CRE Exam Dumps | A substantial fraction of the usual design effort need NOT be devoted to a reliability program.: Response:

<< Prev Question Next Question >>

Question 49/170

A substantial fraction of the usual design effort need NOT be devoted to a reliability program.:
Response:

A. When time is limited.

B. When the equipment is complex.

C. When high reliability is specified.

D. When high reliability is not specified.

Question List (170q): Question 1: Which of the following graphs represents a product that is u...; Question 2: Specifically, up-time ratio is a measure of: Response:...; Question 3: Given mean-time-to-failure of 200 hours for each of two comp...; Question 4: Failure modes and effects analysis involves what activity? R...; Question 5: Which answer correctly describes the experimental design on ...; Question 6: All of the following Boolean algebra expression is incorrect...; Question 7: If a company monitors field reliability using both 6 and 12 ...; Question 8: A reliability test was terminated after 171 hours based upon...; Question 9: Which of the following BEST describe a critical item in reli...; Question 10: FMECA is: Response:; Question 11: The distribution used to describe the time between failures ...; Question 12: Design reviews should have sufficient information available ...; Question 13: Which process has as its principle parts - Defining the syst...; Question 14: A QFD team's primary goal should be to Response:...; Question 15: When a large number of components have been tested for a fix...; Question 16: When reliability people say they are breaking the monopoly o...; Question 17: If a component has a known constant failure rate of 0.0037 f...; Question 18: Data collection for a failure reporting, analysis, and corre...; Question 19: A go/no-go device is tested until it fails. If X is the numb...; Question 20: Derating a component to 50 percent of its operating value wi...; Question 21: Which of the following CANNOT be classified as a computer ou...; Question 22: A system is defined by the following reliability block diagr...; Question 23: The success of the FMEA is principally dependent on: I. Good...; Question 24: What is this system's reliability at 700 hours? Component fa...; Question 25: If the average repair time for a system is 3 hours and the M...; Question 26: A data collection, analysis, and reporting system should: I....; Question 27: A "fail-safe" requirement means: Response:...; Question 28: An air handling system has a MTBF of 8000 hours, MTBMct of 1...; Question 29: The "least squares" description in regression analysis perta...; Question 30: What is the probability of exactly 3 defects given the follo...; Question 31: A reliability test conducted during the pre-production stage...; Question 32: For continual improvement in product reliability which of th...; Question 33: Measures of availability include: I. Effectiveness. II. Inhe...; Question 34: The purpose of a failure reporting, analysis and corrective ...; Question 35: Maintainability can be improved by: Response:...; Question 36: The term "failure mode" is defined as the: Response:...; Question 37: Which of the following is a primary concern for a reliabilit...; Question 38: A component has a strength of 8000 psi and a standard deviat...; Question 39: Which of the following is the BEST approach to recover produ...; Question 40: If the probability of a car starting on a sub-zero morning i...; Question 41: In the House of Quality, the principal matrix shows the rela...; Question 42: Which of the following is the BEST example of a random varia...; Question 43: Which of the following is a basic element in the corrective ...; Question 44: When a bathtub curve is used, one characteristic of the flat...; Question 45: Which of the following FTA statements is NOT true? Response:...; Question 46: An undesired event in a system led to the below fault tree. ...; Question 47: Ideally for a FRACAS to be effective, how many failures shou...; Question 48: Total system effectiveness can be predicted during the conce...; Question 49: A substantial fraction of the usual design effort need NOT b...; Question 50: If the exponential distribution is assumed, what is the reli...; Question 51: Root cause failure analysis is necessary to identify and cor...; Question 52: Product safety is a concern in today's environment. If a ris...; Question 53: For the exponential model, the reliability at mean time to f...; Question 54: The reliability of a device comprised of various parts funct...; Question 55: For single-failure modes, the probability plotting methods u...; Question 56: Which one of the following quantitative methods does NOT app...; Question 57: The first phase in the operation life history of a populatio...; Question 58: Censoring of reliability data indicates which of the followi...; Question 59: Which of the following is a continuous probability distribut...; Question 60: A mission profile is: I. Time-phased. II. A summary of event...; Question 61: A component fails on the average of once every 4 years with ...; Question 62: Which of the following is the key component in continuously ...; Question 63: For equal length missions an increase in the MTBF will yield...; Question 64: In an analysis of variance, which of the following distribut...; Question 65: What is meant by "derating"? I. The technique of using a par...; Question 66: Inherent reliability can be increased by: Response:...; Question 67: Censoring of data occurs when Response:...; Question 68: A key distinction between Taguchi designed experiments and c...; Question 69: Which of the following techniques is NOT used when derating ...; Question 70: A device has a MTBF of 400 hours. Assuming an exponential di...; Question 71: For human factors testing, the reliability engineer should u...; Question 72: Probability ratio sequential tests are used for products des...; Question 73: Software reliability planning includes all of the following ...; Question 74: Internal testing sources of component reliability data are: ...; Question 75: Which one of the following would NOT be necessary in a corre...; Question 76: When performing trade-offs in evaluating parts for reliabili...; Question 77: Using complete field-based data, a reliability engineer has ...; Question 78: A certain equipment has a MTBF of m = 300 hours. Assuming an...; Question 79: The reliability manager or engineer attend and participate i...; Question 80: A sample is split into subgroups. Testing for each subgroup ...; Question 81: Which of the following are the MOST desirable basic skills r...; Question 82: Basic sources of reliability data are: I. In-plant testing. ...; Question 83: Which of the following is the MOST effective technique for p...; Question 84: The BEST way to set an overall reliability goal is to: Respo...; Question 85: An exclusive "or" gate produces an output only if: Response:...; Question 86: All of the following statements concerning statistical infer...; Question 87: What is the reliability of the logic diagram to the below? (...; Question 88: Which of the following tools are classified as structured ro...; Question 89: It is reliability's job to see that all the tasks outlined i...; Question 90: A person takes their car to the repair shop and it stops doi...; Question 91: Which of following is NOT elements of risk priority number f...; Question 92: When parts are selected for a product in development, which ...; Question 93: Which of the following statistical distributions can be used...; Question 94: Highly repetitive operations should be assigned to: Response...; Question 95: Develop the fault tree analysis for a candy dispensing machi...; Question 96: If the plating time of a tube increases as the inside diamet...; Question 97: A component has a constant failure rate of 0.0005 failures p...; Question 98: A fault tree analysis (FTA) is a design analysis technique c...; Question 99: A design review committee has recommended changes to a propo...; Question 100: Which of the following is TRUE about hypothesis testing? Res...; Question 101: Which of the following are important elements of the concept...; Question 102: What is the difference between a system whose reliability pr...; Question 103: Customer feedback and data have been gathered on several new...; Question 104: Which of the following is the MOST appropriate reason for se...; Question 105: Laboratory tests of a new polymer prototype yielded the foll...; Question 106: Which of the following is best defined as the practice of us...; Question 107: What is the general use of an R chart? Response:...; Question 108: Which answer BEST describes the events and operating conditi...; Question 109: Which of the following techniques is MOST efficient when two...; Question 110: The use of plug-in devices improves all of the following EXC...; Question 111: Which of the following forms of reliability data will BEST p...; Question 112: Which of the following action will help eliminate the effect...; Question 113: A 2 level 5 factor experiment is being conducted to optimize...; Question 114: What functions can normally be expected to be assigned to th...; Question 115: In general, consumer consider reliability and safety to be a...; Question 116: What is meant by reliability assurance? I. The probability o...; Question 117: The probability of an accident for the head event "H" given ...; Question 118: Which mathematical model is characterized by linking exact r...; Question 119: Maintainability is: Response:; Question 120: A company is in a multi-products, competitive market. Which ...; Question 121: The maintenance action rate (MAR) may be mandated by contrac...; Question 122: Maintenance times on simple with straightforward repair will...; Question 123: Reliability prediction is: Response:...; Question 124: When a new system is being developed, which of the following...; Question 125: A prototype lot of a new design suspension spring underwent ...; Question 126: What is this system's reliability at 3000 hours? MTBFs for t...; Question 127: According to the Reliability Analysis Center, which of the f...; Question 128: What is the MOST important role performed by a failure revie...; Question 129: What is the MOST accurate method to verify that the maintain...; Question 130: Top probability of the top event is represented by which of ...; Question 131: Time-to-market can be reduced MOST directly through the use ...; Question 132: For the ANOVA Table below, what is the Fcal statistic? (Exhi...; Question 133: System-safety analytical techniques include all EXCEPT: Resp...; Question 134: Reliability Growth is: I. Often mathematically modeled with ...; Question 135: The function below has a density distribution where X is a c...; Question 136: From a company's point of view, which of the following costs...; Question 137: Which of the following provides the maximum benefit of parts...; Question 138: Pascal's triangle presents a simple means of determining whi...; Question 139: There is a subtle difference between a standard parts progra...; Question 140: All of the following statements are TRUE about confidence in...; Question 141: Experimental design plans usually call for testing a number ...; Question 142: In standby parallel systems, imperfect switching means : I. ...; Question 143: Which of the following is NOT true about the Taguchi DOE app...; Question 144: A failure that leaves the system fully functional is: Respon...; Question 145: Which of the following is an appropriate use for experimenta...; Question 146: Human factors in product safety planning are assessed for wh...; Question 147: The means of large samples from a population tend to be norm...; Question 148: Consider the four normal stress and strength distributions d...; Question 149: Random sampling plans are based on which of the following as...; Question 150: Maintainability considerations are important in the design o...; Question 151: According to the definition of reliability, performance, ove...; Question 152: A satellite has two redundant control systems, each has a fa...; Question 153: A Reliability Engineering Department is conducting a trainin...; Question 154: What type of failure is usually reduced by periodic overhaul...; Question 155: As a result of improper machining, a gear-tooth in a vehicle...; Question 156: In a software development project, which of the following el...; Question 157: Corrective maintenance is performed in order to Response:...; Question 158: Certain functional tests can be conducted for electronic equ...; Question 159: The House of Quality incorporates a correlation matrix roof....; Question 160: The department having the authority to sign all deviations p...; Question 161: All of the following are purposes of a production reliabilit...; Question 162: When designing experiments, which term describes the situati...; Question 163: The two principal measures of failure during risk assessment...; Question 164: Risk management includes which of the following? I. Integrat...; Question 165: Product residual safety risk includes which two of the follo...; Question 166: The distribution used to describe the time between failures ...; Question 167: If the reliability goal for a 4 - hour mission is 0.9999 for...; Question 168: Which of the following techniques is MOST beneficial in trac...; Question 169: Product safety standards do NOT include: Response:...; Question 170: What is the Z value needed to conduct a two tail test in a s...

Question 49/170

LEAVE A REPLY

Download PDF File