- Home
- CheckPoint
- Check Point Certified Security Expert Update - R80
- CheckPoint.156-915.80.v2018-11-13.q55
- Question 23
Valid 156-915.80 Dumps shared by ExamDiscuss.com for Helping Passing 156-915.80 Exam! ExamDiscuss.com now offer the newest 156-915.80 exam dumps, the ExamDiscuss.com 156-915.80 exam questions have been updated and answers have been corrected get the newest ExamDiscuss.com 156-915.80 dumps with Test Engine here:
Access 156-915.80 Dumps Premium Version
(500 Q&As Dumps, 35%OFF Special Discount Code: freecram)
<< Prev Question Next Question >>
Question 23/55
When simulating a problem on CLusterXL cluster with cphaprob -d STOP -s problem -t 0 register, to initiate a failover on an active cluster member, what command allows you remove the problematic state?
Correct Answer: A
Explanation/Reference:
Explanation:
esting a failover in a controlled manner using following command;
# cphaprob -d STOP -s problem -t 0 register
This will register a problem state on the cluster member this was entered on; If you then run;
# cphaprob list
this will show an entry named STOP.
to remove this problematic register run following;
# cphaprob -d STOP unregister
Reference: https://fwknowledge.wordpress.com/2013/04/04/manual-failover-of-the-fw-cluster/
Explanation:
esting a failover in a controlled manner using following command;
# cphaprob -d STOP -s problem -t 0 register
This will register a problem state on the cluster member this was entered on; If you then run;
# cphaprob list
this will show an entry named STOP.
to remove this problematic register run following;
# cphaprob -d STOP unregister
Reference: https://fwknowledge.wordpress.com/2013/04/04/manual-failover-of-the-fw-cluster/
- Question List (55q)
- Question 1: When deploying multiple clustered firewalls on the same subn...
- Question 2: You are working with multiple Security Gateways enforcing an...
- Question 3: What can you do to see the current number of kernel instance...
- Question 4: What is the responsibility of SOLR process on R80.10 managem...
- Question 5: When Dynamic Dispatcher is enabled, connections are assigned...
- Question 6: The following command is used to verify the CPUSE version:...
- Question 7: Why would you not see a CoreXL configuration option in cpcon...
- Question 8: The Correlation Unit performs all but which of the following...
- Question 9: Using mgmt_cli, what is the correct syntax to import a host ...
- Question 10: The "MAC magic" value must be modified under the following c...
- Question 11: When doing a Stand-Alone Installation, you would install the...
- Question 12: You noticed that CPU cores on the Security Gateway are usual...
- Question 13: Fill in the blank: The tool ___________ generates a R80 Secu...
- Question 14: Which packet info is ignored with Session Rate Acceleration?...
- Question 15: What are the three components for Check Point Capsule?...
- Question 16: The CDT utility supports which of the following?...
- Question 17: Which of the following statements is TRUE about R80 manageme...
- Question 18: Check Point APIs allow system engineers and developers to ma...
- Question 19: In R80 spoofing is defined as a method of:...
- Question 20: Tom has been tasked to install Check Point R80 in a distribu...
- Question 21: Fill in the blank: The R80 utility fw monitoris used to trou...
- Question 22: Fill in the blank: The R80 feature ________ permits blocking...
- Question 23: When simulating a problem on CLusterXL cluster with cphaprob...
- Question 24: You have existing dbedit scripts from R77. Can you use them ...
- Question 25: The Security Gateway is installed on GAiA R80. The default p...
- Question 26: When defining QoS global properties, which option below is n...
- Question 27: John detected high load on sync interface. Which is most rec...
- Question 28: What happen when IPS profile is set in Detect-Only Mode for ...
- Question 29: What is a feature that enables VPN connections to successful...
- Question 30: The Firewall kernel is replicated multiple times, therefore:...
- Question 31: Fill in the blank: The command _______________ provides the ...
- Question 32: SmartEvent does NOT use which of the following procedures to...
- Question 33: Which one of these is NOT a firewall chain?...
- Question 34: Sticky Decision Function (SDF) is required to prevent which ...
- Question 35: In SPLAT the command to set the timeout was idle. In order t...
- Question 36: Which directory below contains log files?...
- Question 37: Which of these options is an implicit MEP option?...
- Question 38: Which features are only supported with R80.10 Gateways but n...
- Question 39: SecureXL improves non-encrypted firewall traffic throughput ...
- Question 40: What is the purpose of Priority Delta in VRRP?...
- Question 41: Which is not a blade option when configuring SmartEvent?...
- Question 42: What makes Anti-Bot unique compared to other Threat Preventi...
- Question 43: What is the SOLR database for?
- Question 44: In which case is a Sticky Decision Function relevant?...
- Question 45: On R80.10 the IPS Blade is managed by:...
- Question 46: In Gaia, if one is unsure about a possible command, what com...
- Question 47: GAiA greatly increases operational efficiency by offering an...
- Question 48: VPN Tunnel Sharing can be configured with any of the options...
- Question 49: You want to store the GAiA configuration in a file for later...
- Question 50: Vanessa is expecting a very important Security Report. The D...
- Question 51: Which command collects diagnostic data for analyzing custome...
- Question 52: Full synchronization between cluster members is handled by F...
- Question 53: Which is a suitable command to check whether Drop Templates ...
- Question 54: What command would show the API server status?...
- Question 55: What is the purpose of a SmartEvent Correlation Unit?...
[×]
Download PDF File
Enter your email address to download CheckPoint.156-915.80.v2018-11-13.q55.pdf