; Question 245: What is the effect of using the service password-encryptionc...; Question 246: A network administrator needs to configure a serial link bet...; Question 247: What are three benefits of implementing VLANs? (Choose three...; Question 248: Drag the Cisco default administrative distance to the approp...; Question 249: Which three elements must be used when you configure a route...; Question 250: A network administrator is trying to add a new router into a...; Question 251: Which Cisco Catalyst feature automatically disables the port...; Question 252: Refer to the exhibit. The two connected ports on the switch ...; Question 253: Refer to the graphic. R1 is unable to establish an OSPF neig...; Question 254: Refer to the exhibit. What will Router1 do when it receives ...; Question 255: Which two are features of IPv6? (Choose two.)...; Question 256: Which option is a valid IPv6 address?...; Question 257: Refer to the exhibit. FTP Server is sending packets to the P...; Question 258: Which two of these are characteristics of the 802.1Q protoco...; Question 259: What is SNMPv2 authentication protocol....; Question 260: Which two statistics appear in show frame-relay map output? ...; Question 261: Which command is used to enable CHAP authentication, with PA...; Question 262: What is known as "one-to-nearest" addressing in IPv6?...; Question 263: Which characteristics are representative of a link-state rou...; Question 264: Refer to the exhibit. What statement is true of the configur...; Question 265: Refer to the exhibit. What could be possible causes for the ...; Question 266: Which three statements about HSRP operation are true? (Choos...; Question 267: The network administrator has been asked to give reasons for...; Question 268: Refer to the exhibit. (Exhibit) A problem with network conne...; Question 269: Which two statements are true about the command ip route 172...; Question 270: Drag each category on the left to its corresponding router o...; Question 271: A network administrator is verifying the configuration of a ...; Question 272: How does using the service password-encryptioncommand on a r...; Question 273: Refer to the Exhibit. (Exhibit) All switch ports are assigne...; Question 274: Drag and drop. Match the items on the left with its correspo...; Question 275: What does a Layer 2 switch use to decide where to forward a ...; Question 276: Which command is necessary to permit SSH or Telnet access to...; Question 277: Which is true about OSPF router-id? (Choose two .)...; Question 278: Drag the security feature on the left to the specific securi...; Question 279: Refer to the exhibit. What is the meaning of the output MTU ...; Question 280: At which layer of the OSI model is RSTP used to prevent loop...; Question 281: A network administrator changes the configuration register t...; Question 282: Which parameter or parameters are used to calculate OSPF cos...; Question 283: Refer to the exhibit. (Exhibit) Based on the information giv...; Question 284: What two things will a router do when running a distance vec...; Question 285: Which three of these statements regarding 802.1Q trunking ar...; Question 286: A corporation wants to add security to its network. The requ...; Question 287: Refer to the exhibit. (Exhibit) The network administrator no...; Question 288: What is one benefit of PVST+?; Question 289: What value is primarily used to determine which port becomes...; Question 290: Which router IOS commands can be used to troubleshoot LAN co...; Question 291: Which command encrypts all plaintext passwords?...; Question 292: Which two statements about static NAT translation are true? ...; Question 293: What information does a router running a link-state protocol...; Question 294: Syslog was configured with a level 3 trap. Which 3 types of ...; Question 295: Refer to the exhibit. When running OSPF, What would cause ro...; Question 296: Which of the following statements describe the network shown...; Question 297: Which two of these statements are true of IPv6 address repre...; Question 298: What Netflow component can be applied to an interface to tra...; Question 299: Refer to the exhibit. A network technician is asked to desig...; Question 300: Which command reveals the last method used to powercycle a r...; Question 301: Refer to the exhibit. At the end of an RSTP election process...; Question 302: What are two benefits of using NAT? (Choose two)...; Question 303: RouterA is unable to reach RouterB. Both routers are running...; Question 304: List 3 components of SNMP ?; Question 305: Refer to the exhibit. (Exhibit) The speed of all serial link...; Question 306: Which device might be installed at a branch office to enable...; Question 307: A company is installing IP phones. The phones and office com...; Question 308: What are two characteristics of Frame Relay point-to-point s...; Question 309: Which switch would STP choose to become the root bridge in t...; Question 310: What are the popular destinations for Syslog messages to be ...; Question 311: Refer to the exhibit. (Exhibit) A network administrator atte...; Question 312: What is the result of issuing the frame-relay map ip 192.168...; Question 313: Which IPv6 address is the equivalent of the IPv4 interface l...; Question 314: What are the benefits of using Netflow? (Choose three.)...; Question 315: Which IEEE standard protocol is initiated as a result of suc...; Question 316: A network administrator needs to allow only one Telnet conne...; Question 317: What are two benefits of using a single OSPF area network de...

Question 83/317

LEAVE A REPLY

Download PDF File