RCDD-001 Exam Dumps | You are extending 1000 MHz video service from your existing headend to a new equipment room (ER). Your

<< Prev Question Next Question >>

Question 200/334

You are extending 1000 MHz video service from your existing headend to a new equipment room (ER).
Your existing incoming video signal is plus (+) 15 dBmV. You have three two-way splitters with a total of minus (-) 15 dB. You are adding 122 m (400 ft) of series 11 (RG 11) cable with a minus (-) 18 dB with eight single end F-connectors with a total of minus (-) 1.2 dB. From the selections below, what is the MINIMUM gain amplifier required in the headend room?

A. Plus (+) 15 dB

B. Plus (+) 35 dB

C. Plus (+) 25 dB

D. Plus (+) 20 dB

E. Plus (+) 30 dB

Question List (334q): Question 1: Exhibit: (Exhibit) This diagram illustrates a ______________...; Question 2: IPv-4 addresses are ________ bits in length....; Question 3: The MINIMUM recommended lighting requirement in a telecommun...; Question 4: One advantage of using preconnectorized jumpers and cables i...; Question 5: Which device supplies the radio signal into a DAS (distribut...; Question 6: Which of the following correctly lists the lowest frequency ...; Question 7: Data representation including code translations, compression...; Question 8: You are designing a paging system for a 588 sq m (6325 sq ft...; Question 9: In an industry where a high level of humidity is measured, w...; Question 10: You must extend a video systems backbone coax cable that was...; Question 11: When developing a safety plan, consider all of the following...; Question 12: What type of material does NOT support combustion even under...; Question 13: Which of the following is NOT an advantage of access floor s...; Question 14: To reduce the chance of an accidental dig-up, plastic warnin...; Question 15: Which of the following statements best describes what a back...; Question 16: When installing a heavy backbone cabling vertically, recomme...; Question 17: As a wireless designer, you have been tasked with designing ...; Question 18: Which of the following is NOT a primary method of transporti...; Question 19: You are placing Category 6 unshielded twisted-pair (UTP) in ...; Question 20: Which of the following is NOT a type of intrusion detection ...; Question 21: Assume that the optical power transmitted by a 62.5/125 mult...; Question 22: What is the MINIMUM vertical separation between the top rail...; Question 23: An open office design is made up of three furniture clusters...; Question 24: An active video converter is used in what type of CATV cable...; Question 25: You are renovating telecommunication rooms that support an a...; Question 26: Geographically speaking, a __________ covers an area associa...; Question 27: Perimeter raceway systems should be used primarily for:...; Question 28: You are designing a large equipment room (ER) that will hous...; Question 29: You have been selected to recommend a solution to increase r...; Question 30: You are designing a cabling system for a chemical plant. Wha...; Question 31: You are designing a cabling containment system installed ove...; Question 32: Which electrical characteristic is displayed with the correc...; Question 33: Which of the following refers to the increase in the nominal...; Question 34: The MINIMUM separation distance between grounded metal telec...; Question 35: When installing outlet boxes in ten private offices in an ar...; Question 36: The average power consumption in a telecommunications room (...; Question 37: You are designing a multi-story dwelling and need to place t...; Question 38: A video camera has a coaxial cable output. The video signal ...; Question 39: Active video converters are required for what type of CATV d...; Question 40: In (ESS) design, employees, reputation, and materials are al...; Question 41: You have discovered a common mode current on the metallic ca...; Question 42: Which device uses circulators or diplexer filters to separat...; Question 43: In order to maximize its ability to send and receive, an ant...; Question 44: Which of the following is NOT a type of connector for optica...; Question 45: Assuming the total fill capacity of a pathway is 100 cables ...; Question 46: You have been asked what the estimated power cost will be pe...; Question 47: What is the expected life cycle, in years, of building autom...; Question 48: In an office area, a consultant needs to add the location of...; Question 49: Which one of the following is NOT an advantage of direct-bur...; Question 50: Within a data center, if you have a system which includes on...; Question 51: Geographically speaking, a ______ links two or more distant ...; Question 52: This type of cable is an unbalanced system:...; Question 53: A ________ eliminates the need to remove or install material...; Question 54: In reviewing your client's network needs for today and 5 yea...; Question 55: Which of the following is NOT an element of a cable system?...; Question 56: What type of redundancy provides two complete units, modules...; Question 57: Electrical power cables are usually routed above aerial cabl...; Question 58: Exhibit: (Exhibit) A pay telephone using coins needs to be i...; Question 59: What is the MINIMUM ceiling height of a telecommunications r...; Question 60: The three electronic security system (ESS) concepts the cons...; Question 61: The decision regarding the number of optical fibers to insta...; Question 62: The headend has several audio-video playback devices within ...; Question 63: What type of redundancy provides two additional units, modul...; Question 64: What is the highest typical ambient noise level where audio ...; Question 65: If you are working on a physical security plan for a data ce...; Question 66: Exhibit: (Exhibit) The figure below represents what type of ...; Question 67: Within a commercial office building of 2300 sq m (25000 sq f...; Question 68: For design purposes, loudspeakers are rated for a measured s...; Question 69: When considering the DAS, which component acts as a bidirect...; Question 70: Which of the following is true about screened twisted pair c...; Question 71: Optical transmitters are typically one of the following type...; Question 72: Two sinusoidal signals have the same amplitude (A) and the s...; Question 73: If the input signal power to a communication system is 1 W a...; Question 74: Which of the following is an undesirable electromagnetic eff...; Question 75: Often associated with raised flooring, a(n) ________ may con...; Question 76: The electromagnetic spectrum of visible light lies in the __...; Question 77: When reviewing a backbone distribution system within a build...; Question 78: Phase difference is the relationship in time between two wav...; Question 79: Which of the following is an alarm management output system?...; Question 80: What type of facility requires a building automation system ...; Question 81: What type of fiber optic cable is manufactured to protect in...; Question 82: Exhibit: (Exhibit) In this future marina layout, what would ...; Question 83: You are designing a 4.9 GHz microwave system that is using r...; Question 84: ITU-T G.655 recommends which type of singlemode optical fibe...; Question 85: In a hallway with normal traffic, ceiling mounted speakers s...; Question 86: What is the MOST important aspect of fire alarm signaling?...; Question 87: BICSI recommends that any trench ________ or more deep must ...; Question 88: If you are using a building automation system (BAS) protocol...; Question 89: The MOST common medium used to provide service to the access...; Question 90: The ability of a conductors insulation to transmit an electr...; Question 91: The F rating for a framed wall/stud wall is ________ hour(s)...; Question 92: What is the air change requirement for a tunnel of 610 m (20...; Question 93: The RJ-45 is now known as the 8P8C style connector, per the ...; Question 94: You are designing a DAS system that has a requirement to sup...; Question 95: You are starting work on a new high school. The architect ha...; Question 96: Which of the following is used to create an electronic signa...; Question 97: Which type of protection for electrical power stations provi...; Question 98: You are designing a firestop system for a hospital with seve...; Question 99: Which of the following is NOT a primary type of DAS antenna?...; Question 100: Color codes for cross-connections fields have been used for ...; Question 101: A scope of work should contain all of the following EXCEPT:...; Question 102: Assume the following: - An equipment room (ER) consists of 1...; Question 103: Which layer of the OSI model covers physical cable connectio...; Question 104: The maximum vertical rise is the distance over which the cab...; Question 105: You are designing a firestop system for a boiler room that w...; Question 106: A fire ________ is a contained area that is completely enclo...; Question 107: It is important to keep all underfloor cabling systems very ...; Question 108: If looking to specify an optical fiber backbone within a bui...; Question 109: You have been asked to test and troubleshoot an installed ba...; Question 110: A rapid increase in voltage with a duration of half a cycle ...; Question 111: What is the insertion loss guideline for a multimode mechani...; Question 112: The recommended ratio of patch panels to horizontal cable ma...; Question 113: What is the PERT estimate (in hours) for project design wher...; Question 114: In the customer's environment, an ITS designer should avoid ...; Question 115: Which is NOT a type of contract?...; Question 116: Within a data center, how many concentric layers are conside...; Question 117: You are required by architectural design to place UTP cables...; Question 118: A space has all hard surfaces including architecture and fur...; Question 119: You are recommending to an architect the location within a t...; Question 120: The formula for calculating BTUs from electrical power is:...; Question 121: An existing ceiling raceway system has 115,000 sq mm (177 sq...; Question 122: Which of the following types of conduit uses set screw coupl...; Question 123: Coupling with electrical circuits can create inductive inter...; Question 124: Which of the following is NOT considered acceptable in an in...; Question 125: You have been asked to provide a N+1 level of power redundan...; Question 126: Exhibit: (Exhibit) If a work breakdown structure (WBS) shows...; Question 127: The concept of the "security quandary" is based on providing...; Question 128: Cementitious materials are ________ based materials....; Question 129: The ability of a device to withstand electromagnetic disturb...; Question 130: A SONET OC-1 channel can carry 672 voice signals and has a d...; Question 131: What is the frequency rating of an International Organizatio...; Question 132: Omnidirectional antennas broadcast equally in all directions...; Question 133: Given the following values, calculate the focal length of th...; Question 134: Generating multiple message frames containing identical data...; Question 135: What device is used in both wired and wireless networks to l...; Question 136: The potential for ______ occurs when devices or systems shar...; Question 137: In a telecommunication room (TR), the ________ is the facili...; Question 138: Which service is NOT typical of Grade 1?...; Question 139: A building has six floors plus a basement. Each floor is 929...; Question 140: You are designing a building with a combination of Class A c...; Question 141: All of the following are true about the post construction ph...; Question 142: You are designing a nurse call system for a health care faci...; Question 143: Within building automation hardware systems, there is a hier...; Question 144: A telecommunications outlet/connector may be provided using ...; Question 145: Which of the following is NOT true about consolidation point...; Question 146: You must place a cable between 2 equipment locations with se...; Question 147: When designing a connection to an outlying building you deci...; Question 148: Premises optical fiber links should be tested:...; Question 149: A work breakdown structure is:; Question 150: You are designing the cabling infrastructure for a lab offic...; Question 151: Exhibit: (Exhibit) The following diagram represents what typ...; Question 152: What is at the "root" of a DAS (distributive antenna system)...; Question 153: Based on documentation contained within the Insulated Cable ...; Question 154: On a survey of one of your client's buildings, you discover ...; Question 155: Which of the following is NOT a form of signal coupling betw...; Question 156: What is the horizontal separation, in well tamped earth, req...; Question 157: On a project with three small conference rooms, a break room...; Question 158: You are designing a telecommunications grounding system for ...; Question 159: The standard floor space coverage area for each building aut...; Question 160: You are designing distribution for a seven unit townhouse wi...; Question 161: Cables are installed in a ceiling in a straight line. The ce...; Question 162: During a site survey you notice that several CRT displays in...; Question 163: A backbone star topology shall have no more than______ level...; Question 164: The ________ system is an application used for storing and v...; Question 165: You are working on the design of a new, large ER/TR that wil...; Question 166: You are placing PTP fiber between two locations 55 km (34 mi...; Question 167: Using Ohms law, a circuit of 120 volts and a resistance of 1...; Question 168: A security program consists of three independent components....; Question 169: Exhibit: (Exhibit) What does this international symbol stand...; Question 170: Which one of the following is part of the security metric to...; Question 171: What is the testing frequency of a Category 6/Class E cable?...; Question 172: What type of optical fiber is used primarily for outside pla...; Question 173: You are designing a four story retail mall and multiple soun...; Question 174: You are placing two 423 mm (19 in) relay racks with a 152 mm...; Question 175: A building has a floor space of 16.7 m (55 ft) by 45 m (150 ...; Question 176: Which class of the system was created to secure a single equ...; Question 177: Rack mounted hardware is installed in two standard sized rac...; Question 178: What type of address is 00-A1-C3-52-CE-11?...; Question 179: You are designing a restaurant located within a retail mall....; Question 180: For an analog camera, what is the normal frame rate in frame...; Question 181: All entrance conduits should be equipped with a plastic or n...; Question 182: The RECOMMENDED balanced twisted-pair cable for building bac...; Question 183: The propagation and path loss of radio signals in the target...; Question 184: In addition to voice and data services, an equipment room (E...; Question 185: The recommended MAXIMUM value for the bonding resistance bet...; Question 186: For the telecommunications industry, the nominal operating v...; Question 187: As a guide, the recommended maximum AC current value on any ...; Question 188: Buildings larger than ________ must contain a dedicated room...; Question 189: Wave division multiplexing (WDM) is most similar to:...; Question 190: Vertical conduit masts (with approved service heads) are lim...; Question 191: You have been asked to design a public safety microwave radi...; Question 192: A reasonable approximation for the signal speed in 100 ohm b...; Question 193: What is the MAXIMUM horizontal cable length permitted for ce...; Question 194: You are designing a 4.9 GHz microwave system that is using r...; Question 195: When placing an optical fiber cable in the horizontal optica...; Question 196: Multimode optical fiber is generally used for campus or buil...; Question 197: You are placing an entrance cable between two buildings conn...; Question 198: Which of the following is NOT an example of a perimeter path...; Question 199: At the end of the third week of a project, the actual cost o...; Question 200: You are extending 1000 MHz video service from your existing ...; Question 201: When designing a campus distribution system involving small ...; Question 202: You are reviewing a building backbone design with a vertical...; Question 203: Which is NOT true about conformance quality?...; Question 204: Which one of the following is NOT an advantage of undergroun...; Question 205: The conversion of an analog speech signal to a pulse code mo...; Question 206: From a 1000 ft (305 m) roll of optical fiber, how many MAXIM...; Question 207: Which area of project management covers the blending of vari...; Question 208: The impedance of the equipment grounding conductor can only ...; Question 209: When designing a backbone distribution system, you are asked...; Question 210: A campus backbone design linking two buildings requires that...; Question 211: You are designing a strobe visual notification system for a ...; Question 212: Which of the following does NOT describe one of the four mai...; Question 213: If the usable floor space is unknown, then deduct ________ p...; Question 214: You have been asked to project manage a fiber cable backbone...; Question 215: You have determined that the equipment room (ER) you are des...; Question 216: You are designing a horizontal distribution system that will...; Question 217: Which wireless device should be used to support 3 computers ...; Question 218: What element is typically NOT part of a paging system?...; Question 219: Color codes for cross-connection fields have been used for m...; Question 220: You have just finished a design calling for 15 telecommunica...; Question 221: What warning tape color has the Common Ground Alliance (CGA)...; Question 222: You are designing multi band UHF police radio and VHF fire r...; Question 223: At a minimum, convenience receptacles in an ER or TR are to ...; Question 224: The information technology system (ITS) designer should desi...; Question 225: When allocating termination space for CAT 6 and optical fibe...; Question 226: One interior TTY must be provided at locations defined as pu...; Question 227: When designing a backbone distribution system, you will need...; Question 228: A(n) ________ system is considered a mechanical firestop....; Question 229: When designing a fiber backbone using cable with an armored ...; Question 230: What is the recommended distance between ceiling mounted spe...; Question 231: Exhibit: (Exhibit) The diagram below is a typical configurat...; Question 232: When selecting poles for aerial telecommunications facilitie...; Question 233: Important considerations when designing telecommunications d...; Question 234: If you have a 30 cm (12 in) wide data tray, what does ANSI/T...; Question 235: As a guide, the MAXIMUM recommended DC current value on any ...; Question 236: An outside plant (OSP) cable must be placed under a pipeline...; Question 237: In new construction, what is the percentage of pay phones th...; Question 238: If a telecommunications grounding busbar is installed in the...; Question 239: The signal at the input to a balanced twisted pair cable is ...; Question 240: The information technology system (ITS) designer should desi...; Question 241: A 24 port layer 2 switch can perform all of the following fu...; Question 242: A common mode (CM) signal can be converted to a differential...; Question 243: To accommodate telephone, data, CATV, security and multimedi...; Question 244: A large telecommunications facility, by most codes, must be ...; Question 245: If you have a circuit with 120 volts, 12 amps, and 10 ohms, ...; Question 246: If you have a data center where the entire infrastructure mu...; Question 247: You are designing an audible alarm notification system for a...; Question 248: Using the "pathway design" for horizontal cable distribution...; Question 249: The standard floor space coverage area for each building aut...; Question 250: A properly designed distributed paging system will provide a...; 2 commentQuestion 251: Exhibit: (Exhibit) A pay telephone using coins needs to be i...; Question 252: You are designing an interactive patient television system (...; Question 253: A furniture cluster with 26 requires a MINIMUM of how many m...; Question 254: A building has a series of CATV outlets each with cables ins...; Question 255: "A single outlet utilizing a dedicated phase, neutral, and g...; Question 256: What is the MINIMUM distance from the edge of a pool or othe...; Question 257: Route congestion and message priority are a few of the funct...; Question 258: What type of address is 10.162.02.14?...; Question 259: Which of the following is true when describing slip sleeves ...; Question 260: All of the following are nominal wavelengths for laser light...; Question 261: You are working with the Sheriff's Department to develop a p...; Question 262: What is the International Organization for Standardization/I...; Question 263: When labeling pathways, which one of the following guideline...; Question 264: What type of estimate is based on the cost of performing sim...; Question 265: Firestop ________, in conjunction with steel wedging plates,...; Question 266: Time division multiplexing (TDM) systems are designed to tra...; Question 267: Which of the following is a nonmechanical firestop system?...; Question 268: You are designing a horizontal pathway system where you will...; Question 269: You are designing a system requiring the transmission of dat...; Question 270: A ______ intercepts a file and stores it temporarily in queu...; Question 271: What is the MINIMUM clearance needed between the front of th...; Question 272: What are the three typical voltages used in centrally amplif...; Question 273: Which of the following electrical devices is used to convert...; Question 274: You are designing a DAS that will support five buildings on ...; Question 275: What is the appropriate impedance of coaxial cable for use w...; Question 276: Certain systems must exist relative to bonding and grounding...; Question 277: Exhibit: (Exhibit) In this future marina layout, assuming th...; Question 278: The MAXIMUM span length for an aerial entrance, from the las...; Question 279: Exhibit: (Exhibit) This diagram illustrates an example of a:...; Question 280: Which of the following covers lightning protection systems a...; Question 281: All of the following are used to control static discharge EX...; Question 282: Color codes for cross-connections fields have been used for ...; Question 283: The headend has several modulators assigning frequencies for...; Question 284: You have been asked to provide a UPS that is always serving ...; Question 285: The loop distance range in an "ethernet in the first mile" (...; Question 286: You have been selected to do the telecommunications design o...; Question 287: Which of the following protocols is referred to under ISO 16...; Question 288: There are three buildings approximately 400 meters apart and...; Question 289: You must place CAT6 cable above a factory floor with automat...; Question 290: You are preparing to test newly installed open office cablin...; Question 291: How much area of wall space is needed in the telecommunicati...; Question 292: Class ________ administration provides for the telecommunica...; Question 293: One of the advantages of using optical fiber in the backbone...; Question 294: MAC addresses are _____________ bits in length....; Question 295: Within a data center, if you have dual path connectivity bet...; Question 296: All of the following are considered market or regional condi...; Question 297: The recommended MINIMUM number of conduits connecting two lo...; Question 298: Which of the following is NOT a source of electromagnetic in...; Question 299: Which of the following is NOT provided by the ac grounding e...; Question 300: Which is an advantage of stranded conductors over solid cond...; Question 301: A tapped trunk topology uses ________ cabling to support a D...; Question 302: What is the PERT estimate of time for cable placement on a g...; Question 303: An isolated ground is used to:; Question 304: The distance a CCTV signal may be run is determined by the s...; Question 305: You have been asked to spec the physical security requiremen...; Question 306: DC loads are generally expressed in:...; Question 307: You have determined that your underground cable design requi...; Question 308: What is the recommended MINIMUM separation of unshielded twi...; Question 309: You have the responsibility of designing a railroad track cr...; Question 310: When a building is not on the property line, the building ow...; Question 311: Select the appropriate task to complete the section 2.2 of t...; Question 312: When specifying telecommunications outlet boxes, all of the ...; Question 313: A building can have multiple equipment rooms (ERs) for all o...; Question 314: You have been asked to design a backbone cable connecting tw...; Question 315: Which class of the system applies when the premise only has ...; Question 316: A conduit run is installed from the ER to a TR. It has two (...; Question 317: The purpose of QoS on an IP network is for:...; Question 318: At the end of the second week of a project, the earned value...; Question 319: In a run requiring 15 m (50 ft) of cable between the floor d...; Question 320: What is the worst case acceptance value for attenuation when...; Question 321: The ITU-T G.711 standard deals with what aspect of video con...; Question 322: When trying to control radio signals from leaking outside of...; Question 323: Where backbone cabling exceeds cabling lengths for the same ...; Question 324: When installing underground entrances, no more than ________...; Question 325: Using the sound pressure level (SPL) method of approximating...; Question 326: Most types of firestop putty have ________ properties....; Question 327: What does ANSI/TIA 942 recommend as the MINIMUM height for o...; Question 328: An isolated ground receptacle may be identified by:...; Question 329: A telephone facility and an electrical facility are required...; Question 330: You have just assumed management responsibility over an olde...; Question 331: What is the MINIMUM cover for underground conduit?...; Question 332: Aerial entrances to small buildings should be limited to ___...; Question 333: Multiples of the basic frequency of an electrical waveform a...; Question 334: In a telecommunications room (TR), the MINIMUM bottom edge h...

Question 200/334

LEAVE A REPLY

Download PDF File