Valid H31-311_V2.5 Dumps shared by ExamDiscuss.com for Helping Passing H31-311_V2.5 Exam! ExamDiscuss.com now offer the newest H31-311_V2.5 exam dumps, the ExamDiscuss.com H31-311_V2.5 exam questions have been updated and answers have been corrected get the newest ExamDiscuss.com H31-311_V2.5 dumps with Test Engine here:

Access H31-311_V2.5 Dumps Premium Version
(750 Q&As Dumps, 35%OFF Special Discount Code: freecram)

Online Access Free H31-311_V2.5 Exam Questions

Exam Code:H31-311_V2.5
Exam Name:HCIA-Transmission V2.5
Certification Provider:Huawei
Free Question Number:336
Version:v2025-01-18
Rating:
# of views:242
# of Questions views:14870
Go To H31-311_V2.5 Questions

LEAVE A REPLY

Your email address will not be published. Required fields are marked *

Other Version
218 viewsHuawei.H31-311_V2.5.v2024-08-26.q89
650 viewsHuawei.H31-311_V2.5.v2022-07-25.q77
Exam Question List
Question 1: The backplane has two -48V power lines, and each board obta...
Question 2: Which of the following communication protocols does Huawei e...
Question 3: Which of the following is the step for China to multiplex 2...
Question 4: Which of the following statements about the frame structure ...
Question 5: TNG 1N401 board supports mixed transmission of multiple ODUk...
Question 6: Which of the following descriptions about the MD02 board is...
Question 7: When configuring the OSN3500 with SXCS boards, which of the...
Question 8: Among the following modulation technologies, which one perf...
Question 9: Which of the following is a functional unit that provides h...
Question 10: The dispersion coefficient is the time delay difference cau...
Question 11: Multicast forwarding can be understood as selective broadca...
Question 12: Regarding the AU-AIS alarm, which of the following statemen...
Question 13: When the U2000 is synchronized, the NE data that is the sam...
Question 14: Which of the following device domains can be managed by U200...
Question 15: OL board, OLA board and OPC board can all amplify optical si...
Question 16: Which of the following options are considered to be deficie...
Question 17: Users can easily access NCE through a browser without havin...
Question 18: Which of the following statements about 1+1 protection of c...
Question 19: PDM uses a polarization beam splitter to split the laser int...
Question 20: In the OLT+ONU combined networking mode, OLT mainly plays t...
Question 21: Are the following statements about the definition of SDH co...
Question 22: Which of the following options are low-loss areas of single-...
Question 23: PWE3 is a Layer 2 service bearer technology that can simulat...
Question 24: In Huawei's T-SDN network architecture, () realizes central...
Question 25: Which of the following descriptions are correct? (Multiple c...
Question 26: Which of the following descriptions of MPLS are wrong? (Mult...
Question 27: For a (local) HA solution where the active and standby serve...
Question 28: From the formula: OTUk rate = 255/(39-k) × STM-N rate, we c...
Question 29: Sending test frames will affect normal business....
Question 30: When the low-level resources of the device are insufficient,...
Question 31: What are the advantages of ESC? (Multiple choice)...
Question 32: Which of the following modulation technologies is currently...
Question 33: Which of the following technologies is the main difference b...
Question 34: Fiber amplifiers can be divided into rare earth ion doped f...
Question 35: Which of the following descriptions about solving the system...
Question 36: Which of the following statements about OTM-nm and OTM-nr.m...
Question 37: Two beams of light that meet the coherence condition are ca...
Question 38: The frame structure of OTUk at each level is the same....
Question 39: Physical port: also known as MAC port, which is the externa...
Question 40: Which of the following is a VLAN classification method? (Mul...
Question 41: For ODUk SNCP protection, if the pass-through site is an el...
Question 42: Which of the following options are low-loss areas of single-...
Question 43: MS-AIS and MS-RDI belong to a group of warning information, ...
Question 44: Compared with PDH, the main advantages of SDH are reflected...
Question 45: Which of the following alarms will not trigger an AU-AIS ala...
Question 46: Which of the following elements does a data communication n...
Question 47: Which of the following is a functional unit that provides se...
Question 48: Which of the following descriptions about the PANEL panel o...
Question 49: Which unit is newly added in Liquid OTN?...
Question 50: What does the optical layer overhead include? (Multiple choi...
Question 51: Which of the following bytes in the regenerator section over...
Question 52: Which of the following factors determine that the optical s...
Question 53: The receiving end performs BIP-8 check on the received STM-...
Question 54: Which of the following logic function blocks is used to proc...
Question 55: Which of the following is not an advantage of WDM?...
Question 56: Which of the following are not passive optical devices? (Mul...
Question 57: Which of the following is the main advantage of SDH? (Multip...
Question 58: When using scripts to back up and restore the network confi...
Question 59: When 2M PDH signal is mapped into VC12, the mapping method ...
Question 60: Which of the following options are included in the alarm lev...
Question 61: Which of the following is correct about the difference betwe...
Question 62: U2000 client can be installed on Windows, Solaris and SUSE L...
Question 63: The difference between ASON network and ordinary network is ...
Question 64: RSOH, MSOH, HPOH and LPOH implement monitoring functions in...
Question 65: SDH signals must be scrambled before transmission over optic...
Question 66: From the following barcode 02846710HC000085 Y1 LPS-FRM800-P...
Question 67: Which of the following is the multiplexing method of SDH?...
Question 68: The speed of SF64 and SL64 boards are both STM-64. Therefore...
Question 69: OTM nr.m consists of a maximum of "n" optical multiplexed ch...
Question 70: 1000BaseSX uses single-mode optical fiber and light with a w...
Question 71: Which of the following correctly describes the order in whic...
Question 72: The single-fiber bidirectional wavelength division multiple...
Question 73: The information payload area stores only the information pa...
Question 74: MSTP (Multi-Service Transport Platform) is a multi-service ...
Question 75: Which of the following are the logical function modules inv...
Question 76: Which of the following reasons will not cause the network m...
Question 77: Which of the following are device-level protection solutions...
Question 78: Which of the following alarms will not generate correspondi...
Question 79: Which of the following options are the main characteristics...
Question 80: Which of the following are components of a WDM system that m...
Question 81: Nonlinear effects are closely related to optical power. To ...
Question 82: Which of the following statements about U2000 licenses is wr...
Question 83: The 1310nm and 1550nm transmission windows are low-loss win...
Question 84: 1:N linear multiplex section protection: when the working c...
Question 85: After configuring PDH services on a per-network element basi...
Question 86: In the SDH optical synchronous transmission system, which o...
Question 87: Which of the following networking types is optical line pro...
Question 88: Frame-Mapped GFP (GFP-F) is a processing mode for data encod...
Question 89: For Huawei equipment, NODE ID is the unique identifier of t...
Question 90: There are three types of multi-level connection monitoring ...
Question 91: Which of the following is the common point between the two-...
Question 92: Regarding the comparison between Raman amplifier and EDFA, ...
Question 93: Which of the following descriptions of OTM-nm and OTM-nr.m o...
Question 94: U2000 network management supports multiple external interfac...
Question 95: OTN has its own unique frame structure and rich overheads to...
Question 96: OLT is connected to the switch through () and uses the V5.2 ...
Question 97: The clock unit can only access the external clock source as...
Question 98: The subnet mask of 255.255.255.248, according to the calcul...
Question 99: In the Colored & Directed scenario of 4D ROADM, how man...
Question 100: In WDM systems, the reduction in optical signal-to-noise ra...
Question 101: Pointer adjustment is related to which of the following?...
Question 102: The last 256 columns in the OTN frame structure are the FEC ...
Question 103: Ethernet service OAM focuses on the maintenance of end-to-e...
Question 104: In actual wavelength division systems, systems with rates o...
Question 105: Which of the following methods are included in WDM networkin...
Question 106: MPLS label allocation is divided into static allocation and ...
Question 107: What kind of cascading method does the EoS board of OptiX OS...
Question 108: EPL services use ports and bandwidth exclusively, and differ...
Question 109: If a network port that supports auto-negotiation is connect...
Question 110: PWE3 is a processing mechanism that simulates the key attri...
Question 111: STM-N signals must be scrambled when transmitted on the line...
Question 112: Which of the following is not a northbound interface provide...
Question 113: Which new unit is added to Liquid OTN?...
Question 114: What is the first condition that a network needs to have in...
Question 115: Which of the following is not an advantage of Raman amplifie...
Question 116: OTN technology is developed based on SDH and WDM technology,...
Question 117: The rate represented by STM-1 is ()....
Question 118: The EDFA inside the THBIDAP board has the () function. When ...
Question 119: Which of the following statements is wrong?...
Question 120: Communication networks can be divided into local area netwo...
Question 121: Which of the following options does not belong to the applic...
Question 122: Which of the following is the switching point of linear mult...
Question 123: Compared with traditional SDH and SONET equipment, OTN has ...
Question 124: What client-side service signals does the TNG1T401 board sup...
Question 125: The primary and backup ports of the linear multiplexing seg...
Question 126: () is a parameter used to describe the reliability of the tr...
Question 127: Compared with traditional SDH and SONET equipment, which of...
Question 128: LCK insertion takes precedence over AIS insertion. That is,...
Question 129: Which of the following options belong to the functions in th...
Question 130: If a weak signal light and a strong pump light are transmit...
Question 131: U2000 can flexibly interconnect with different third-party n...
Question 132: EPL service uses the bandwidth on the line exclusively, whi...
Question 133: How many frames is the minimum interval between two adjacent...
Question 134: What is the frame structure of STM-16?...
Question 135: Compared with the dense wavelength division multiplexing sy...
Question 136: A bidirectional ring means that the routes for sending and ...
Question 137: NCE's software deployment method adopts B/S (Browser/Server)...
Question 138: The LOI low-level interface includes multiple logical functi...
Question 139: STM-64 has () AU pointer.
Question 140: The frame structure of TU3 is a bit incomplete, and the gap ...
Question 141: Which of the following values has the highest clock quality...
Question 142: In a wavelength division multiplexing system, when the numb...
Question 143: FAS is the frame alignment overhead with a length of 6 bytes...
Question 144: Consider an optical fiber as a "multi-lane" public road. Th...
Question 145: () is called optical transmission segment in Chinese, and (...
Question 146: A subnet can contain other subnets....
Question 147: If the virtual cascade group at one end of the equipment ha...
Question 148: VLAN domain can isolate unicast messages of different users...
Question 149: The most effective subnet mask in a point-to-point WAN link ...
Question 150: Two beams of light that meet the coherence condition are ca...
Question 151: Which of the following alarms will definitely trigger optica...
Question 152: The essence of OPSK modulation is to reduce the baud rate o...
Question 153: Which of the following descriptions of ODUK_PM_BDI is correc...
Question 154: The current sparse wavelength division multiplexing system ...
Question 155: Which of the following descriptions about the slot settings ...
Question 156: Compared with traditional WDM, which of the following optio...
Question 157: What principle of light is used when light propagates in opt...
Question 158: SES: There are 5% or more error blocks or at least one defe...
Question 159: Which of the following statements are correct regarding the ...
Question 160: Ethernet_II and IEEE802.3 frame types are distinguished by ...
Question 161: Which of the following descriptions about signal marker byt...
Question 162: Which of the following is protected by the channel protectio...
Question 163: In the Windows operating system, the U2000 program's own lo...
Question 164: For OSN3500, which of the following boards provides central...
Question 165: FOADM includes parallel FOADM and serial FOADM, both of whic...
Question 166: Which of the following is not an advantage of using QinQ tec...
Question 167: Which subtype of tributary SNCP protection requires no elec...
Question 168: Arrayed Guided Grating (AWG) multiplexer/demultiplexer has t...
Question 169: Manual configuration will clear the data on the NE side....
Question 170: Which of the following planes does the ASON network have mor...
Question 171: The 48 wave OTM site needs to be equipped with an OAU ampli...
Question 172: The value range of U-PTR is 0~782. When the receiving end re...
Question 173: Which of the following site types support business up and d...
Question 174: The management scope of O MSn is the path from the input op...
Question 175: In a wavelength division system, after a certain distance o...
Question 176: When BIP-8 in the OTUk segment monitoring overhead SM detect...
Question 177: The segment overhead of STM-16 is 9*8*16 bytes/frame....
Question 178: The segment overhead of STM-4 is 9+9+4 lines/frame....
Question 179: HUB is a multi-port repeater. When HUB is the central device...
Question 180: Which of the following service nodes can be connected via a...
Question 181: In the network management system, the network element perfo...
Question 182: MPLS is a label forwarding technology. Which of the followin...
Question 183: E1 has three modes: framing, multi-framing and unframing. Th...
Question 184: Which of the following is the adjustment unit of AU-PTR?...
Question 185: The optical amplifier unit can compensate for line loss and...
Question 186: By default, a B2-EXC alarm is reported when the number of B...
Question 187: Both PDH and SDH have globally unified standards....
Question 188: In the electric power dispatching system, dispatching data ...
Question 189: What functions does the SDH overhead byte perform? (Multiple...
Question 190: The nominal rate of the OTU4 signal is 111809973.568 kbits,...
Question 191: Which of the following statements about the MSP ring are cor...
Question 192: In the OTN mapping path, the ODUk signal can only be obtain...
Question 193: In case of SNCP, the line board selectively receives the se...
Question 194: How many 2M business work boards does OSN 7500 support at mo...
Question 195: Linear MSP (LMSP) has two modes: 1+1 and 1:1. Additional se...
Question 196: The two PIU/APIU boards of the OptiXtrans E6616 or E6608 (0...
Question 197: AAC address consists of 46 bits and is globally unique. Whic...
Question 198: Which of the following databases is used by U2000 on PC/WIN2...
Question 199: Which of the following are the basic functions of U2000? (Mu...
Question 200: Which of the following bytes can be used for wired calls bet...
Question 201: The technology of using a local oscillator laser of the sam...
Question 202: In the integrated DWDM system, the transmitting light sourc...
Question 203: Which of the following options does the 802.1Q tag header c...
Question 204: In terms of protection capability, which of the following t...
Question 205: Which type of board does TQM belong to?...
Question 206: User management can ensure the security of user information...
Question 207: The OTN electrical layer SM, PM, and TCMi overheads all con...
Question 208: U2000 provides physical view, Layer 2 view, RPR view, IP vie...
Question 209: On the two-fiber bidirectional multiplex section protection...
Question 210: When LCK is inserted into the local ODUk signal, which proc...
Question 211: OTUk_UAS is the unavailable seconds of the optical transmiss...
Question 212: TNG1M404DM board can realize the multiplexing of 4 100Gbit/s...
Question 213: Which of the following are the main features of the overall ...
Question 214: When 61.2M PDH signal is mapped into VC12, the mapping meth...
Question 215: Which of the following is the meaning of "L" in the optical...
Question 216: In a small network, the function of an OptiXtrans DC908 is ...
Question 217: Which of the following descriptions about the FIU board is ...
Question 218: The process from C4 to VC4 during the multiplexing process ...
Question 219: Which of the following descriptions about full-duplex Ethern...
Question 220: When the 80-wavelength OTM site uses M40V for wave combinin...
Question 221: MSTP supports dynamic allocation of bandwidth based on the a...
Question 222: Which of the following descriptions of ODUk_PM_BDI is correc...
Question 223: Which of the following media types has a transmission dista...
Question 224: After mapping and multiplexing, 4 ODU2 signals can be multi...
Question 225: When the sender detects that b6-b8 of the K2 byte is 110, i...
Question 226: SDH is a complete hierarchical structure of standardized dig...
Question 227: TM is a terminal multiplexer, and its functions are: the lin...
Question 228: The number of error blocks in each VC4 channel is detected ...
Question 229: Which of the following options is emitted from an ordinary ...
Question 230: Which of the following is not included in the basic architec...
Question 231: NGWDK adopts LO-L1+L2 triple-extension architecture, in whic...
Question 232: WDM multiplexes optical signals at multiple speeds (waveleng...
Question 233: TU-AIS is often encountered during network maintenance. Whic...
Question 234: Forced switching, fiber switching, manual switching and mot...
Question 235: For OTN interfaces without optical layer overhead, in order...
Question 236: The power SCADA business and communication interface of the...
Question 237: Which of the following does L refer to in the optical modul...
Question 238: When configuring LMSP, there are two switching modes: singl...
Question 239: If one device does not support auto-negotiation, but the ot...
Question 240: In the network interface of OTN, the network interface with...
Question 241: In a 3-7-3 multiplexing line, one VC-12 can transmit () 2.0...
Question 242: Which of the following protections requires the use of the ...
Question 243: The frame rate () and transmission rate of different levels...
Question 244: In OSN550, the CX slot contains a function board integratin...
Question 245: What are the main losses of optical fiber? (Multiple choice...
Question 246: The frame period of OTN signal is fixed and the same as the ...
Question 247: Which of the following alarms will not trigger an AU-AIS ala...
Question 248: Subnet division can reduce network traffic, improve network...
Question 249: The rate of STM-0 is 51.84Mbit/s; (STM-0 is used for digital...
Question 250: SL64 board can be used for OSN2500....
Question 251: The TTI in the segment monitoring overhead SM provides TIM ...
Question 252: By default, if the B2 bit error exceeds which of the follow...
Question 253: R-LOS alarm has nothing to do with overhead bytes but only w...
Question 254: TNV2E224 board does not support which of the following types...
Question 255: H4 is used to indicate the () and () of the payload....
Question 256: When the optical fiber is connected but the business is not...
Question 257: OPC is an optical layer platform board that needs to be used...
Question 258: The 1+1 protection mechanism on the customer side implement...
Question 259: The initial value of the Sequence number in the ETH PWE3 en...
Question 260: TU-AIS is often encountered during network maintenance. The ...
Question 261: In Ethernet, the frame length has a lower limit, which is m...
Question 262: In the system control unit, which of the following database...
Question 263: Number of signal bytes/frame rate of signal = ()...
Question 264: In addition to positioning, the pointer can also accommodat...
Question 265: From the perspective of single board implementation, what ar...
Question 266: Modulation is the process of processing the information of ...
Question 267: Which of the following statements about signal label byte C...
Question 268: The number of ODU2e signals multiplexed into the ODU3 signa...
Question 269: Under which of the following scenario combinations can the ...
Question 270: Which of the following local maintenance terminals can be us...
Question 271: OLA stations can also be monitored using ESC....
Question 272: In the case of 1+1 linear MSP, which of the following switc...
Question 273: Which of the following descriptions about ROADM are correct...
Question 274: The SDH optical interface only scrambles the electrical sign...
Question 275: Additional services cannot be configured on the protection ...
Question 276: The Ethernet board has an external port (Port) and an inter...
Question 277: Mapping is the process of adapting branch signals into () a...
Question 278: Which of the following bridges are used to forward data bas...
Question 279: IEEE802.3 standard is developed for which of the following t...
Question 280: MAC forwarding table: Which of the following items does it c...
Question 281: Which of the following is not a nonlinear effect?...
Question 282: Which of the following optical loss alarms will not cause s...
Question 283: Establish an Ethernet private line service between H (HQ) a...
Question 284: Which of the following maintenance signals is transmitted fr...
Question 285: When the rate of the SNCP ring composed of four OptiX OSN25...
Question 286: Which aspects of the fiber core have a decisive influence on...
Question 287: The refractive index of the core n1 () and the refractive i...
Question 288: Which of the following is the unit that converts non-standa...
Question 289: Which of the following is not one of the main characteristic...
Question 290: G.707 multiplexing line diagram can only multiplex 2M\34M\1...
Question 291: Which of the following layers of overhead belong to the elec...
Question 292: Two PD1 boards and one DMS board jointly implement the TPS ...
Question 293: Which of the following statements about overhead bytes is wr...
Question 294: Which of the following options are correct regarding 1:1 op...
Question 295: Among the maintenance signals at the ODUk level, which of t...
Question 296: What is the structure of STM-16?...
Question 297: Currently, the most commonly used signal is 2Mbit/s. Which ...
Question 298: What is the line code type of the commonly used SDH optical ...
Question 299: Which of the following ITLI-T recommendations define the OT...
Question 300: A local area network is a network formed by interconnecting...
Question 301: When the ACT indicator light of the SDH board is off, it me...
Question 302: Which of the following is the monitoring overhead used to m...
Question 303: SDB is a hierarchical structure of standardized digital sign...
Question 304: In a 25GMSP ring consisting of four MSTP sites, which of th...
Question 305: When the working channel of the optical line protection fai...
Question 306: How many management unit pointers are there in the STM-64 fr...
Question 307: When Severely Errored Seconds (SES) occur in the PM portion ...
Question 308: In Recommendation ITU-TG692, the allowed signal frequencies...
Question 309: Which of the following protocols in the OTN standard system ...
Question 310: Which of the following is the meaning of SFD in the Ethernet...
Question 311: GFP-F is a packet data (PDU) oriented processing mode. It en...
Question 312: For OSN products, changing which of the following parameter...
Question 313: One VC-4 can transmit () VC-12, that is, (63) 2.048 Mbit /s...
Question 314: In the SDH multiplexing structure, the rate represented by V...
Question 315: Which of the following boards supports QinQ function?...
Question 316: The unprotected chain consists of four network elements: NE...
Question 317: What are the main advantages of WDM? (Multiple choice)...
Question 318: QINQ technology solves the problem of insufficient VLAN reso...
Question 319: The STAT indicator on the SDH board flashes red, on for 100m...
Question 320: Which of the following factors will trigger the automatic s...
Question 321: Which of the following does not belong to wavelength divisi...
Question 322: A communication network is a system that interconnects geog...
Question 323: Which of the following networking forms supports additional...
Question 324: Which of the following IP addresses is a Class C IP address?...
Question 325: Which of the following is the difference between AU pointer ...
Question 326: Coherent reception uses a local oscillator laser of the sam...
Question 327: The standard Ethernet frame length should not be less than ...
Question 328: The size of OTUk frame is variable....
Question 329: When there is no frequency difference and phase difference ...
Question 330: Which of the following options are available for ODUk SNCP s...
Question 331: In which ITU-T recommendation is the OTN frame structure def...
Question 332: Optical fiber loss includes bending loss, absorption loss a...
Question 333: Both QinQ and MPLS can provide users with L2 VPN services, ...
Question 334: Refers to the bit used to align and indicate the correspond...
Question 335: The high-speed railway engineering disaster prevention and ...
Question 336: HONET integrated service access network belongs to () access...