350-601 Exam Dumps | An engineer must configure OSPF routing on Cisco Nexus 9000 Series Switches. The IP subnet of the Eth

<< Prev Question Next Question >>

Question 135/219

An engineer must configure OSPF routing on Cisco Nexus 9000 Series Switches. The IP subnet of the Eth 1/2 interface for both switches must be advertised via OSPF. However, these interfaces must not establish OSPF adjacency or send routing updates. The current OSPF adjacency over the interface Eth1/1 on SW1 and Eth1/1 on SW2 must remain unaffected. Which configuration must be applied to both Nexus switches to meet these requirements?

A. interface ethernet 1/2
ip ospf passive-interface

B. interface ethernet 1/2
no ip ospf passive-Interface

C. Interface ethernet 1/2
Ip ospf network point-to-point

D. interface ethernet 1/2
passive-interface default

Question List (219q): Question 1: An engineer needs to install a new package on a Cisco Nexus ...; Question 2: Refer to the exhibit. (Exhibit) An engineer must create a Ba...; Question 3: Which statement describes monitoring Fibre Channel traffic o...; Question 4: A network engineer connects the CNA interface of a server to...; Question 5: An engineer must configure the order in which the server att...; Question 6: A network architect must design an automation solution to in...; Question 7: Refer to the exhibit. An engineer must configure a Fibre Cha...; Question 8: Which component is excluded by default from the host firmwar...; Question 9: A customer asks an engineer to develop an orchestration solu...; Question 10: Refer to the exhibit. (Exhibit) An engineer must configure F...; Question 11: An engineer must allow communication between the APIC contro...; Question 12: An engineer implements a Cisco UCS C-Series Server that must...; Question 13: A network engineer must configure a power redundancy policy ...; Question 14: A QoS policy on Cisco UCS must meet these requirements: * No...; Question 15: Refer to the exhibit. (Exhibit) Which command must be used t...; Question 16: Drag and drop the mechanisms to collect data from a network ...; Question 17: An engineer needs to monitor ingress traffic that arrives at...; Question 18: An engineer must recover the Cisco UCS system The full backu...; Question 19: Refer to the exhibit. (Exhibit) A network engineer must conf...; Question 20: An engineer must implement a disaster recovery policy for th...; Question 21: Which command reduces the amount of time it takes to complet...; Question 22: What is a benefit of Cisco HyperFlex All-Flash Stretched clu...; Question 23: (Exhibit) Refer to the exhibit An engineer must mirror the t...; Question 24: Which component is disrupted when the cisco integrated Manag...; Question 25: An engineer must create an EPG called "Test". The configurat...; Question 26: (Exhibit) Refer to the exhibit. The Cisco Nexus Series Switc...; Question 27: What are two types of FC/FCoE oversubscription ratios? (Choo...; Question 28: An engineer has a primary fabric that is named UCS-A and a s...; Question 29: Drag and drop the Hyperflex characteristics from the left on...; Question 30: A network engineer configures a converged network adapter (C...; Question 31: APIC EPG Resolution Immediacy is set to "Immediate" Which st...; Question 32: Refer to the exhibit. A network engineer must Improve the co...; Question 33: (Exhibit) Refer to the exhibit. Which backup operation type ...; Question 34: An engineer must configure a named VSAN when the fabric inte...; Question 35: Which file service protocol allows the files to appear local...; Question 36: An engineer is designing a cloud solution for an organizatio...; Question 37: Refer to the exhibit. (Exhibit) Which statement describes th...; Question 38: The engineer must configure SPAN on a cisco Nexus 5000 Serie...; Question 39: An engineer must configure Cisco UCS Manager to accept only ...; Question 40: (Exhibit) Refer to the exhibit The communication between the...; Question 41: Refer to the exhibit. (Exhibit) Which two Cisco UCS componen...; Question 42: An engineer upgrades the bash on the Cisco Nexus 9000 Series...; Question 43: A network administrator must perform a system upgrade on a C...; Question 44: A network engineer must create a script to quickly verify IP...; Question 45: An engineer is configuring a vHBA template in UCS Manager. T...; Question 46: Refer to the exhibit. (Exhibit) An engineer configures FCIP ...; Question 47: What is required for using Ansible with HTTP/HTTPS protocol ...; Question 48: A storage array must be connected to port ethernet1/10 on a ...; Question 49: Refer to the exhibit. A network engineer must configure an a...; Question 50: An engineer must configure a Nexus 7000 series switch for HS...; Question 51: AN engineer enters these commands while in EEM on a Cisco Ne...; Question 52: Refer to the exhibit. (Exhibit) What is the result of implem...; Question 53: An engineer must configure the HSRP protocol between two Cis...; Question 54: A network engineer must restore the running configuration on...; Question 55: (Exhibit) Refer to the exhibit. Esxi-server is associated to...; Question 56: A Cisco Nexus 7000 Series switch runs VXLAN, and interface E...; Question 57: Which communication method does NFS use for requests between...; Question 58: An engineer needs to perform a backup of user roles and loca...; Question 59: An engineer must configure multiple EPGs on a single access ...; Question 60: (Exhibit) Refer to the exhibit. An engineer logs all occurre...; Question 61: Which two settings must be configured before enabling a Cisc...; Question 62: An engineer deploys a new Cisco Nexus 5000 Series Switch in ...; Question 63: Which action must be performed before renumbering a Cisco UC...; Question 64: A Cisco UCS user called "Employee1" accidentally changed the...; Question 65: Refer to the exhibit. (Exhibit) Which statement about the ER...; Question 66: What is required for using puppet in a Cisco NX-OS environme...; Question 67: Drag and drop the hyperflex characteristics from the left on...; Question 68: (Exhibit) Refer to the exhibit. An engineer must implement V...; Question 69: (Exhibit) Refer to the exhibit. A host with source address 1...; Question 70: Refer to the exhibit. (Exhibit) What be connected to clear t...; Question 71: A network engineer must configure a Fibre Channel interface ...; Question 72: An engineer must configure SAN connectivity in Cisco UCS man...; Question 73: A customer undergoes an IT security review assessment. The a...; Question 74: What is an advantage of using Ansible for automation as comp...; Question 75: Which two authentication types does Cisco UCS Manager suppor...; Question 76: What happens to the default host firmware policy after a Cis...; Question 77: Drag and drop the NAS features from the left onto the NAS de...; Question 78: An engineer must suggest a deployment model for a newly deve...; Question 79: An engineer must migrate a Cisco UCS C-Series server from Ci...; Question 80: A DevOps engineer must implement a bash script to query a RE...; Question 81: A network engineer needs to upgrade the EPLDs of the fabric ...; Question 82: An engineer must implement a solution that prevents untruste...; Question 83: An engineer must implement private VLANs for a group of Cisc...; Question 84: A customer data center experiences bandwidth contention that...; Question 85: Refer to the exhibit. (Exhibit) An engineer must distribute ...; Question 86: A network engineer must determine the cooling requirements f...; Question 87: What is a benefit of using Cisco Tetration?...; Question 88: An engineer must design an automation solution for the Cisco...; Question 89: Which NFS version uses the TCP protocol and needs only one I...; Question 90: Which method must a network engineer use to upgrade the BIOS...; Question 91: (Exhibit) Refer to the exhibit. A pair of Cisco Nexus switch...; Question 92: An engineer must implement a Cisco UCS system at a customer ...; Question 93: A network administrator must automate the process of pinging...; Question 94: Which two protocols are used by the NFSv4 protocol? (Choose ...; Question 95: Refer to the exhibit. (Exhibit) An engineer reported suspici...; Question 96: The Cisco TACACS+ on a Cisco Nexus Series Switch must authen...; Question 97: What is a benefit of using the Cisco UCS Lightweight upgrade...; Question 98: Refer to the exhibit. (Exhibit) A host with a source address...; Question 99: An engineer must configure a Cisco UCS blade system that is ...; Question 100: An engineer must perform a software upgrade on a production ...; Question 101: Refer to the exhibit. An engineer is performing a Cisco Nexu...; Question 102: Which server policy is used to install new Cisco IMC softwar...; Question 103: An engineer needs to connect Cisco UCS Manager to an externa...; Question 104: (Exhibit) Refer to the exhibit. Which configuration ensure t...; Question 105: A network automation engineer must configure a Cisco NX-OS R...; Question 106: An engineer implements a Python script inside a Cisco Bash s...; Question 107: An engineer must configure OSPF in the data center. The exte...; Question 108: An engineer mus! configure the remote SSH management connect...; Question 109: An engineer troubleshoots an Fibre Channel deployment on a C...; Question 110: An engineer installed a new Nexus switch with the mgm0interf...; Question 111: Where is the witness deployed in a two-node Cisco HyperFlex ...; Question 112: An engineer must implement the FCoE on the Cisco Nexus 9000 ...; Question 113: A network administrator must create a Linux container on a C...; Question 114: An engineer must configure a Fibre Channel port channel on a...; Question 115: Refer to the exhibit. (Exhibit) Two Cisco Nexus Series Switc...; Question 116: Refer to the exhibit. (Exhibit) An engineer configures port ...; Question 117: Refer to the exhibit. (Exhibit) Which action must be taken b...; Question 118: Refer to the exhibit. (Exhibit) Which setting must be config...; Question 119: An engineer must perform a POAP deployment of a Cisco Nexus ...; Question 120: The VMM domain is integrated between Cisco APICs and vCenter...; Question 121: A new user with access privileges in the Finance department ...; Question 122: Which two actions should be taken before an upgrade is start...; Question 123: An administrator is implementing DCNM so that events are tri...; Question 124: An engineer must implement protection against ICMP DoS attac...; Question 125: Refer to the exhibit. (Exhibit) An engineer runs a Python sc...; Question 126: An engineer is asked to manage a large-scale data center and...; Question 127: An engineer must optimize ARP responses and reduce unnecessa...; Question 128: An engineer is performing a configuration on a Cisco Nexus 5...; Question 129: Refer to the exhibit. (Exhibit) What is configured as a resu...; Question 130: (Exhibit) Refer to the exhibit. An engineer is troubleshooti...; Question 131: What are two capabilities of the Cisco Network Assurance Eng...; Question 132: (Exhibit) Refer to the exhibit A network administrator exper...; Question 133: A network engineer is deploying a cisco ALL-flash hyperflex ...; Question 134: Refer to the exhibit. (Exhibit) An engineer needs to impleme...; Question 135: An engineer must configure OSPF routing on Cisco Nexus 9000 ...; Question 136: Drag and drop the storage technologies from the left onto th...; Question 137: An engineer is implementing a Cisco ACI fabric and must use ...; Question 138: A network engineer must download a firmware image from a rem...; Question 139: An engineer must build a lab replica of a Cisco UCS producti...; Question 140: (Exhibit) Refer to the exhibits An engineer must implement a...; Question 141: Refer to the exhibit. (Exhibit) An engineer is implementing ...; Question 142: Refer to the exhibit. (Exhibit) Service degradation is repor...; Question 143: The Cisco UCS blade chassis must send SNMPv3 traps to a netw...; Question 144: An engineer must configure two Cisco Nexus 7000 series switc...; Question 145: An engineer is implementing OTV on a transport that supports...; Question 146: (Exhibit) Refer to the exhibit. Which action completes the v...; Question 147: Which two statements about the process of upgrading an EPLD ...; Question 148: A new employee must be granted access to add VLANs into an e...; Question 149: An engineer must configure a VDS port group using APIC polic...; Question 150: An engineer deploys a custom Guest Shell rootfs on a Nexus 9...; Question 151: (Exhibit) Refer to the exhibit. An administrator must comple...; Question 152: A customer requires a solution to orchestrate the configurat...; Question 153: An engineer configures port security on a Cisco MDS 9000 Ser...; Question 154: (Exhibit) Refer to the exhibit. Which feature must be used t...; Question 155: A SAN administrator must Implement Infrastructure monitoring...; Question 156: (Exhibit) Refer to the exhibit. An engineer must monitor the...; Question 157: A customer asks an engineer to develop a framework that will...; Question 158: A SAN administrator must Implement Infrastructure monitoring...; Question 159: Which data interchange format is presented in this output? (...; Question 160: An engineer is implementing traffic monitoring for a server ...; Question 161: Which two actions must be taken to directly connect a Fibre ...; Question 162: An engineer performs a Cisco UCS C480 ML M5 installation fro...; Question 163: Refer to the exhibit. (Exhibit) An engineer must monitor all...; Question 164: Refer to the exhibit. (Exhibit) The Cisco NX-OS scheduler mu...; Question 165: Refer to the exhibit. (Exhibit) A VXLAN data center fabric c...; Question 166: Refer to the exhibit. (Exhibit) An engineer must configure f...; Question 167: Which two statements describe modifying Cisco UCS user accou...; Question 168: An engineer must perform an initial configuration of VXLAN T...; Question 169: What is a benefit of independent resource scaling in Cisco H...; Question 170: An engineer must create a scheduler configuration to create ...; Question 171: Which two features are used to allow a nondisruptive upgrade...; Question 172: A network architect considers a Cisco HyperFlex design solut...; Question 173: A server engineer wants to control power uses on a Cisco UCS...; Question 174: (Exhibit) Refer to the exhibit. An engineer monitors ingress...; Question 175: (Exhibit) Refer to the exhibit. A network engineer is implem...; Question 176: A DNS server with IP address 192.168.1.1 is deployed in a da...; Question 177: A POAP-enabled Cisco Nexus switch will not enter POAP mode. ...; Question 178: Which mroute state is created when Bidirectional PIM is depl...; Question 179: Refer to the exhibit. (Exhibit) Which configuration ensure t...; Question 180: (Exhibit) Refer to the exhibit. An engineer must deploy 70 C...; Question 181: The EPLD update of the supervisor module has been scheduled ...; Question 182: A customer has a requirement for an automation solution that...; Question 183: What is an advantage of NFS as compared to Fibre Channel?...; Question 184: An engineer is configuring AAA authentication on an MDS 9000...; Question 185: Refer to the exhibit. (Exhibit) Which backup operation type ...; Question 186: (Exhibit) Refer to the exhibit. A secure server that provide...; Question 187: An engineer configures a role for a new user in Cisco UCS Ma...; Question 188: An engineer is configuring VNTag between a virtualized serve...; Question 189: An engineer must recover configuration on a Cisco MDS 9000 S...; Question 190: Port security is enabled on a Cisco MDS 9000 series Switch. ...; Question 191: (Exhibit) Refer to the exhibit. Software downgrade is requir...; Question 192: Host 1 is in VLAN 100 located is DataCenter 1 and Host2 is i...; Question 193: Where does the witness VM reside in a Cisco Hyperflex Edge d...; Question 194: An engineer is implementing Cisco Intersight in a secure env...; Question 195: Refer to the exhibit. (Exhibit) A network engineer plans to ...; Question 196: Refer to the exhibit. A Cisco data center environment is imp...; Question 197: An engineer performs a set of configuration changes for the ...; Question 198: Which MAC address is an HSRP version 2?...; Question 199: Port security is statically configured on a Cisco Nexus 7700...; Question 200: The Cisco Nexus 5600 Series Switch experiences occasional pa...; Question 201: Refer to the exhibit. (Exhibit) An engineer is connecting a ...; Question 202: A company plans to migrate some of its services to the cloud...; Question 203: What is a characteristic of EPLD updates on Cisco MDS 9000 S...; Question 204: Cisco Nexus 9000 Series Switches are configured with LACP pr...; Question 205: Which configuration generates a syslog message when CPU util...; Question 206: Refer to the exhibit. (Exhibit) The server is sending traffi...; Question 207: Refer to the exhibit. (Exhibit) An engineer configures an FC...; Question 208: An engineer must generate a checkpoint of the running config...; Question 209: (Exhibit) Refer to the exhibit. An engineer must schedule th...; Question 210: A network engineer must create an EEM script that saves a co...; Question 211: An engineer must create a new Cisco UCS user account to perf...; Question 212: An engineer must configure a monitoring solution for a Cisco...; Question 213: An engineer is asked to use SaaS to manage Cisco computing. ...; Question 214: Which Cisco UCS Manager XML encoded backup type must be used...; Question 215: A content delivery network sends video traffic to a multicas...; Question 216: (Exhibit) Refer to the exhibit. A network engineer is config...; Question 217: An engineer is implementing VSANs on a Cisco MDS 9000 Series...; Question 218: A network engineer must implement a telemetry solution to co...; Question 219: When deploying a Cisco HyperFlex edge with a pair of switche...

Question 135/219

LEAVE A REPLY

Download PDF File