<< Prev Question Next Question >>

Question 31/72

For a typical inspection program, if excessive inspection is applied then,

LEAVE A REPLY

Your email address will not be published. Required fields are marked *

Question List (72q)
Question 1: Results of quantitative consequence analysis are usually exp...
Question 2: Following are the common mechanical deterioration mechanisms...
Question 3: If a QRA has been prepared for a process unit, the analysis ...
Question 4: The risk prior to mitigation activities...
Question 5: ____________ are often necessary to establish susceptibility...
Question 6: Who can provide useful input (such as the spectrum of proces...
Question 7: ______________ provides a consistent methodology for assessi...
Question 8: Small hole, crack or rupture are examples of...
Question 9: Other functional failures are usually covered within...
Question 10: FILL BLANK RP 580 significantly targeted at the application ...
Question 11: Occurrence of a particular set of circumstances, is called a...
Question 12: A process to assess risks, to determine if risk reduction is...
Question 13: When some risk identified as acceptable then one of the foll...
Question 14: Act of mitigating a known risk to a lower level of risk....
Question 15: Outcome of an event
Question 16: ____________deals with total risk than with risk involve onl...
Question 17: Results from quantitative analysis logic models are validate...
Question 18: Deterioration rates can be expressed in terms of...
Question 19: FILL BLANK RP 580 is intended to promote consistency and qua...
Question 20: FILL BLANK RBI as an integrated management tool that complem...
Question 21: A RBI analysis shares many of the techniques and data requir...
1 commentQuestion 22: Through __________________, inspection activities are focuse...
2 commentQuestion 23: __________ is not a substitute for a process hazards analysi...
Question 24: Damage mechanisms where deterioration rates are immeasurable...
Question 25: The program that is focused on understanding failure modes, ...
Question 26: The reduction in the ability of a component to provide its i...
Question 27: Following are the critical variables for deterioration mecha...
Question 28: Sec occurs when equipment is exposed to environments...
Question 29: The type of failure mode that likely to occur due thinning...
Question 30: Qualitative consequence analysis of failure can be estimated...
Question 31: For a typical inspection program, if excessive inspection is...
Question 32: Following is the unit of measure of consequence that is leas...
Question 33: An analytical tool that organizes and characterizes potentia...
Question 34: Toxic releases in RBI are only addressed when they affect...
Question 35: _____________ represents the next generation of inspection a...
Question 36: RBI requires the commitment and cooperation of the...
Question 37: Probability side of the risk equation is normally managed by...
Question 38: The type of failure mode that likely to occur due to SSC...
Question 39: Termination of the ability of a system, structure, or compon...
Question 40: A physical condition or a release of a hazardous material th...
Question 41: The following types of pressurized equipment and associated ...
Question 42: When in accurate or insufficient failure data exists on the ...
Question 43: The suitability and current condition of the equipment withi...
Question 44: In process plants are established to detect and evaluate det...
Question 45: Hazard identification in a RBI analysis generally focuses on...
Question 46: Risk presented in quantitative risk analysis as a...
Question 47: Following will cover the functional failures except...
Question 48: Consequence analysis will aid in preparation of...
Question 49: RBI is focused on a systematic determination of...
Question 50: Risk presented in qualitative risk analysis as...
Question 51: The amount and type of codes and standards used by a facilit...
1 commentQuestion 52: Act of mitigating a known risk to a lower level of risk....
Question 53: The RBI program for environmental consequences, typically fo...
Question 54: The type of failure mode that likely to occur due to pitting...
Question 55: When equipment has low deterioration rates as an inspector w...
1 commentQuestion 56: The primary audience for RP 580 is...
Question 57: _________ are the primary inputs into the probability of fai...
Question 58: FILL BLANK _________ produces inspection and maintenance pla...
Question 59: In most consequence evaluations, a key element in deter-mini...
Question 60: The risk assessment programme which focuses on process unit ...
1 commentQuestion 61: The event may be
Question 62: Consequence is always __________ for safety aspects...
Question 63: If multiple inspections have been performed, which inspectio...
Question 64: The ability to state the rate of deterioration precisely is ...
Question 65: Is key to performing deterioration mechanism identification...
1 commentQuestion 66: Limitation of any negative consequence or reduction in proba...
Question 67: The programme that focused on maintaining the mechanical int...
Question 68: Who should be consulted to define the equipment deterioratio...
Question 69: The data validation step stresses the need for a knowledgeab...
Question 70: Depending on the methodology employed in qualitative analysi...
Question 71: _________________curves are referred for the deterioration m...
Question 72: Following are not the residual risk factors for loss of cont...