API-936 Exam Dumps | For linings that use a surface layer of refractory plastic or a ramming mix, when should trimming, jointing,

Home
API
Refractory Personnel
API.API-936.v2025-12-16.q38
Question 30

Valid API-936 Dumps shared by EduDump.com for Helping Passing API-936 Exam! EduDump.com now offer the newest API-936 exam dumps, the EduDump.com API-936 exam questions have been updated and answers have been corrected get the newest EduDump.com API-936 dumps with Test Engine here:

Access API-936 Dumps Premium Version
(87 Q&As Dumps, 35%OFF Special Discount Code: freecram)

<< Prev Question Next Question >>

Question 30/38

For linings that use a surface layer of refractory plastic or a ramming mix, when should trimming, jointing, and venting be done?

A. After water curing for 24 hours

B. Before stopping work for the day or shift

C. Never; these steps are not required when refractory plastics or ramming mixes are used

D. After the entire installation is complete

Correct Answer: B

When using refractory plastics or ramming mixes, it is critical thattrimming, jointing, and venting be performed before stopping work for the day or shift. API 936 and TR 980 specify that proper surface preparation helps relieve vapor pressure during dryout and prevents cracking. If these steps are postponed, the surface may dry unevenly or set improperly, complicating the subsequent installation and reducing bond quality between layers.
Venting paths are particularly important in thick plastic or ramming layers where moisture may be trapped, and jointing ensures layer-to-layer continuity. Trimming also smooths out inconsistencies and aligns the lining to specifications.
Reference:
API TR 980 - Section "Refractory Plastics and Ramming Mixes: Trimming, Jointing, and Venting" requires these actions be doneprior to any interruptionof installation work.

Your email address will not be published. Required fields are marked *

Comment: *

Name: *

Email: *

Rating: *

Verification: *

Question List (38q): Question 1: As-installed gunned test specimens are prepared by cutting s...; Question 2: Which of the following is a correct condition for gunned mat...; Question 3: Test results received from cast sample mock-ups will serve t...; Question 4: Plastic refractories with a workability index below the manu...; Question 5: Which of the following does not apply to cold crushing stren...; Question 6: If the refractory lining is required before pressure testing...; Question 7: Maximum allowable crack length, visible on the surface of a ...; Question 8: Newly applied cast linings must cure before stripping the fo...; Question 9: During gunning, inclusion of rebound is minimized by which o...; Question 10: A pigment shall be used in the curing compound in order to:...; Question 11: Who is responsible for the accuracy of installation records?...; Question 12: Which of the following steps are required to apply to thin-l...; Question 13: What characteristic shall be required for form selection?...; Question 14: What abrading media is required in the ASTM C-704 abrasion-r...; Question 15: Abrasion resistance of a material is reported as loss of:...; Question 16: Which of the following conditions must be met for test resul...; Question 17: For non-erosive service, what is the required number of test...; Question 18: Which of the following is the inspector responsible for?...; Question 19: An alternative to wire mesh baskets is a panel with enclosed...; Question 20: The quantity of manufactured refractory that has the same fo...; Question 21: Throughout a period of at least 24 hours, test specimens for...; Question 22: The vessel in which the cracking reaction occurs or is compl...; Question 23: For qualification testing, test panels for pneumatic gunning...; Question 24: What is the ASTM test designation for cold crush strength?...; Question 25: From each production run, the testing frequency for erosion ...; Question 26: A layer coat of refractory lining that is applied to an exis...; Question 27: Which of the following statements regarding curing of hydrau...; Question 28: Equipment used during applicator qualification testing shall...; Question 29: In the absence of owner specification, which party or indivi...; Question 30: For linings that use a surface layer of refractory plastic o...; Question 31: Which of the following is a longitudinally hinged anchoring ...; Question 32: Ceramic fiber batten strips shall be:...; Question 33: The term "shelf life" refers to the maximum time:...; Question 34: Which of the following is a quality control element? (This m...; Question 35: Apparent porosity values are reported as:...; Question 36: A change in the length of a specimen measured before and aft...; Question 37: Cold wall refractory lined components shall be dried out by ...; Question 38: Testing to verify that the application equipment and personn...

[×]

Download PDF File

Enter your email address to download API.API-936.v2025-12-16.q38.pdf

Email:

Disclaimer:
Freecram doesn't offer Real GIAC Exam Questions. Freecram doesn't offer Real SAP Exam Questions. Freecram doesn't offer Real (ISC)² Exam Questions. Freecram doesn't offer Real CompTIA Exam Questions. Freecram doesn't offer Real Microsoft Exam Questions.
Oracle and Java are registered trademarks of Oracle and/or its affiliates.
Freecram material do not contain actual actual Oracle Exam Questions or material.
Microsoft®, Azure®, Windows®, Windows Vista®, and the Windows logo are registered trademarks of Microsoft Corporation.
Freecram Materials do not contain actual questions and answers from Cisco's Certification Exams. The brand Cisco is a registered trademark of CISCO, Inc.
CFA Institute does not endorse, promote or warrant the accuracy or quality of these questions. CFA® and Chartered Financial Analyst® are registered trademarks owned by CFA Institute.
Freecram does not offer exam dumps or questions from actual exams. We offer learning material and practice tests created by subject matter experts to assist and help learners prepare for those exams. All certification brands used on the website are owned by the respective brand owners. Freecram does not own or claim any ownership on any of the brands.

Question 30/38

LEAVE A REPLY

Download PDF File