200-105 Exam Dumps | Which statements are true about EIGRP successor routes? (Choose two.)

Valid 200-105 Dumps shared by ExamDiscuss.com for Helping Passing 200-105 Exam! ExamDiscuss.com now offer the newest 200-105 exam dumps, the ExamDiscuss.com 200-105 exam questions have been updated and answers have been corrected get the newest ExamDiscuss.com 200-105 dumps with Test Engine here:

Access 200-105 Dumps Premium Version
(775 Q&As Dumps, 35%OFF Special Discount Code: freecram)

<< Prev Question Next Question >>

Question 63/325

Which statements are true about EIGRP successor routes? (Choose two.)

A. A successor route is used by EIGRP to forward traffic to a destination.

B. Successor routes are saved in the topology table to be used if the primary route fails.

C. Successor routes are flagged as 'active' in the routing table.

D. A successor route may be backed up by a feasible successor route.

E. Successor routes are stored in the neighbor table following the discovery process.

Question List (325q): Question 1: Refer to the exhibit. Which WAN protocol is being used? (Exh...; Question 2: Which three statements about VTP features are true? (Choose ...; Question 3: Refer to the exhibit. A frame on VLAN 1 on switch S1 is sent...; Question 4: What is the default administrative distance of the OSPF rout...; Question 5: Which channel mode is available to static EhterChannels?...; Question 6: Which command do you enter to verify that a VLAN has been re...; Question 7: Which two statements about the OSPF Router ID are true? (Cho...; Question 8: What is the default DTP mode on a switch port?...; Question 9: What are the two default metrics used by EIGRP for route sel...; Question 10: Refer to the topology and partial router configurations show...; Question 11: Refer to the exhibit. The user at Workstation B reports that...; Question 12: Refer to the exhibit. What command sequence will enable PAT ...; Question 13: What is the purpose of LCP?; Question 14: Refer to the exhibit. Which address range efficiently summar...; Question 15: Which two statements about using the CHAP authentication mec...; Question 16: A network administrator has configured access list 173 to pr...; Question 17: The output of the show frame-relay pvc command shows "PVC ST...; Question 18: Refer to the exhibit. What is the meaning of the term dynami...; Question 19: How does using the service password-encryption command on a ...; Question 20: What three pieces of information can be used in an extended ...; Question 21: What is the result of issuing the frame-relay map ip 192.168...; Question 22: What are two enhancements that OSPFv3 supports over OSPFv2? ...; Question 23: Refer to the exhibit. Based on the exhibited routing table, ...; Question 24: Refer to the exhibit. Which command do you enter so that R1 ...; Question 25: In the Frame Relay network, which IP addresses would be assi...; Question 26: Which router command can be used to verify the type of cable...; Question 27: Which of the following are the valid numbers of standard ACL...; Question 28: Refer to the exhibit. A network technician enters the follow...; Question 29: Which command can be used from a PC to verify the connectivi...; Question 30: Which options are the two differences between HSRP versions ...; Question 31: A router has learned three possible routes that could be use...; Question 32: Which option describes a drawback of proxy ARP?...; Question 33: Refer to the exhibit. The router has been configured with th...; Question 34: What are three valid reasons to assign ports to VLANs on a s...; Question 35: Refer to the exhibit. A technician pastes the configurations...; Question 36: Refer to the exhibit. (Exhibit) While you troubleshoot a con...; Question 37: Which of the port is not part of STP protocol?...; Question 38: What is one benefit of PVST+?; Question 39: Which two are features of IPv6? (Choose two.)...; Question 40: Refer to the exhibit. Given the output for this command, if ...; Question 41: The internetwork infrastructure of company XYZ consists of a...; Question 42: What command is used to verify the DLCI destination address ...; Question 43: Which two Cisco IOS commands, used in troubleshooting, can e...; Question 44: Which statement about IPv6 is true?...; Question 45: Which form of NAT maps multiple private IP addresses to a si...; Question 46: Which two data integrity algorithms are commonly used in VPN...; Question 47: Which two statements about eBGP neighbor relationships are t...; Question 48: A network administrator is configuring ACLs on a Cisco route...; Question 49: Which HSRP Feature was new in HSRPv2?...; Question 50: Scenario Refer to the topology. Your company has decided to ...; Question 51: It has become necessary to configure an existing serial inte...; Question 52: Refer to the exhibit. C-router is to be used as a "router-on...; Question 53: Instructions This item contains several questions that you m...; Question 54: Which statement describes the process ID that is used to run...; Question 55: Refer to the exhibit. What can be concluded from the output ...; Question 56: Which command can you enter to determine whether a voice VLA...; Question 57: The company internetwork is subnetted using 29 bits. Which w...; Question 58: What about HSRP IP Address is true?...; Question 59: Two hosts are attached to a switch with the default configur...; Question 60: Scenario Refer to the topology. Your company has decided to ...; Question 61: Which purpose of the network command in the BGP configuratio...; Question 62: Refer to the exhibit. Given the partial configuration shown ...; Question 63: Which statements are true about EIGRP successor routes? (Cho...; Question 64: Which IEEE standard protocol is initiated as a result of suc...; Question 65: Refer to the exhibit. Which of these correctly describes the...; Question 66: Which three describe the reasons large OSPF networks use a h...; Question 67: Which encapsulation type is a Frame Relay encapsulation type...; Question 68: Refer to the exhibit. From R1, a network administrator is ab...; Question 69: Refer to the exhibit. The network associate is configuring O...; Question 70: Which information is provided by the output of the show snmp...; Question 71: Which command can you enter to assign an interface to the de...; Question 72: Refer to the exhibit. If the router Cisco returns the given ...; Question 73: Which of the following is needed to be enable back the role ...; Question 74: A router is running three routing processes: RIP, OSPF, and ...; Question 75: Which command enables RSTP on a switch?...; Question 76: Which pairing reflects a correct protocol-and-metric relatio...; Question 77: Refer to the exhibit. What statement is true of the configur...; Question 78: At which layer of the OSI model does PPP perform?...; Question 79: Two switches are connected through a trunk link. Which two c...; Question 80: The command show frame-relay map gives the following output:...; Question 81: A network administrator needs to configure port security on ...; Question 82: You are working in a data center environment and are assigne...; Question 83: Instructions Enter Cisco IOS commands on device to verify ne...; Question 84: What is true about Ethernet? (Choose two.)...; Question 85: Which IPv6 routing protocol uses multicast group FF02::9 to ...; Question 86: Which command allows you to verify the encapsulation type (C...; Question 87: SIMULATION You work as a network engineer for SASCOM Network...; Question 88: What are three characteristics of the OSPF routing protocol?...; Question 89: What is the Cisco recommended DSCP value for voice traffic?...; Question 90: Refer to the exhibit. Host A pings interface S0/0 on router ...; Question 91: Instructions Enter Cisco IOS commands on device to verify ne...; Question 92: Refer to the exhibit. Hosts in network 192.168.2.0 are unabl...; Question 93: Which command helps a network administrator to manage memory...; Question 94: Refer to the exhibit. HostA cannot ping HostB. Assuming rout...; Question 95: Which feature does PPP use to encapsulate multiple protocols...; Question 96: Instructions: Enter IOS commands on the Dubai router to veri...; Question 97: Which two actions must you take to configure a PAgP Ethernet...; Question 98: Refer to the exhibit. The company uses EIGRP as the routing ...; Question 99: Which two are advantages of static routing when compared to ...; Question 100: The network administrator of the Oregon router adds the foll...; Question 101: Which technology can provide security when connection multip...; Question 102: Scenario Refer to the topology. Your company has decided to ...; Question 103: What is the purpose of Inverse ARP?...; Question 104: Which two statements about static NAT translations are true?...; Question 105: A security administrator wants to profile endpoints and gain...; Question 106: Refer to the exhibit. At the end of an RSTP election process...; Question 107: Which value to use in HSRP protocol election process?...; Question 108: In which circumstance are multiple copies of the same unicas...; Question 109: Refer to the exhibit. Which two statements are true about th...; Question 110: Which two statistics appear in show frame-relay map output? ...; Question 111: Refer to the exhibit. What can be determined about the inter...; Question 112: In which solution is a router ACL used?...; Question 113: Which command do you enter to determine whether LACP is in u...; Question 114: Which command do you enter so that a port enters the forward...; Question 115: Which three effects of using local SPAN are true? (Choose th...; Question 116: Which command is used to display the collection of OSPF link...; Question 117: Which function does traffic shaping perform?...; Question 118: Instructions This item contains several questions that you m...; Question 119: What are OSPF's default hello and dead timers? (Choose two)...; Question 120: After you configure a GRE tunnel between two networks, the t...; Question 121: Which value is used to determine the active router in an HSR...; Question 122: Which feature or value must be configured to enable EIGRPv6?...; Question 123: Refer to the exhibit. The network is converged. After link-s...; Question 124: Which protocol provides a method of sharing VLAN configurati...; Question 125: At which layer of the OSI model is RSTP used to prevent loop...; Question 126: Select the action that results from executing these commands...; Question 127: Refer to the exhibit. Which route will be found in the routi...; Question 128: Which command is necessary to permit SSH or Telnet access to...; Question 129: Which two statements about VTP are true? (Choose two.)...; Question 130: Refer to the exhibit. What address is a feasible successor? ...; Question 131: Which Layer 2 protocol encapsulation type supports synchrono...; Question 132: When are packets processed by an inbound access list?...; Question 133: Given an IP address 172.16.28.252 with a subnet mask of 255....; Question 134: Which term describes a spanning-tree network that has all sw...; Question 135: Which IPv6 address is the equivalent of the IPv4 interface l...; Question 136: What is the minimum command to turn on encryption on SNMP?...; Question 137: Which two data link layers are supported by Cisco IOS Softwa...; Question 138: Which type does a port become when it receives the best BPDU...; Question 139: Refer to the exhibit. What commands must be configured on th...; Question 140: Which command must you enter to enable OSPFV2 in an IPV4 net...; Question 141: Which utility can you use to identify redundant or shadow ru...; Question 142: What does split horizon prevent?...; Question 143: A network administrator is configuring the routers in the gr...; Question 144: Refer to the exhibit. To what does the 128 refer in the rout...; Question 145: Which statement about access lists that are applied to an in...; Question 146: Which two options are valid WAN connectivity methods? (Choos...; Question 147: Instructions This item contains several questions that you m...; Question 148: Which command reveals the last method used to powercycle a r...; Question 149: Refer to the exhibit. Some 2950 series switches are connecte...; Question 150: A network administrator is troubleshooting an EIGRP problem ...; Question 151: Which IPv6 address is valid?; Question 152: Which command enables IPv6 forwarding on a Cisco router?...; Question 153: Which port state is introduced by Rapid-PVST?...; Question 154: Refer to the exhibit. Statements A, B, C, and D of ACL 10 ha...; Question 155: What does the frame-relay interface-dlci command configure?...; Question 156: What 8-bit field exists in IP packet for QoS?...; Question 157: Refer to the graphic. Users on the Holyoke router are unable...; Question 158: Which VLAN bridge priority value will make a switch as root ...; Question 159: Which two statements about MPLS are true? (Choose two.)...; Question 160: Which two statement about proxy ARP are true? (Choose two)...; Question 161: Refer to the exhibit. What three actions will the switch tak...; Question 162: Through which three states does a BGP routing process pass w...; Question 163: Refer to the exhibit. Assuming that the entire network topol...; Question 164: Which Layer 2 attack is specifically mitigated by changing t...; Question 165: Which three approaches can be used while migrating from an I...; Question 166: What does a router do if it has no EIGRP feasible successor ...; Question 167: What is the default administrative distance of OSPF?...; Question 168: Which set of commands is recommended to prevent the use of a...; Question 169: Which two statements describe characteristics of IPv6 unicas...; Question 170: Which two commands debug a PPPoE connection that has failed ...; Question 171: Refer to the topology shown in the exhibit. Which ports will...; Question 172: Which three commands do you use to verify that IPSec over a ...; Question 173: Which combination of values is valid for a router-on-a-stick...; Question 174: Which command can you enter in a network switch configuratio...; Question 175: What can be done to secure the virtual terminal interfaces o...; Question 176: Which statement is true, as relates to classful or classless...; Question 177: Refer to the exhibit. Which statement is true? (Exhibit)...; Question 178: Which term represents the minimum bandwidth provided in a Me...; Question 179: An organization is concerned that too many employees are was...; Question 180: What two options are causes of network slowness that can res...; Question 181: Which two authentication methods are compatible with MLPPP o...; Question 182: Which two types of cloud services may require you to alter t...; Question 183: A router has two Fast Ethernet interfaces and needs to conne...; Question 184: Workstation A has been assigned an IP address of 192.0.2.24/...; Question 185: An access list has been designed to prevent Telnet traffic f...; Question 186: If two OSPF neighbors have formed complete adjacency and are...; Question 187: Which component of an IPv6 OSPFv3 connection must be configu...; Question 188: Refer to the exhibit. How should Switch1 and Switch2 be conn...; Question 189: How can you manually configure a switch so that it is select...; Question 190: Refer to the exhibit. Given the output from the show ip eigr...; Question 191: Which protocol is a Cisco proprietary implementation of STP?...; Question 192: Which three statements about RSTP are true? (Choose three.)...; Question 193: For which reason can a GRE tunnel have an Up/DOWN status?...; Question 194: Refer to the exhibit. The show interfaces serial 0/1 command...; Question 195: Which statement about spanning-tree root-bridge election is ...; Question 196: Which two of these statements are true of IPv6 address repre...; Question 197: Refer to the exhibit. When running EIGRP, what is required f...; Question 198: The internetwork infrastructure of company XYZ consists of a...; Question 199: What occurs on a Frame Relay network when the CIR is exceede...; Question 200: What are three benefits of implementing VLANs? (Choose three...; Question 201: Which two of these statements regarding RSTP are correct? (C...; Question 202: Which two privileged mode Cisco IOS commands can be used to ...; Question 203: The following configuration is applied to a Layer 2 Switch: ...; Question 204: Which command do use we to see SNMP version?...; Question 205: Instructions This item contains several questions that you m...; Question 206: Refer to the exhibit. Given the output shown from this Cisco...; Question 207: Which WAN topology is most appropriate for a centrally locat...; Question 208: What is the default encapsulation type for Cisco WAN serial ...; Question 209: On which options are standard access lists based?...; Question 210: Which two statements describe the process identifier that is...; Question 211: Which feature can you use to restrict SNMP queries to a spec...; Question 212: When you are troubleshooting an ACL issue on a router, which...; Question 213: Which device might be installed at a branch office to enable...; Question 214: Instructions: Enter IOS commands on the Dubai router to veri...; Question 215: A network administrator needs to allow only one Telnet conne...; Question 216: What are three features of the IPv6 protocol? (Choose three....; Question 217: Refer to the exhibit. The following commands are executed on...; Question 218: What are two characteristics of a switch that is configured ...; Question 219: Refer to the exhibit. On R1 which routing protocol is in use...; Question 220: The command frame-relay map ip 10.121.16.8 102 broadcast was...; Question 221: You have been asked to come up with a subnet mask that will ...; Question 222: Which component of VPN technology ensures that data is unalt...; Question 223: Which encryption method does CHAP authentication use for the...; Question 224: Refer to the exhibit. A packet with a source IP address of 1...; Question 225: Which three are characteristics of an IPv6 anycast address? ...; Question 226: What is the maximum cost for hello and dead packets in OSPF?...; Question 227: Identify the four valid IPv6 addresses. (Choose four.)...; Question 228: Which two characteristics of stacked switches are true? (Cho...; Question 229: Which WAN solution is secured by default?...; Question 230: Refer to the exhibit. Which three EIGRP routes will be prese...; Question 231: Which statement describes an EIGRP feasible successor route?...; Question 232: Which type of attack can be mitigated by configuring the def...; Question 233: Instructions Enter Cisco IOS commands on device to verify ne...; Question 234: Which protocol should be used to establish a secure terminal...; Question 235: Which value must you configure on a device before EIGRP for ...; Question 236: Instructions: Enter IOS commands on the Dubai router to veri...; Question 237: Which command do you enter to determine the root priority?...; Question 238: Which mode is compatible with Trunk, Access, and desirable p...; Question 239: The network administrator is asked to configure 113 point-to...; Question 240: Refer to the exhibit. A network engineer is troubleshooting ...; Question 241: Assuming the default switch configuration, which VLAN range ...; Question 242: A network administrator wants to ensure that only the server...; Question 243: Which interface counter can you use to diagnose a duplex mis...; Question 244: A network administrator receives an error message while tryi...; Question 245: Which four options are the HSRP states for a router? (Choose...; Question 246: A network administrator must configure 200 switch ports to a...; Question 247: VLAN 3 is not yet configured on your switch. What happens if...; Question 248: Refer to the output from the show running-config command in ...; Question 249: What can cause two OSPF neighbors to be stuck in the EXSTART...; Question 250: Disadvantages of using proxy ARP?...; Question 251: Which option describes a benefit of a point-to-point leased ...; Question 252: Which two statements are characteristics of a distance vecto...; Question 253: Which type of EIGRP route entry describes a feasible success...; Question 254: A switch is configured with all ports assigned to vlan 2 wit...; Question 255: What can be done to Frame Relay to resolve split-horizon iss...; Question 256: A network administrator would like to implement NAT in the n...; Question 257: Refer to the exhibit. The output that is shown is generated ...; Question 258: Which address is the IPv6 all-RIP-routers multicast group ad...; Question 259: The ROUTE company has a small network. The network consists ...; Question 260: Which two commands correctly verify whether port security ha...; Question 261: What information does a router running a link-state protocol...; Question 262: What IP SLA ICMP Echo measures?...; Question 263: Which command do you enter to enable local authentication fo...; Question 264: A department decides to replace its hub with a Catalyst 2950...; Question 265: Refer to the exhibit. Which subnet mask will place all hosts...; Question 266: Refer to the exhibit. Assume that all of the router interfac...; Question 267: In which integration method is an IPv6 packet encapsulated w...; Question 268: Refer to the exhibit. How many interfaces on R1 should be co...; Question 269: What are two characteristics of Frame Relay point-to-point s...; Question 270: Which function allows EIGRP peers to receive notice of imple...; Question 271: What is the status of port-channel if LACP is misconfigured?...; Question 272: Refer to the exhibit. Each of these four switches has been c...; Question 273: What is the advantage of using a multipoint interface instea...; Question 274: What is the default maximum number of equal-cost paths that ...; Question 275: Refer to the exhibit. What information about the interfaces ...; Question 276: A network administrator needs to configure a serial link bet...; Question 277: Which command is used to enable CHAP authentication, with PA...; Question 278: About statement of HDLC IP address....; Question 279: What is the alternative notation for the IPv6 address B514:8...; Question 280: Which command displays the CHAP authentication process as it...; Question 281: Refer to the exhibit. A network associate has configured OSP...; Question 282: Refer to the exhibit. If RTR01 is configured as shown, which...; Question 283: What are three reasons that an organization with multiple br...; Question 284: What are two benefits of using NAT? (Choose two.)...; Question 285: A router receives information about network 192.168.10.0/24 ...; Question 286: Instructions: Enter IOS commands on the Dubai router to veri...; Question 287: Refer to the exhibit. Assume that all router interfaces are ...; Question 288: Which statement describes VRRP object tracking?...; Question 289: What can you change to select switch as root bridge?...; Question 290: Refer to the exhibit. Why has this switch not been elected t...; Question 291: Refer to the exhibit. Which two statements about the configu...; Question 292: Which command shows your active Telnet connections?...; Question 293: When a router undergoes the exchange protocol within OSPF, i...; Question 294: Refer to the exhibit. A technician is testing connection pro...; Question 295: A router has been configured to provide the nine users on th...; Question 296: Which name describes an IPv6 host-enabled tunneling techniqu...; Question 297: Refer to the exhibit. The ABC Company has the internetwork i...; Question 298: In order to comply with new auditing standards, a security a...; Question 299: What Netflow component can be applied to an interface to tra...; Question 300: (Exhibit) Refer to the exhibit. A technician has configured ...; Question 301: Which three elements must be used when you configure a route...; Question 302: Users have been complaining that their Frame Relay connectio...; Question 303: What OSPF command, when configured, will include all interfa...; Question 304: While troubleshooting a connection problem on a computer, yo...; Question 305: Which protocol is an open standard protocol framework that i...; Question 306: Which IPsec security protocol should be used when confidenti...; Question 307: Refer to the exhibit. If the router R1 returns the given out...; Question 308: Which command do you enter to verify an SVI?...; Question 309: (Exhibit) Refer to the exhibit. How will the router handle a...; Question 310: Which three options are benefits of using TACACS+ on a devic...; Question 311: Which utility do you use to view IP traffic that is switched...; Question 312: Which commands are required to properly configure a router t...; Question 313: Which command can be used from a router to verify the Layer ...; Question 314: Unauthorized users have used Telnet to gain access to a comp...; Question 315: Instructions Enter Cisco IOS commands on device to verify ne...; Question 316: Which three of these statements regarding 802.1Q trunking ar...; Question 317: Refer to the exhibit. Which switch provides the spanning-tre...; Question 318: What are three values that must be the same within a sequenc...; Question 319: What is the default value of the Read-Write-All-SNMP communi...; Question 320: What are two benefits of using a single OSPF area network de...; Question 321: Which functionality does an SVI provide?...; Question 322: Which parameter or parameters are used to calculate OSPF cos...; Question 323: Which parameter would you tune to affect the selection of a ...; Question 324: Which PPP subprotocol negotiates authentication options?...; Question 325: Which command can you enter on a switch to determine the cur...

Question 63/325

LEAVE A REPLY

Download PDF File