<< Prev Question Next Question >>

Question 13/93

When using Monitor Sessions with a destination of the CPU, it is impossible to forward an entire 10Gbps worth of traffic due to internal COPP policies. How might you successfully use this feature given these constraints?

LEAVE A REPLY

Your email address will not be published. Required fields are marked *

Question List (93q)
2 commentQuestion 1: On an Arista switch, what two commands can you use to write ...
Question 2: True or False: XMPP Management is enabled by default....
Question 3: What is the abbreviation for the term used to describe a dev...
2 commentQuestion 4: If the SWI=statement in the boot-config file is invalid, wha...
Question 5: Which command would you use to change the SSH Idle timeout a...
Question 6: In what file might "DISABLE=True" be found on a switch with ...
1 commentQuestion 7: The VXLAN spec allows for two implementation types. One uses...
Question 8: What is the first command necessary when configuring SSH aft...
Question 9: How many Virtual Network Identifiers are supported by the VX...
Question 10: Which of the following Tap Aggregation command sessions are ...
Question 11: Given the following output, which of the following have you ...
1 commentQuestion 12: Which command below is valid to use as a way to verify the s...
Question 13: When using Monitor Sessions with a destination of the CPU, i...
Question 14: What does LANZ do?
Question 15: Which of the following is not a DANZ feature?...
Question 16: What is the packet overhead for a VXLAN-encapsulated frame?...
Question 17: Which of the following EOS features might alleviate the need...
Question 18: Which of the following statements is false?...
Question 19: Many Arista switches support reversible air flow. When the f...
Question 20: What Arista feature helps with the diagnosis of microburstin...
1 commentQuestion 21: Which of the following statements is true with an Arista swi...
Question 22: Which of the following Arista switch series' supports Zero T...
Question 23: What is the name of the feature that allows the destination ...
Question 24: Which of the following interface types are never found on an...
Question 25: What is the name of the Arista EOS feature that allows you t...
Question 26: Which of the following statuses will be displayed when VMTra...
2 commentQuestion 27: On EOS 4.15 and above, the ability to show JSON output for E...
Question 28: True or False: When configured as an MLAG domain, the Arista...
Question 29: What is the name of the feature that allows you to retrieve ...
Question 30: What is the name of the link that connects two Arista switch...
1 commentQuestion 31: On what protocol is Multi-Switch CLI based?...
Question 32: What is the MLAG peer address?
Question 33: When an Arista switch boots with no startup-config and ZTP e...
Question 34: Why is FastCli faster than Cli?...
Question 35: When you fullrecover a switch from Aboot and a USB drive is ...
Question 36: True or False: When ZTP has been placed in cancel mode, you ...
Question 37: Arista switches automatically issue a show tech support once...
Question 38: If an agent were to suffer a catastrophic failure and die, w...
1 commentQuestion 39: What is the command to set the switch to use EOS 4.15.1F.swi...
Question 40: What command configuration mode enabled you to connect to an...
Question 41: After configuration and enabling XMPP, what command can be u...
Question 42: How might you filter the output from the show interfaces cou...
Question 43: If you create a schedule job named "Colleen-Job", where will...
Question 44: On EOS 4.13.1F, which of the following statements are true i...
Question 45: What is the default spanning-tree mode on an Arista switch?...
Question 46: If you were build a large-scale cloud-based architecture tha...
Question 47: Which of the following commands will show the mac-address to...
Question 48: Which of the following commands is being deprecated and will...
1 commentQuestion 49: On an Arista switch, which port is used to connect a laptop ...
Question 50: How does Arista's VMTracer feature support multi-tenancy?...
Question 51: What does %1 signify when writing an alias statement in CLI?...
1 commentQuestion 52: On what interface(s) will ZTP send out requests?...
Question 53: With VXLAN, a table is created that contains all the known V...
Question 54: What is the fundamental purpose of SysDB?...
Question 55: What would be the result of issuing a reload command on one ...
Question 56: On an Arista switch, what is the default username and passwo...
Question 57: Which of the following are valid Event Manager triggers?...
Question 58: Which of the following commands will show all of the hardwar...
Question 59: Which of the following Arista switches support LANZ?...
Question 60: When configuring MLAG, Arista recommends that the trunk grou...
Question 61: How many line card slots are reserved for supervisors on the...
Question 62: Given the following output, on what interface would you expe...
Question 63: Which command will successfully configure Ethernet5 to be 40...
Question 64: Which of the following are not valid boot-config file entrie...
Question 65: The Arista MLAG domain ID is:
Question 66: How many Arista switches may be a part of a single MLAG doma...
Question 67: In EOS, which of the following statements is the shortest ac...
Question 68: Which of the following statements are true?...
Question 69: What is Adaptive Segmentation?
Question 70: How is LANZ enabled on switches that support it?...
Question 71: Which command will disable Adaptive Segmentation in VMTracer...
Question 72: Which of the following commands can you use to see which EOS...
Question 73: Where does SysDB store its contents when the switch reboots?...
Question 74: Where does Aboot look for the boot system image at boot time...
Question 75: What will the following command do? show event-monitor arp |...
Question 76: Which Arista switch series supports more than eight line car...
Question 77: When ZTP is in enable node, what triggers ZTP when the switc...
1 commentQuestion 78: Given the following output, what can you determine about Eth...
Question 79: Complete this sentence: In an Arista MLAG configuration, int...
Question 80: Which of the following are valid interface named in EOS? (Se...
Question 81: What is the EOS feature that allows switches with Multi-Swit...
Question 82: Which of the following programming environments is included ...
Question 83: What does the asterisk in the following output signify? (Exh...
Question 84: What is Aboot?
Question 85: To upgrade the EOS running on an Arista switch, which of the...
Question 86: Arista MLAG uses which of the following protocols for inter-...
Question 87: Which of the following best describes Arista's MLAG feature?...
Question 88: What service does the MLAG feature provide?...
Question 89: ZTP can retrieve either an EOS configuration file or a scrip...
Question 90: What must be active on the VMware side in order for EOS to h...
Question 91: What is required in order for Multi-Switch CLI to be impleme...
Question 92: On an Arista 7150-24, which of the following commands would ...
Question 93: Does Arista EOS firmware support U.S. Federal Information Pr...